What is the acceleration time of the Mazda 3 1.5?

1 Answers
StGrace
07/29/25 11:44am
The Mazda 3 1.5 accelerates from 0 to 100 km/h in approximately 12 seconds. The 0-100 km/h acceleration time is a direct reflection of a car's power. Taking the 2020 Mazda 3 as an example, its body dimensions are: length 4662mm, width 1797mm, height 1445mm, with a wheelbase of 2726mm and a fuel tank capacity of 50 liters. The 2020 Mazda 3 is equipped with a 1.5L naturally aspirated engine, delivering a maximum power of 86kW and a maximum torque of 148Nm, paired with a 6-speed manual transmission. It features a MacPherson strut front suspension and a torsion beam rear suspension.
Was this review help?
20
5
Share
More Forum Discussions

Is ABS a Must for Beginners Buying Motorcycles?

Beginners buying motorcycles do not necessarily need ABS. Relevant information is as follows: 1. Introduction: ABS refers to the Anti-lock Braking System in the braking system, which automatically controls and adjusts the braking force on the wheels, mainly to prevent skidding, spinning, fishtailing, and loss of directional control during emergency braking. 2. Function: It enables the shortest distance stable stop. It controls the vehicle's slip ratio, which is the difference between the vehicle body speed and the wheel speed divided by the vehicle body speed, expressed as a percentage. The formula is s = (v - rw)/v × 100%. A slip ratio of 0 indicates free rotation of the wheels.
6
3
Share

Reasons for Water Accumulation in the Main Driver's Compartment

Here are the reasons for water accumulation in the main driver's compartment: 1. Not closing the window during rainy days: After getting out of the car, failing to confirm whether the main driver's side window is tightly closed can allow rainwater to enter the main driver's compartment. Over time, this can lead to water accumulation under the main driver's compartment. 2. Issues with drainage outlets: If water continues to drip under the driver's compartment after ruling out human factors, it is necessary to inspect the car's drainage outlets. There are four drainage outlets in total—the front two are for sunroof drainage, while the rear two are for draining water flowing on the car.
11
4
Share

How to Use the Gears of a CVT Car?

P stands for Parking gear, used when parking (when turning off the engine and during prolonged idling). R stands for Reverse gear. In this gear, the transmission will automatically switch between gears 1 to 5 based on speed and throttle conditions. S stands for Sport mode. In this gear, the transmission can shift freely, but the shifting timing will be delayed. It should mean the same as the 1 in the new Accord. In this gear, the transmission will stay in 1st gear without upshifting. The snowflake button is for starting on slippery roads. When this button is pressed, the vehicle will start from 2nd gear instead of 1st gear.
4
4
Share

What causes the rear axle noise in Pajero V73?

Pajero V73 rear axle noise causes are detailed as follows: Improper tooth side clearance: Noise from improper tooth side clearance. When the preload of the main reducer bearings is normal, a metal impact sound occurs at the rear axle shortly after starting the car or during gear shifting. As the speed stabilizes, the impact sound turns into continuous noise. When the throttle changes abruptly, an irregular noise appears at the rear axle, which is generally caused by excessive tooth side clearance. Bearing wear: While driving, if the noise increases with higher speed and decreases or disappears when coasting, it is usually due to bearing wear or abnormal gear clearance. If the noise occurs when abruptly changing speed or going uphill, it indicates excessive gear meshing clearance.
7
3
Share

How to Reset the Maintenance Light on a 2020 Civic?

First, press the "A" button and hold down the brake pedal. Note that neither should be released midway. Then, turn the power to the "ON" position without starting the engine. Characters will flash or the display will blink. Next, continue holding the "A" button without releasing it. An ellipsis ("...") will appear on the screen. After that, release the reset button "A" and let go of the brake. Finally, turn the ignition switch back to the "Off" position to complete the reset process.
12
0
Share

How to Turn On/Off the Rear Wiper of Volvo XC90?

Enter the driver's cabin and you can see the wiper control lever located on the right side behind the steering wheel. The wiper control lever is marked with corresponding function indicators. The three upper positions on the left side are the speed adjustment gears for the front wiper. The two upper and lower positions on the right side are the spray gears for the front wiper and rear wiper, respectively. The second position from the top is the gear to turn on the rear wiper. Finally, the "OFF" position on the right is the gear to turn off the rear wiper. After switching it backward, the wiper will neither wipe nor spray water.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.