What is the 0-100km/h acceleration time of the Xingyue 1.5T?

1 Answers
McGemma
07/30/25 10:32am
Xingyue 1.5T achieves a 0-100km/h acceleration time of approximately 9 seconds. Taking the 2020 High-Energy Edition Ruixingzhe Xingyue 1.5T as an example, the relevant specifications are as follows: Body Dimensions: The vehicle measures 4605mm in length, 1878mm in width, and 1643mm in height, with a wheelbase of 2700mm. It has a curb weight of 1530kg and a trunk capacity of 326L. Powertrain: Equipped with a 1.5L turbocharged 3-cylinder JLH-3G15TD engine, delivering a maximum horsepower of 177Ps, peak power of 130KW, and maximum torque of 255N·m. It is paired with a 7-speed wet dual-clutch transmission. Chassis: The drivetrain configuration is front-engine, front-wheel drive. It features MacPherson strut front suspension and multi-link independent rear suspension, utilizing a unibody structure.
Was this review help?
7
4
Share
More Forum Discussions

Is the Audi A6 Front-Wheel Drive or Rear-Wheel Drive?

The Audi A6 is a front-wheel-drive vehicle, featuring a front-engine, front-wheel-drive layout where the engine is positioned at the front of the car, and the front wheels drive the entire vehicle. More details about the Audi A6 are as follows: 1. The dimensions of the domestic version of the Audi A6 are 5038 mm in length, 1886 mm in width, and 1475 mm in height, with a wheelbase of 3024 mm. 2. The Audi A6 is equipped with three engines: a low-power 2.0-liter turbocharged engine, a high-power 2.0-liter turbocharged engine, and a 3.0-liter turbocharged engine. 3. The low-power 2.0-liter turbocharged engine delivers a maximum power of 190 horsepower and a maximum torque of 320 Nm; the high-power 2.0-liter turbocharged engine produces a maximum power of 224 horsepower and a maximum torque of 350 Nm; the 3.0-liter turbocharged engine generates a maximum power of 340 horsepower and a maximum torque of 500 Nm.
6
3
Share

Will I be penalized for driving 105 in a 100 km/h speed limit zone?

No, you won't be fined as it doesn't exceed 10% of the speed limit. Here are some long-distance driving precautions: 1. Pre-trip inspection: Before your journey, thoroughly check all vehicle components, tires, lights, fluids, wipers, etc. Especially for long highway trips, pay special attention to tire conditions and address any issues immediately, as a blowout on the highway can be extremely dangerous. Take breaks every 2 hours of continuous highway driving to adjust your condition, and let your vehicle rest too - this ensures safety for the next leg of your trip. 2. Speed control: Slow down, observe carefully, and proceed cautiously. While this advice may sound repetitive, it's genuinely life-saving. The saying "Nine out of ten accidents are caused by speeding" holds true. To reduce accident risks and improve survival chances, maintain appropriate (but not excessively slow) speeds according to regulations. Particularly when exiting highways via ramps, consciously reduce speed as many drivers tend to overspeed in these sections. 3. Avoid frequent lane changes: Most highways have three lanes. As a rule, don't occupy the passing lane or slow lane for extended periods - the middle lane is generally safest as it provides more space on both sides. If accidents occur with vehicles on either side or ahead/behind, the middle lane allows more reaction time. Unless necessary, avoid frequent lane changes as they cause many accidents. When overtaking or changing lanes, always signal for at least 3 seconds before maneuvering. 4. Keep distance from large vehicles: Maintain distance from trucks due to their large blind spots and heavy weight. Trucks require longer braking distances and often can't see smaller vehicles in their blind spots, making accidents more likely. In any collision, passenger vehicles typically sustain more damage than trucks. Never drive too close to large trucks, especially avoid driving parallel to them. When encountering trucks, overtake decisively if possible.
3
3
Share

What is Tesla's Charge Limit?

