What is the battery model for BMW remote control?

2 Answers
LaRowan
07/29/25 2:56pm
The battery model for BMW remote control is CR2032, which is a button cell. Most models of remote key batteries use CR2032. The advantages of using this lithium button battery are its small size and long lifespan, typically lasting more than 3 years. The BMW 525 is a high-end 4-door, 5-seat sedan under the BMW brand, with body dimensions of 5106mm in length, 1868mm in width, and 1500mm in height, and a wheelbase of 3105mm. It is equipped with an 8-speed automatic transmission. The BMW 525 is powered by a 2.0T turbocharged engine, with a maximum power output of 135 kW and a maximum torque of 290 Nm.
Was this review help?
2
5
Share
CooperDella
08/13/25 7:29am
I've been driving a BMW for several years, and the remote key battery is usually a CR2032 coin cell. I've replaced it several times, and it's not difficult to do: first, unscrew the small screw on the back cover of the key—a flathead screwdriver will do—then pop out the old battery and replace it with a new CR2032. Be careful not to insert it the wrong way; the positive side should face up. The battery lasts about two to three years, and replacing it early can avoid the awkward situation of suddenly being unable to unlock the car door. Last week, I encountered this issue once, but luckily, I had a spare battery in the car and replaced it right away. Buying one online or at an auto parts store is very cheap, about 10 yuan each. Avoid using off-brand batteries; stick to original or high-quality ones to prevent leakage. If the remote feels sluggish, check the battery life promptly.
Was this review help?
4
4
Share
Expand All
More Forum Discussions

What to Do When the Haval H6 Battery Dies and the Car Won't Start?

Haval H6 without power can be started using the following three methods: Push Start: Push starting is the most familiar and effective emergency starting method, but it is a last resort and should not be used frequently, as it can cause some damage to the engine and clutch. This method should especially be avoided for automatic transmission vehicles. Tow Start: The method and principle of tow starting are similar to push starting, but towing is often more effortless and convenient. When implementing this method, use a tow rope of appropriate length and secure both ends firmly. Before towing, the drivers of both vehicles should agree on communication signals, such as using horns or hand gestures to indicate starting and stopping, to ensure coordinated action. Jump Start: If the battery is dead and there is another vehicle with jumper cables available, the jump-start method can be used to start the car. During the operation, bring the two vehicles close enough so that the jumper cables can connect the positive and negative terminals of both batteries. Ensure that the two vehicles do not touch each other, and only use cables with sufficient capacity and insulated sheathing.
7
3
Share

What is the emission standard of the Honda CR-V?

The Dongfeng Honda CR-V manufactured in October 2013 meets the China IV emission standard, while those produced after 2015 generally comply with the China V standard. Below are the detailed specifications of the Honda CR-V: Powertrain: The Honda CR-V is equipped with two i-VTEC engines: a 2.0L and a 2.4L. The 2.0L engine delivers a maximum power of 114kW and a peak torque of 190N·m, while the 2.4L engine produces a maximum power of 140kW and a peak torque of 222N·m. VTEC Technology: The Honda CR-V features VTEC engine technology, which stands for Variable Valve Timing and Lift Electronic Control System. Unlike conventional engines, the VTEC engine differs in the number and control method of camshafts and rocker arms. It has two distinct sets of valve drive cams for low-to-medium speeds and high speeds, which can be automatically switched via electronic control system adjustments. The VTEC system allows the engine to automatically adjust the valve opening timing and lift according to driving conditions, thereby altering the intake and exhaust volumes. This results in increased power output, reduced fuel consumption, and lower emissions.
15
0
Share

Why does the keyless entry of Sagitar fail but can be unlocked with buttons?

The reasons why the keyless entry of Sagitar fails but can be unlocked with buttons are as follows: Poor soldering in the power distribution box: Poor contact caused by poor soldering can also lead to the failure of the sensor's operation. The most "down-to-earth" method is to gently tap the power distribution box with your hand, which might reconnect the poorly soldered points. However, this is not a long-term solution, and it is still necessary to go to a professional repair shop for repair. Signal being blocked: There is a signal blocker (such as a transformer) in the location where the owner and the vehicle are located, interfering with the signal between the key and the central control unit. Fault in the central locking system: It may be that the circuit fuse of the door lock is burned out, causing an open circuit.
4
5
Share

What is the Dago car?

Dago is a compact SUV under the Haval brand, with dimensions of 4620mm in length, 1890mm in width, 1780mm in height, and a wheelbase of 2738mm. Advantages of the Dago: Its retro exterior design aligns with current trends, and its rugged style appeals to young consumers. Built on the new Lemon platform, it offers gasoline, plug-in hybrid, and pure electric variants. The NVH engineering is excellent, and the chassis tuning shows significant improvement over previous models. Disadvantages of the Dago: The 1.5T small-displacement engine still struggles at medium to high speeds. The transmission prioritizes smoothness over shift speed. It has noticeable tire noise, high fuel consumption, and lacks lumbar support.
10
2
Share

What Causes Slow Tire Leaks in Cars?

Here are the specific reasons for slow tire leaks in cars: Foreign objects puncturing the tire: Common objects that can puncture tires include nails, screws, and sharp stones. Nails and screws can easily penetrate the tire, causing slow leaks, and may remain embedded in the puncture site. If not removed promptly, they can worsen the damage to the tire. Damage to the tire sidewall or inner edge: The sidewall and inner edge of a tire are vulnerable areas. Damage to the inner edge often occurs during improper installation or removal of the tire from the wheel rim, typically during tire replacement or after a repair. Damage to the sidewall or inner edge can lead to slow leaks and significantly increase the risk of a blowout. Faulty tire valve stem: Most passenger cars are equipped with tubeless tires, where the valve stem is mounted on the wheel rim and is usually made of rubber. Over time, rubber valve stems can harden and become brittle, eventually cracking and causing air leaks. Deformed wheel rim flange: When a car tire is fully inflated, the outer edge of the tire seals tightly against the wheel rim flange to prevent air leakage. If the wheel rim flange is deformed due to impact, it can compromise the seal with the tire's outer edge, resulting in a slow leak.
1
3
Share

How many kilowatt-hours does it take to fully charge the Leapmotor T03?

It uses CATL's NCM811 battery cells with a capacity of 36.5 kWh and an energy density of 171 Wh/kg. Actual charging time: The actual charging time when using a new energy electric vehicle mainly depends on the capacity of the lithium battery configured in the electric vehicle and the capacity of the charging station. Under normal circumstances: It is best to charge an electric vehicle when the remaining battery power is between 30% and 50%, which can avoid early battery capacity loss and over-discharge; if you frequently carry passengers or climb slopes, it is recommended to charge when the remaining power is at 50%.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.