What is the appropriate tire pressure for the Elysion?

1 Answers
LeVincent
07/29/25 4:49pm
The normal tire pressure range for the Elysion is 2.4-2.5bar. Due to seasonal factors, the tire pressure can be increased by 0.2bar in winter and decreased by 0.1bar in summer. This data is based on the international GBT2978-2008 standard. The Elysion's tire pressure monitoring is a passive function, meaning information will only be displayed on the dashboard if there is an abnormality in the tires. Generally, a tire pressure above 2.8bar is considered too high, while a pressure below 2.0bar is too low. Hazards of overinflated tires: Reduced friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overstretches the tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increased friction with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement of tire parts, causing abnormal heat due to excessive rolling; weakens the function of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction with the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may result in a tire blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes below, and an exclamation mark inside), it is generally due to one of the following three reasons: Abnormal tire pressure: Usually alerts when pressure is below 1.8bar or above 3.0bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset promptly, the system will still record the previous data, causing the indicator light to turn on. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor: The sensor, installed inside the tire and connected to the inflation valve, monitors tire pressure. If the sensor is damaged due to impact while driving, the tire pressure warning light will turn on. In such cases, the only solution is to replace the sensor with a new one.
Was this review help?
7
3
Share
More Forum Discussions

What to Do If Gasoline is Added to a Diesel Generator?

The solution for adding gasoline to a diesel generator is: if the amount is small, no action may be needed; if the amount is large, it should be drained and the fuel tank cleaned. The working principle of a diesel engine is: air is compressed to generate high heat, the engine's fuel injector atomizes and sprays diesel, creating an explosive expansion effect inside the engine to push the piston to work. Diesel engines are divided into: 1. Spark-ignition engines: gasoline engines inject gasoline into the intake pipe, mixing it with air to form a combustible mixture that enters the cylinder and is ignited by the spark plug to burn and expand, performing work; 2. Compression-ignition engines: diesel engines use a fuel injection pump and injector to directly spray diesel into the engine cylinder, where it mixes with compressed air and spontaneously ignites under high temperature and pressure, pushing the piston to perform work.
4
2
Share

Which Pedal is the Brake and Which is the Accelerator?

Brake and accelerator pedals are as follows: automatic transmission vehicles have two pedals, arranged from left to right as the brake pedal and the accelerator pedal; manual transmission vehicles have three pedals, arranged from left to right as the clutch pedal, brake pedal, and accelerator pedal. The function of the brake is to reduce speed or bring the vehicle to a stop. Its working principle involves converting the kinetic energy of the moving vehicle into heat energy through friction between the brake pads and brake drum, as well as between the tires and the road surface, thereby slowing down or stopping the vehicle. The functions of the clutch are: 1. Gradually increasing the driving force of the vehicle to ensure a smooth start; 2. Temporarily separating the engine from the gearbox for gear shifting; 3. Preventing overload in the transmission system; 4. Reducing torsional vibration impacts from the engine, thereby extending the lifespan of the transmission gears.
16
3
Share

What is the replacement interval for brake fluid?

Brake fluid should be replaced every 2 years or 40,000 kilometers. Characteristics of brake fluid: 1. It has good viscosity-temperature properties and a low freezing point, ensuring excellent fluidity at low temperatures; 2. It has a high boiling point, preventing vapor lock formation under high-temperature conditions; 3. It undergoes minimal quality changes, avoiding corrosion or deterioration of metal and rubber components. The replacement procedure for brake fluid is as follows: 1. Park the vehicle on level ground, turn off the engine, open the hood, and drain the fluid from the reservoir; 2. Use a funnel to refill the master cylinder with new brake fluid; 3. Jack up the vehicle and begin by removing the rear wheels; 4. Remove the rubber dust caps from the brake calipers; 5. Loosen the bleeder screws with a wrench, attach a rubber hose, and connect it to a drain bottle; 6. Have someone press the brake pedal inside the vehicle while monitoring the fluid drainage until the reservoir level in the engine compartment reaches the minimum mark.
12
0
Share

Can plug-in hybrid vehicles get green license plates?

Plug-in hybrid vehicles can get green license plates because plug-in hybrid models are classified as new energy vehicles under the national new energy vehicle subsidy policy, and they are different from regular hybrid vehicles. Plug-in hybrid electric vehicles (PHEVs) are a type of new energy vehicle that falls between pure electric vehicles and traditional fuel-powered vehicles. They have both the internal combustion engine, transmission, drivetrain, fuel system, and fuel tank of conventional cars, as well as the battery, electric motor, control circuit, and charging port of pure electric vehicles, with a relatively large battery capacity. Plug-in hybrid electric vehicles enjoy advantages such as subsidies, exemption from traffic restrictions based on license plate numbers, exemption from purchase tax, and lower maintenance costs. Vehicles with green license plates are not subject to tail number restrictions. PHEVs have the benefits of low noise and low emissions. They operate in hybrid mode with the internal combustion engine as the main power source for long-distance travel, while switching to pure electric mode for short-distance trips (such as daily commuting).
3
3
Share

Should You Press the Accelerator or Release the Clutch First After Shifting Gears?

The control of the clutch and accelerator should be synchronized. The correct steps are: release the accelerator, press the clutch, shift gears, slowly release the clutch, and gently apply the accelerator simultaneously. Below are the relevant details: 1. Starting: Press the clutch with your left foot, press the brake with your right foot, shift into first gear, release the handbrake, then slowly release the clutch with your left foot. When the car slightly vibrates, move your right foot to the accelerator pedal and gently apply some throttle while continuing to release the clutch. The car will start smoothly. Once the clutch is fully released with your left foot, apply the throttle to prepare for shifting. 2. Upshifting: Release the accelerator pedal, quickly press the clutch pedal with your left foot, shift the gear lever to the appropriate gear, and release the clutch pedal. While releasing the clutch, slowly press the accelerator with your right foot. 3. Downshifting: First, press the brake to slow down, gently tap the accelerator with your right foot, lift your right foot, quickly press the clutch pedal, shift the gear lever to the appropriate gear, and release the clutch pedal. While releasing the clutch pedal, slowly press the accelerator with your right foot.
10
0
Share

What is the fuel tank capacity of the Honda Elysion?

The fuel tank capacity of the Elysion is 50 liters, as officially announced. Owners who have purchased the Elysion can also check this information on the vehicle's configuration sheet. The Elysion requires 92-octane fuel, with a fuel consumption of 5.9L per 100 kilometers. A full tank can cover a distance of approximately 847 kilometers. During daily driving, it is essential to monitor the remaining fuel level in the tank. This is typically done by observing the fuel gauge inside the vehicle. Under normal circumstances, the fuel level will be accurately reflected on the gauge. The fuel gauge usually has 5 to 6 segments, and it is advisable to refuel when only 2 segments remain to avoid running out of fuel midway. During actual refueling, the amount of fuel added may exceed the marked capacity. This is because the manufacturer's specified tank capacity is measured from the bottom of the tank to the safe fill level, leaving some space from the safe fill level to the tank opening. This space ensures that the fuel can expand when temperatures rise without overflowing. If fuel is added up to the tank opening during refueling, the actual amount of fuel added may exceed the marked tank capacity.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.