Tesla's charge limit refers to setting the maximum charging level for the battery. Setting a charge limit prevents the battery from being fully charged, thereby extending its lifespan. Additionally, when charging outside but with limited funds on your phone, setting a charge limit can help avoid overcharging. The Tesla mobile app and the vehicle's touchscreen both allow you to adjust the charge limit. Method to Adjust Tesla's Charge Limit: On the touchscreen, tap the battery icon to bring up the charging settings interface; click the [Set Limit] button, then drag the arrow on the upper graphic. For daily use, the leftmost tick mark represents 50%, with each increment being 10%, while the rightmost tick mark for long trips represents 100%; click [Done] to complete the setup. Reason Why the Charge Limit Keeps Changing: Some owners have reported that Tesla's charge limit keeps changing. This is because the system calculates the charge limit by dividing the current range by the battery percentage, which can result in slight inaccuracies.
11
4
Share

How to Adjust the Fuel Supply Angle of a Four-Cylinder Diesel Engine?

The steps to adjust the fuel supply angle of a four-cylinder diesel engine are as follows: 1. Remove the high-pressure fuel pipe of the first cylinder and connect a thin transparent small rubber tube to the outlet of the fuel injection pump. Place the throttle in the maximum position and rotate the crankshaft to eliminate air from the fuel line. Then, squeeze a few drops of oil from the small rubber tube, leaving a section at the end without oil to observe the fuel injection. 2. Slowly rotate the flywheel while observing the fuel injection in the rubber tube. When the oil level in the tube rises and just stops (i.e., the fuel supply from the injection pump has just ended), immediately stop rotating the flywheel. 3. Observe whether the piston has just reached the top dead center position at this time (the cylinder head can be removed in advance to facilitate observing the piston's upward position). If the fuel injection pump stops supplying fuel too early or continues supplying fuel for too long when the piston reaches top dead center, it indicates that the fuel supply advance angle is either too large or too small. Adjustments should be made to ensure they are basically consistent, which is considered good.
14
2
Share

How to Remove Odor from Car Air Conditioning?

Here are the methods to remove odor from car air conditioning: 1. Replace the cabin air filter during maintenance: The cabin air filter needs to be cleaned and replaced regularly. After prolonged use, especially in dusty and polluted urban environments, the filter can become clogged with dust. At this point, no amount of cleaning will restore its air filtration capability, and the accumulated dust and dirt may circulate into the car cabin with the air, causing more severe pollution. 2. Open doors and sunroof to air out in sunlight: For mild interior odors, you can park the car under direct sunlight on a sunny day. Set the air conditioning system to warm air mode, turn the fan to maximum speed, and leave all doors and windows open for about ten minutes. This serves two purposes: first, ultraviolet rays can help disinfect the interior; second, the warm air facilitates complete circulation of stale air in the ventilation ducts. The advantage is that this method costs nothing, but it can only eliminate relatively weak odors. 3. Clean ventilation ducts: Bacteria in the ducts can also cause air conditioning odors. A simple solution is to use an air conditioning duct cleaner to eliminate unpleasant smells from the ventilation system.
20
1
Share

What is the yield strength of the Tourneo body steel?

The yield strength of the main body steel of the Tourneo is above 1300MPa. The main body of the Tourneo is made of boron steel. Boron steel is a low-alloy steel formed by mixing boron into low-carbon steel. The boron content ranges between 0.0005% and 0.005%, making boron steel one of the ultra-high-strength steels. Below is an introduction to the boron steel used in the Tourneo: 1. The yield strength and tensile strength of boron steel can reach above 1300MPa and 1600MPa respectively, which is about four times the strength of ordinary steel. It is classified as ultra-high-strength steel. Boron steel parts are usually formed in one step after hot processing, hence boron steel is also known as hot-formed steel. 2. In the automotive industry, boron steel can be simply equated to ultra-high-strength steel. With the emergence of more advanced steels, boron steel has gradually 'dispersed' into civilian applications. Its strength standard is about four times that of ordinary steel, but its price far exceeds four times.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.