What is the actual fuel consumption of the Tiggo 3?

1 Answers
RonanRose
07/30/25 3:21am
Tiggo 3 has a total of 7 models. The Tiggo 3 2022 Classic Value Edition includes 5 models equipped with a 116-horsepower engine: 1.5L Manual Fashion, Premium, Luxury, Fashion, and Elite, with an NEDC fuel consumption of 7.3L per 100km. The Tiggo 3 2022 Classic Value Edition also includes 2 models equipped with a 156-horsepower engine: 1.5T CVT Premium and CVT Elite, with an NEDC fuel consumption of 7.2L per 100km. The fuel tank capacity is the same for all Tiggo 3 models. The distance that can be covered on a full tank is as follows: For models with a 116-horsepower engine, the fuel tank capacity is 55L, and the distance on a full tank is 55/7.3*100=753km. For models with a 156-horsepower engine, the fuel tank capacity is 55L, and the distance on a full tank is 55/7.2*100=764km. Vehicle fuel consumption is directly influenced by five major factors: driving habits, the vehicle itself, road conditions, natural wind, and ambient temperature. Specific factors that increase fuel consumption include: Driving habits: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before a red light can increase fuel consumption. The vehicle itself: Vehicles with larger engine displacements generally consume more fuel because higher displacement usually means higher power output, requiring more gasoline for combustion. Heavier vehicles also consume more fuel due to the need for greater driving torque. Road conditions: Driving on unpaved roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases vehicle resistance and fuel consumption. Low ambient temperature: When the engine block is cold, injected gasoline does not atomize easily, requiring more gasoline for combustion, which increases fuel consumption. Additionally, in low temperatures, the engine control unit may increase idle speed to warm up the engine, further raising fuel consumption.
Was this review help?
2
2
Share
More Forum Discussions

What does variable suspension adjustment mean?

Variable suspension adjustment refers to the ability to manually or automatically change the height or stiffness of the suspension to adapt to different road conditions. Below is a related introduction: Features of adjustable suspension: Unlike traditional suspension systems, variable suspension allows the driver to manually or the vehicle to automatically adjust the height and stiffness of the suspension to handle various road conditions, keeping the vehicle in optimal state at all times. However, due to its high cost, it is only found in some high-end vehicles. Adjustable suspension: Suspension height adjustment means the vehicle adjusts the ground clearance based on speed and related sensors. Some vehicles have control buttons on the center console, allowing the driver to actively operate according to road conditions, while others automatically lower or raise the suspension based on driving conditions.
17
0
Share

What is the wading depth for motorcycles?

The height of the motorcycle's air intake determines its wading depth. Below are relevant details about motorcycle wading: Hazards of water ingress while riding: The main components prone to water ingress are the vehicle's fuel supply system and electrical control system, followed by the engine, ignition system, generator, and fuel tank. Water infiltration into the fuel supply system includes the carburetor and air filter. Issues with carburetor water ingress: This primarily occurs when water flows down the throttle cable or due to poor sealing of the fuel tank cap, allowing water to leak into the fuel tank and mix with gasoline before entering the carburetor. Particularly, if the sealing rubber sleeve at the carburetor's throttle cable port ages and cracks, water can easily seep in. If damaged, it should be replaced as soon as possible.
1
4
Share

Does sand blowing into the intake pipe when replacing the air filter have any impact?

It does have an impact. Air intake filtration primarily relies on the air filter. If there is sand or other debris in the pipeline, it can directly enter the engine cylinders, leading to cylinder scoring. Therefore, regularly replacing the air filter is crucial, and other impurities must also be cleaned promptly. Below is a relevant introduction: Hazards: During operation, the engine inhales a large amount of air. If the air is not filtered, the suspended dust in the air can enter the cylinders, accelerating the wear of the piston group and the cylinders. Larger particles entering between the pistons and cylinders can cause severe "cylinder scoring," which is particularly serious in dry and sandy working environments. The air filter is installed in front of the carburetor or intake pipe to filter out dust and sand particles from the air, ensuring that sufficient and clean air enters the cylinders. Types of air filters: They can be divided into filtration type, centrifugal type, oil bath type, and composite type.
7
0
Share

What Does Automotive Sheet Metal Technology Mean?

Automotive sheet metal (Metal-Plate) is a technical method in automobile repair, where automotive sheet metal is equivalent to automotive sheet metal repair. It refers to all the work required to restore a vehicle's body after a collision, excluding the anti-corrosion and decorative spray painting of the body. Below is a relevant introduction: Introduction: Automotive sheet metal is a processing method in automobile repair, also known as cold working. Simply put, if the vehicle's exterior is damaged or deformed, the sheet metal process is necessary. Automobile collision repair has evolved from the original 'hammering, pulling, welding, and patching' to the secondary manufacturing and assembly of the vehicle body. Material Requirements: Sheet metal materials must have excellent plasticity. They must possess the ability to undergo permanent deformation under external forces without being destroyed. For cold-worked parts, good cold plasticity is required, such as automotive stamping parts; for hot-worked parts, good hot plasticity is necessary, such as hot-forged spring steel plates and hot-riveted rivets.
10
2
Share

Do 8-year-old vehicles exempt from inspection still need to apply for the annual inspection sticker?

Vehicles in their eighth year are not exempt from inspection and require an on-site inspection at the vehicle management office before obtaining the annual inspection sticker. Therefore, for an eight-year-old vehicle, you should schedule an inspection at the vehicle management office within three months before the inspection expiration date. Alternatively, you can follow the legal dates suggested by the traffic management app 12123 to arrange the inspection. Below are the relevant details: Inspection schedule: Vehicles older than six years no longer qualify for the six-year exemption from on-site inspections. They must undergo an inspection at the vehicle management office every two years after reaching six years of age. After ten years, an annual inspection is required. Once the vehicle passes the inspection at the designated testing station, it will receive an inspection compliance sticker. Consequences of skipping inspection: Missing the inspection deadline places the vehicle in an unregistered status, making it illegal to drive. If caught by traffic police, the owner will face penalties and demerit points. Therefore, it is crucial to complete the inspection on time, especially for vehicles older than six years. Vehicles that fail to undergo inspection for three consecutive cycles will enter the mandatory scrapping process, rendering them unusable. If discovered by traffic police, they will be directly processed for scrapping.
15
2
Share

Which Gear Should Be Used for Climbing Hills?

Which gear to use for climbing hills depends on the type of vehicle: For manual transmission cars, you can use 2nd or 3rd gear when climbing hills; for automatic transmission cars, you can use the S (Sport) or L (Low) gear, or simply the D (Drive) gear. Below are the relevant details: Manual Transmission Cars: A manual transmission car uses a manual gear-shifting mechanical transmission to adjust speed. The driver must manually shift the gear lever to change the gear engagement inside the transmission, altering the gear ratio to achieve speed changes. The gear lever can only be moved when the clutch is depressed. Automatic Transmission Cars: An automatic transmission car does not require the driver to manually shift gears. The vehicle automatically selects the appropriate gear based on driving speed and traffic conditions.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.