What is the actual measured ground clearance of the Honda CR-V?

1 Answers
AlexisAnn
07/30/25 6:07am
The actual measured ground clearance of the Honda CR-V when unloaded is 198mm for the two-wheel-drive version and 208mm for the four-wheel-drive version. Relevant information about ground clearance: 1. Ground clearance refers to the distance between the ground and the rigid object at the bottom of the vehicle. The ground clearance of a vehicle varies depending on whether it is unloaded or loaded. 2. Ground clearance is related to the vehicle's load; the heavier the load, the smaller the ground clearance. Vehicles with small ground clearance have a lower center of gravity but poor off-road capability. Vehicles with large ground clearance have good off-road capability and higher ground clearance, making it easier to park on curbs or other parking spaces with height differences.
Was this review help?
19
3
Share
More Forum Discussions

Which car brand features a lion emblem?

A car with a lion emblem represents the Dongfeng Peugeot brand, which is part of the Shenlong Automobile Co., Ltd. Its lineup includes models such as the Peugeot 4008 New Energy, Peugeot 408, Peugeot 508, Peugeot 4008, and Peugeot 5008. Taking the Peugeot 508 as an example, its body dimensions are: 4870mm in length, 1855mm in width, and 1455mm in height, with a wheelbase of 2848mm, a trunk capacity of 513 liters, and a curb weight of 1490kg. The Peugeot 508 features a MacPherson strut front suspension and a multi-link independent rear suspension. It is powered by a 1.6T turbocharged engine, delivering a maximum horsepower of 170PS, a maximum power of 125kW, and a maximum torque of 250Nm, paired with a 6-speed automatic transmission.
18
3
Share

Where is the Porsche VIN located?

The Porsche VIN is located on the nameplate at the upper left corner of the engine under the hood. Porsche models include: Porsche 911, Porsche 718, Taycan, Cayenne, Cayenne New Energy, etc. Taking the 2020 Cayenne as an example, its body dimensions are: length 4918mm, width 1983mm, height 1696mm, with a wheelbase of 2895mm and a fuel tank capacity of 90L. The 2020 Cayenne features a multi-link independent front suspension and a multi-link independent rear suspension. It is equipped with a 2.9T naturally aspirated engine, delivering a maximum horsepower of 440PS, a maximum power of 324kW, and a maximum torque of 550Nm, paired with an 8-speed automatic manual transmission.
15
4
Share

Where is the fender located?

The fender is located at: 1. Above the front tires, between the front door, hood, and bumper; 2. Above the rear tires and behind the rear door. The function of the fender is: utilizing fluid dynamics to reduce the drag coefficient, making the vehicle run more smoothly. The fender is also called a wing panel, and can be divided into front fender and rear fender according to its position. The replacement method is: 1. Support the chassis with a jack, then remove the tire; 2. Remove the screws or clips fixing the fender liner, and take off the fender; 3. Clean the mud and sand under the fender, and install the new fender.
17
3
Share

What is the Function of Brake Fluid?

Brake fluid functions to transmit energy, dissipate heat, prevent corrosion and rust, as well as provide lubrication. The method to determine when brake fluid needs replacement is: when the water content in the brake fluid reaches 3%, it must be replaced immediately. The steps to replace brake fluid are: 1. Park the vehicle on level ground and turn off the engine, then open the hood and drain the remaining brake fluid; 2. Use a funnel to fill the reservoir with new brake fluid; 3. Press the brake pedal inside the car until the fluid level in the reservoir under the hood reaches the lower limit. Precautions for using brake fluid: 1. Avoid mixing with gasoline or engine oil; 2. Replace it regularly; 3. Choose high-quality brake fluid.
17
2
Share

What Does Brake Pad Wear Mean?

Brake pad wear refers to the severe deterioration of a vehicle's brake pads, at which point the warning light on the dashboard will illuminate, indicating the need for immediate replacement. The method for replacing brake pads is as follows: 1. Open the engine compartment and check the brake fluid level to prevent overflow during the replacement process; 2. Remove the wheel where the brake is located; 3. Unscrew the bolts of the brake caliper and remove the brake pads; 4. Install new brake pads, tighten the guide bolts, and complete the replacement. The working principle of brake pads is to utilize the friction between the brake pads and the brake drum, as well as between the tires and the ground, converting the kinetic energy of the moving vehicle into heat energy through friction, thereby bringing the car to a stop.
11
2
Share

What is the Difference Between a Sunroof and a Moonroof?

The differences between a sunroof and a moonroof are as follows: 1. Opening capability: A moonroof is made of a single piece of glass and cannot be opened, thus it does not provide ventilation; a car sunroof can be opened, allowing effective air circulation and bringing in fresh air. 2. Maintenance costs: The maintenance cost for a moonroof is lower than that for a sunroof. Below is the classification of sunroofs and moonroofs: 1. Moonroofs are categorized by opening type: fixed, sectional opening, and full opening. Car sunroofs can be broadly divided into: pop-up, sliding, tilt/slide, panoramic, and curtain types.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.