What is the APS switch on the car radio?

Why does the brake pedal feel different after a machine brake fluid change?

After a machine brake fluid change, the different pedal feel may be due to air not being fully bled from the system, requiring a break-in period, or needing to replace the brake fluid again. Characteristics of automotive brake fluid: Automotive brake fluid is the liquid used in hydraulic brake systems. It is unaffected by high temperatures and does not corrode or cause softening and expansion of metals and rubber. The volume of brake fluid changes with temperature, so the brake fluid reservoir cap has a vent hole. The air drawn in through this hole contains moisture, which is absorbed by the brake fluid, lowering its boiling point. After prolonged driving, the temperature of the braking system rises, making it prone to vapor lock. Compressed air can reduce braking force or cause brake failure, so regular replacement of brake fluid is necessary. Method for bleeding the brakes: First, two people need to cooperate to avoid mistakes. One person presses the brake pedal 4-5 times, while the other loosens the bleeder screw on the brake caliper. If there is air in the brake line, some brake fluid and gas will be expelled. Repeat this process until only brake fluid comes out, indicating all air has been removed. Finally, tighten the bleeder screw to complete the process.

19

4

Share

What are the reasons why the Volkswagen Santana is difficult to start?

The Volkswagen Santana may be difficult to start due to issues such as the engine not working or even the starter failing, the car being out of fuel, a dead battery, faulty spark plugs, or a damaged fuel pump. Electrical or electronic faults: First, it could be an electrical or electronic fault. The symptoms often appear suddenly without any warning. Electrical faults include: blown fuses, open circuits in the high-voltage coil, open circuits in the low-voltage circuit, detachment of the central ignition wire, leakage in the distributor rotor, or damaged spark plugs. Electronic faults mainly refer to the failure of the central computer control board. Fuel system faults: Stalling caused by fuel system faults often comes with symptoms such as weak engine performance and a spongy feel when pressing the accelerator pedal. Possible locations of fuel system faults include: fuel pump failure, blocked fuel lines, clogged fuel filters, carburetor malfunction, damaged injectors, etc. Sometimes, the fuel tank may also be empty without the owner realizing it.

11

5

Share

Should a Bent Engine Connecting Rod Be Replaced?

For safety reasons, it is advisable to replace a bent engine connecting rod. Consequences of a bent connecting rod: When the water level exceeds the engine's air intake during water wading, water can be sucked into the engine cylinders. Since water is incompressible, the immense reverse force can cause the connecting rod to bend and rub against the engine cylinder block. In severe cases, this can lead to a bent connecting rod, a broken crankshaft, or even damage to the cylinder block. Effects after repairing the connecting rod: After repairing a bent engine connecting rod, it generally does not affect normal use. However, even with careful reassembly, the engine may not meet the original manufacturer's standards. This is because it's impossible to guarantee that the new parts will have identical parameters to the original components in all aspects. There might be slight impacts on power and noise levels. Additionally, the newly replaced parts require a break-in period with the vehicle. During this time, avoid heavy acceleration or overloading the engine, and refrain from aggressive driving in daily use.

15

1

Share

What is the basic structure of a motorcycle?

The basic structure of a motorcycle consists of five parts: the engine, transmission system, running system, steering, braking system, and electrical instrumentation equipment. Characteristics of motorcycle engines: The engine is a two-stroke or four-stroke gasoline engine; it uses air cooling, which can be either natural air cooling or forced air cooling; the engine operates at high speeds, generally above 5,000 RPM; the engine's crankcase is integrated with the clutch and gearbox, making the structure compact. Engine block structure: The engine block is composed of three parts: the cylinder head, cylinder body, and crankcase. The cylinder head is cast from aluminum alloy with cooling fins. Modern four-stroke motorcycle engines adopt an overhead valve, chain-driven, overhead camshaft structure. Crankshaft and connecting rod: The crankshaft of a motorcycle engine is of a combined type, formed by pressing together the left half-shaft, right half-shaft, and crankpin. The main journal of both half-shafts is equipped with ball bearings to support the crankshaft in the crankcase. The ends of the crankshaft are fitted with a flywheel, magneto, and clutch drive gear, respectively.

10

1

Share

Can I Test Drive at a 4S Store?

You can test drive at a 4S store. Test Drive Requirements: You can go to a 4S store for a test drive. Bring your driver's license and ID card, fill out the required forms as per the 4S store's requirements, and then you can proceed with the test drive. A staff member will drive the car to the designated test drive route, and then the customer will take over for the driving experience. Liability for Test Drive Consequences: If a traffic accident occurs during the test drive, the driver is fully responsible and must compensate the 4S store as agreed. If the commercial insurance coverage is insufficient for the consequences caused, the driver must bear the additional costs. Test Drive Precautions: During the test drive, please follow the route specified by the dealer and ensure there is a professional accompanying driver to ensure a smooth test drive. Test driving carries certain risks, so before the test drive, make sure to ask whether the car is insured. Only if it is insured can you drive with peace of mind.

7

0

Share

What is the maximum speed limit on urban roads?

For roads without a central dividing line, the maximum speed limit on urban roads is 30 km/h, while on highways it is 40 km/h. For roads with only one motor vehicle lane in the same direction, the maximum speed limit on urban roads is 50 km/h, and on highways it is 70 km/h. Speed must not exceed 30 km/h under the following circumstances: When entering or exiting non-motorized vehicle lanes, passing through railway crossings, sharp curves, narrow roads, or narrow bridges; when making U-turns, turning, or descending steep slopes; when encountering fog, rain, snow, dust, or hail with visibility less than 50 meters; when driving on icy or muddy roads; and when towing a malfunctioning motor vehicle. Speed limit regulations: Motor vehicles must not exceed the speed indicated by speed limit signs or markings on the road. For roads with two or more motor vehicle lanes in the same direction without speed limit signs or markings, the maximum speed limit on urban roads is 70 km/h, while on enclosed motor vehicle-only roads and highways, it is 80 km/h. Special speed limit conditions: Tunnels and tunnel groups generally have a speed limit of 80 km/h. Accident-prone sections typically have a speed limit 20 km/h lower than the main highway speed limit. Sharp curves and interchange ramps are speed-limited according to their design speed. ETC lanes have a speed limit of 20 km/h, and truck weigh-in-motion lanes have a speed limit of 5 km/h.

13

0

Share

What is the APS switch on the car radio?

Why does the brake pedal feel different after a machine brake fluid change?

What are the reasons why the Volkswagen Santana is difficult to start?

Should a Bent Engine Connecting Rod Be Replaced?

What is the basic structure of a motorcycle?

Can I Test Drive at a 4S Store?

What is the maximum speed limit on urban roads?

What are the disadvantages of domestic cars?

Is a Station Wagon a Sedan or an SUV?

How many seconds does the Kawasaki Z1000 take to accelerate from 0 to 100 km/h?

Can Modified Front Bumper Pass Vehicle Inspection?