What is the actual fuel consumption of the 1.8 Civic?

What are the symptoms of a faulty timing chain in a Magotan?

A faulty timing chain can cause abnormal engine noises, increased fuel consumption, higher oil consumption, failure to start the car, insufficient power, and severe exhaust emissions. How to check the timing chain: 1. Use a spring scale to measure the elongation of the chain at three or more points. If it exceeds the permissible length, it should be replaced promptly. 2. Use a vernier caliper to monitor the thickness of the tensioner and the chain damper. If they exceed the wear limit, they should be replaced immediately. 3. Inspect the timing chain for elongation, wear, or breakage. If there is even minor damage, it should not be used further.

9

3

Share

How to use the roof rack of Haval H6?

Haval H6 roof rack usage method is: 1. Cargo or luggage should be tightly fastened or secured on the roof rack, and evenly distributed; 2. During driving, emergency braking should be avoided as much as possible; 3. The load-bearing design of the roof rack is generally 30 to 50 kilograms, and the weight of objects should not exceed the designed load-bearing capacity when in use. The Haval H6 is a compact urban SUV with body dimensions of 4600mm in length, 1860mm in width, and 1720mm in height, with a wheelbase of 2680mm. In terms of power, the Haval H6 is equipped with a 1.5T turbocharged engine, with a maximum power of 124kw and a maximum torque of 285nm, matched with a 7-speed dual-clutch transmission.

8

5

Share

Where is the Cruze radiator located?

Radiator location: Inside the engine compartment, positioned directly behind the front grille of the vehicle. Functions of the radiator: 1. As a crucial component of the water-cooled engine's cooling circuit, it absorbs heat from the engine block to prevent overheating. 2. It uses water as a heat transfer medium to conduct heat, then dissipates it through convection via large-area cooling fins to maintain the engine's optimal operating temperature. The new Cruze offers two powertrain options: (1) The 1.4T model delivers a maximum output of 110kW (150PS) with peak torque of 240N•m, paired with a 7-speed DCG dual-clutch transmission. (2) The 1.5L model produces a maximum output of 84kW (114PS) with peak torque of 146N•m, mated to either a 6AT automatic transmission or 6MT manual transmission.

15

4

Share

Where is the air conditioning filter located in the Mondeo Zhisheng?

The air conditioning filter in the Mondeo Zhisheng is installed on the right side of the accelerator pedal in the driver's seat. Steps to replace the Mondeo air conditioning filter: 1. First remove the accelerator pedal for replacement. 2. Open the front passenger door, then open the glove compartment and carefully pry open the trim panel next to it. 3. This trim panel uses a snap-fit design and can be opened with slight force - be careful not to use excessive force. 4. Unscrew the 4 screws on the glove compartment and set them aside. 5. Use your foot to support the removed glove compartment (as there are small light wires connected behind it), then open the clips on both sides of the air conditioning filter cover and pull out the old filter. 6. Install the new filter (pay attention to the direction marked on the filter).

15

3

Share

What are the characteristics of the coolant temperature sensor?

Characteristics of the coolant temperature sensor: The engine ECU receives the signal from the coolant temperature sensor as a correction signal for fuel injection and ignition. By utilizing the coolant temperature sensor, drivers can promptly identify and address issues. Below is an introduction to the temperature sensor: 1. The coolant temperature sensor is installed in the engine block water jacket or coolant pipeline, in contact with the coolant, to detect the engine's coolant temperature. After receiving this temperature signal, the ECU adjusts the fuel injection timing and ignition timing. 2. The slender head of the engine coolant temperature sensor is in contact with the coolant, containing a negative temperature coefficient thermistor inside. Upon receiving the signal from the coolant temperature sensor, the ECU adjusts the fuel injection timing and ignition timing of the engine.

1

5

Share

What transmission does the Geely Emgrand use?

Geely Emgrand uses two types of transmissions in total, one is a 5-speed manual transmission, and the other is a CVT transmission. Here is some information about the CVT transmission: 1. The structure of the CVT transmission is very simple. This transmission only has two cone wheels and a steel belt. The steel belt of this transmission can move on the cone wheels, allowing the transmission to change speed and torque. The CVT transmission has good reliability and durability, and its shifting smoothness is also excellent. During the shifting process, the CVT transmission hardly has any jerking. 2. The disadvantage of the CVT transmission is that it cannot be used with high-power engines. The torque that this transmission can withstand is relatively small. If used with high-power engines, the steel belt of the CVT transmission may slip.

11

5

Share

What is the actual fuel consumption of the 1.8 Civic?

What are the symptoms of a faulty timing chain in a Magotan?

How to use the roof rack of Haval H6?

Where is the Cruze radiator located?

Where is the air conditioning filter located in the Mondeo Zhisheng?

What are the characteristics of the coolant temperature sensor?

What transmission does the Geely Emgrand use?

Can temporary license plates use ETC?

What does a 6-pack of gasoline additive mean?

What is protech tire

When is the ETC fee deducted after passing the highway?