What is the actual speed when the display shows 60 mph?

How to Set the Locking Sound for the Tiguan L?

The method to set the locking sound for the Tiguan L is as follows: 1. To turn off the locking horn sound, press and hold the unlock and lock buttons on the remote key simultaneously for 3 seconds until the light flashes once. At this point, the car will only flash its lights without sounding the horn when locked. 2. To restore the horn sound, simply press and hold the lock and unlock buttons simultaneously for 3 seconds until the light flashes once again. Below is an introduction to the Tiguan L: 1. In terms of appearance, the Tiguan L maintains a design similar to the overseas standard Tiguan model, featuring a clean and straightforward overall style. Compared to the standard wheelbase model, it includes additional chrome trim pieces and some changes to the C-pillar design. 2. In terms of configuration, the Tiguan L comes standard with keyless entry, one-button start, electronic parking brake, and many other thoughtful features. The 1.8T model (330TSI) includes standard xenon headlights, automatic headlight activation, LED taillights, roof rails, a multifunction steering wheel, a 4/6 split-folding rear seat, a CleanAir PM2.5 dust filter, automatic rain-sensing wipers, keyless start, engine auto start-stop, an electronic parking brake with auto-hold function, rear parking sensors/camera, and heated exterior mirrors. 3. In terms of power, the new Tiguan L offers two engine options: the 330TSI and 380TSI, equipped with a 1.4T and a 2.0T turbocharged engine respectively. The former delivers a maximum output of 110kW and a peak torque of 250N•M, while the latter offers a maximum output of 137kW and a peak torque of 320N•M.

4

3

Share

How to Release the Parking Brake on a Mercedes-Benz?

Mercedes-Benz vehicles with foot-operated parking brakes require manual assistance for release: There is a handle on the left side of the steering wheel; pulling it by hand will release the foot-operated parking brake. Below are the steps for using the parking brake: 1. To engage the parking brake, press the brake pedal downward and pull the parking brake lever upward completely. To release the parking brake, press the brake pedal downward, slightly pull the parking brake lever upward, press the button on the end of the handle with your thumb, and then lower the parking brake lever back to its original position. 2. For vehicles equipped with an automatic transmission, always apply the parking brake first before shifting the gear lever to the "P" (Park) position. When parking on an incline, if you shift to "P" first and then engage the parking brake, the weight of the vehicle may make it difficult to shift out of "P" when preparing to drive. 3. When preparing to drive, shift the gear lever out of "P" before releasing the parking brake. 4. Do not engage the parking brake while driving, as this may cause overheating, reduce the effectiveness of the rear brakes, shorten the brake's lifespan, or cause permanent damage. 5. If the parking brake cannot hold the vehicle securely or does not fully release, immediately have it inspected by a dealer or service center. Before leaving the vehicle, always fully engage the parking brake to prevent the vehicle from moving, which could cause injury or damage. 6. When parking, ensure the gear lever of a manual transmission vehicle is in neutral. For automatic transmission vehicles, place the gear lever in the "P" (Park) or "N" (Neutral) position. Most automatic transmission vehicles only allow the ignition key to be removed when in "P." Except under special circumstances, strictly avoid parking with the transmission in a forward gear (D, S, L, or with Arabic numerals) or reverse (R) position.

19

2

Share

What does fault code 00546 mean?

Here are the solutions for fault code 00546: 1. Clean the throttle body and check if G188 is functioning properly; 2. If it works normally, then the engine wiring harness needs to be replaced. Below is more information about the throttle body: 1. Components: The throttle body unit contains two sensors - angle sensor 1-G187 and angle sensor 2-G188. 2. Function: These sensors determine the current position of the throttle valve and transmit this information to the engine control unit. The engine control unit uses the angle sensor signals to determine the throttle valve's position.

3

Share

What is the principle of yielding when turning?

The principle of yielding when turning is to yield to vehicles coming from the right, yield to vehicles going straight, and yield to left-turning vehicles when turning right in opposite directions. The following is an introduction to traffic violations: 1. Definition: Traffic violations refer to acts by vehicle drivers, pedestrians, passengers, and other individuals or units related to road traffic activities that violate the "Road Traffic Safety Law of the People's Republic of China" and related laws, regulations, and traffic management rules. 2. Hazards: Traffic violations lead to disorder in traffic, cause accidents, affect the city's appearance, and create public hazards.

20

5

Share

How to Upgrade the Buick In-Car System?

To upgrade the Buick in-car system, you need to download the corresponding system from the Buick official website, save it to a USB flash drive, and then proceed with the installation upgrade. The Buick IntelliLink intelligent in-car interaction system is not only an auxiliary system for car driving but also another mobile platform connecting people and the internet, following mobile computers and 3G phones. Buick is an automobile brand under General Motors, known for its high horsepower, individuality, practicality, and maturity. Buick includes many well-known models such as Excelle, Regal, LaCrosse, GL8, as well as the Rendezvous, Enclave, and Encore.

11

0

Share

What is the purpose of wheel balancing?

Wheel balancing enhances driving comfort, reduces fuel consumption, extends tire lifespan, ensures straight-line stability of the vehicle, and minimizes wear on chassis suspension components. Introduction to Wheel Balancing: Wheel balancing is generally considered as the balance between wheels when the vehicle is in motion. It typically involves the installation of balancing weights. Principle of Wheel Balancing: Due to manufacturing imperfections, when car wheels rotate at high speeds, they can cause wheel wobbling and steering wheel vibration during driving. To prevent or eliminate this phenomenon, weights are added to the wheels in a dynamic state to correct the balance at various edges. This correction process is commonly referred to as wheel balancing.

3

Share

What is the actual speed when the display shows 60 mph?

How to Set the Locking Sound for the Tiguan L?

How to Release the Parking Brake on a Mercedes-Benz?

What does fault code 00546 mean?

What is the principle of yielding when turning?

How to Upgrade the Buick In-Car System?

What is the purpose of wheel balancing?

What is the fuel tank capacity of the Leiling 1.2T in liters?

Should Polo Use 92 or 95 Octane Gasoline?

How Many Kilometers Can a Yaris L Run on a Full Tank of Gas?

What grade of gasoline should be used for the CB400X?