What is the actual fuel consumption of the Envision 2.0t?

1 Answers
LaMorgan
07/25/25 7:28am
The fuel consumption of the Envision Plus ranges from 7.4 to 7.8L. Neglecting engine maintenance leads to higher fuel consumption: Abnormalities in the engine ignition system significantly impact fuel consumption. Issues such as inaccurate ignition timing, leaking high-voltage wires, or weak ignition due to spark plug carbon buildup can reduce engine combustion efficiency and increase fuel consumption. Additionally, poor engine maintenance can lead to a 10% to 20% increase in fuel consumption, which is considered normal. Using the trunk as storage increases fuel consumption: There is a direct correlation between vehicle weight and fuel consumption. It is said that for every 10% reduction in vehicle weight, fuel consumption decreases by a corresponding percentage.
Was this review help?
1
0
Share
More Forum Discussions

How often should the timing chain of the Peugeot 1.6T engine be replaced?

The timing chain of the Peugeot 1.6T engine does not require replacement and is designed for lifetime maintenance-free operation. Below are the specific details about the timing chain: 1. Function: The engine timing chain drives the valve train mechanism, ensuring that the engine's intake and exhaust valves open and close at the correct times to allow normal air intake and exhaust in the cylinders. In some models, such as the Volkswagen Jetta, Bora, and Audi, it also drives the water pump. 2. Effects of Timing Chain Stretching: Unlike timing belts, timing chains are less prone to breakage or deformation. However, being made of metal, they can stretch, wear, and develop increased gaps under high-speed engine operation. If the timing chain stretches due to increased gaps, it can lead to inaccurate timing and increased noise. If the timing chain wears or stretches due to aging, causing timing misalignment, the valve stems may bend, piston tops may dent, and in severe cases, the cylinder head could be damaged, rendering the engine inoperable.
14
2
Share

What is the fuel consumption of the Cayenne?

The fuel consumption of the Cayenne ranges from 8.9L to 15.7L. Taking the 2021 Cayenne Turbo GT as an example: it is a mid-to-large-sized 5-door, 4-seat SUV equipped with an 8-speed automatic transmission. Its dimensions are 4942mm in length, 1995mm in width, and 1636mm in height, with a wheelbase of 2895mm. The top speed reaches 300 kilometers per hour. The 2021 Cayenne Turbo GT uses a 4.0T twin-turbocharged engine, with a maximum torque of 850 Nm and a maximum horsepower of 640 hp. The fuel tank capacity is 90L, the drivetrain is front-engine four-wheel drive, the front tire specification is 285/35R22, and the rear tire specification is 315/30R22.
7
4
Share

What is the Function of the Cylinder Block?

About the function of the cylinder block, the cylinder block is the main body of the engine, connecting the cylinders and the crankcase into one unit. It serves as the supporting framework for installing pistons, crankshafts, and other components and accessories. Here is additional information: 1. Performance: It must have sufficient strength and stiffness with minimal deformation to ensure the correct positioning of moving parts, normal operation, and low vibration and noise. It should also have good cooling performance, with cooling water jackets around the cylinder bores to allow cooling water to carry away heat. Additionally, it must be wear-resistant to ensure the cylinder block has a long service life. 2. Composition: The upper part of the cylinder block consists of parallel cylinder bores, most of which are now fitted with cylinder liners. The lower part of the cylinder block is the crankcase, which houses the crankshaft and can also accommodate various accessories such as generators and engine mounts externally. Most cylinder blocks are cast from cast iron or aluminum alloy. Aluminum alloy blocks are more expensive but offer advantages like lighter weight and better cooling performance, making them increasingly popular.
12
3
Share

What Are Common Vehicle Malfunctions and Their Repairs?

Here is an introduction to common vehicle malfunctions and their repairs: Dead Battery: A dead battery can result from two causes—either the battery has reached the end of its lifespan or has malfunctioned, or the headlights were left on, causing a power drain. You can start the vehicle using one of the following three methods: towing or pulling by another vehicle; borrowing power from another vehicle; or using a downhill slope to start the engine. To jump-start the battery using jumper cables, follow these steps: Prepare two relatively thick wires (usually red and black if purchased from the market). Connect one end of the red wire to the positive terminal of the charged battery and the other end to the positive terminal of the dead battery. Connect one end of the black wire to the negative terminal of the dead battery and the other end to a metal part of the charged vehicle. Start the charged vehicle first to help the dead vehicle start. Note: The donor vehicle should be running. Connect the positive terminal first, then the negative terminal. After starting, disconnect the negative terminal first, then the positive terminal. This prevents accidental contact between the positive terminal and the vehicle body, which could cause a short circuit. Low Oil Warning: If the oil warning light (red) turns on and it’s not due to a sensor malfunction, it usually means the engine is low on oil. Continuing to drive with insufficient oil can lead to severe damage, such as pistons breaking the cylinder block, causing sudden engine shutdown. This is not only dangerous but also results in high repair costs. If a fuel tank leak occurs due to accidental impact and no repair shop is nearby, you can chew gum and press it onto the leak. Once dried, the gum can temporarily seal the leak, serving as an emergency fix. Tire Blowout: A tire blowout is an unexpected and dangerous situation while driving at high speeds. If a blowout occurs, stay calm, avoid sudden steering movements, and firmly grip the steering wheel to maintain control while gradually slowing down. After safely stopping, set up a warning triangle behind the vehicle to prevent secondary accidents, then replace the tire with the spare.
18
0
Share

What are the pros and cons of 21-inch wheels for the Cayenne?

Here are the detailed pros and cons of 21-inch wheels for the Cayenne: 1. Advantages: (1) Stronger load-bearing capacity: Small wheels usually use steel materials to save costs, but large wheels are made of aluminum alloy, especially those produced by forging processes. The load-bearing capacity of such wheels is five times that of ordinary steel wheels. (2) Improved cornering performance: After wheel modification, the contact area increases, enhancing the vehicle's stability during cornering and significantly improving its cornering performance. 2. Disadvantages: (1) Reduced vehicle performance: Large-size wheels affect acceleration and braking performance. As the wheel size increases, the width also increases accordingly. Larger and wider wheels naturally have greater weight, requiring more power consumption to drive them, which impacts acceleration performance. (2) Increased fuel consumption: Large wheels have an advantage in diameter, and the corresponding tread width is also larger. The benefit is that the increased contact area between the wheels and the road surface enhances grip, but the trade-off is increased friction, leading to a certain degree of higher fuel consumption.
3
1
Share

How high can high heels be when driving?

According to traffic safety regulations, it is prohibited to drive while wearing slippers or high heels with heels of 4cm or more, barefoot, or talking on the phone while holding it. Violators will be penalized with 2 demerit points and a certain fine. High heels with 3cm heels are technically allowed for driving, but wearing such shoes may be considered as skirting the edge of the regulations. For safety reasons, it is recommended to wear flat shoes or sneakers when driving. High heels can easily get stuck: Because the heel is too high (over 4cm), when the driver tries to step on the brake or accelerator, the heel can easily get stuck in the gap between the pedal (brake pedal) and the car floor, making it difficult to press the pedal properly and seriously affecting normal driving. When switching between the accelerator and brake pedals, the heel can easily get stuck during the transition. Improper stepping: Wearing shoes with overly thick soles, such as platform shoes or height-increasing shoes, weakens the foot's perception of pedal depth, leading to excessive acceleration or deceleration.
2
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.