What is the 0-100km/h acceleration time for the 2021 Teana 2.0L?

2 Answers
Taylor
07/24/25 3:27am
Teana 2.0L model achieves a 0-100km/h acceleration time of 5.9 seconds. The Teana is a mid-size sedan under Dongfeng Nissan, with body dimensions of 4901*1850*1450mm, a wheelbase of 2825mm, a fuel tank capacity of 61.3L, a trunk capacity of 586L, and a curb weight ranging from 1456kg to 1511kg. The 2021 Teana 2.0L model is equipped with a CVT continuously variable transmission and a 2.0L naturally aspirated engine, delivering a maximum torque of 197Nm and a maximum power of 115kW. It requires 95-octane gasoline and comes with 205/65R16 tires. Factors affecting a vehicle's 0-100km/h acceleration time include: Torque: Torque, in simple terms, indicates how much force is available. The greater the torque, the more force is applied to propel the vehicle, resulting in faster acceleration. For example, the Audi R8 has a maximum torque of 570Nm and accelerates from 0-100km/h in 3.1 seconds, while the BMW 6 Series GT has a maximum torque of 400Nm and achieves 0-100km/h in 6.5 seconds. Transmission efficiency: The transmission acts as a medium for power transfer, inevitably involving power loss. Higher transmission efficiency leads to better acceleration performance. Generally, the ranking of transmission efficiency is as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is referred to as the power-to-weight ratio (measured in Hp/T). A higher power-to-weight ratio results in faster acceleration. For instance, the Audi R8 has a power-to-weight ratio of 373Hp/T, while the BMW 5 Series has a ratio of 108Hp/T.
Was this review help?
1
2
Share
JamesLynn
08/10/25 11:01pm
Having driven many Japanese cars, I specifically researched the data of the 2021 Teana 2.0L. Its 0-100 km/h acceleration time is approximately 9.0 seconds. This figure is based on standard testing conditions, with the engine being a 2.0-liter naturally aspirated unit producing around 150 horsepower, paired with a CVT transmission. In actual driving, you'll notice a smooth start without the sudden burst of turbocharged cars. The smoothness is a highlight, but acceleration is relatively slow, especially when overtaking on highways. Factors affecting acceleration include the car's weight of about 1.4 tons, aerodynamic design, and the transmission's tuning style—prioritizing fuel efficiency and comfort. Compared to the Toyota Camry 2.0L's slightly over 9 seconds, the two are quite similar, but the Teana offers better cabin noise insulation. It's quite handy for daily use, just don't expect any thrilling acceleration.
Was this review help?
9
5
Share
Expand All
More Forum Discussions

How to adjust the ambient lighting in Cadillac CT5?

First, start the Cadillac CT5 and wait for the vehicle's self-check to complete. Then, locate the light control lever below the left side of the steering wheel. Turn the light control knob to the automatic headlight position, and the ambient lighting inside the car will also turn on. However, the color of the ambient lighting cannot be adjusted and is currently only available in a single color. To adjust the brightness of the ambient lighting in the Cadillac CT5, find the rotary light adjustment button on the left side. Turn the button to the left to dim the lights. Continue rotating the ambient light button inside the car to change the brightness of the ambient lighting. Turn the button to the right to brighten the lights.
6
4
Share

Should I buy a rubber blade or replace the entire wiper?

You can replace just the rubber blade of the wiper, but if the damage is extensive, a full replacement is necessary. Wiper usage tips: During daily use, exposure to summer sun and winter harsh weather can cause severe aging of the wiper, leading to issues like ineffective cleaning and unusual noises. Generally, wipers have a lifespan of 6-12 months and require regular replacement to avoid compromising the driver's visibility. Wiper replacement method: Locate the buckle position on the wiper and release it to remove the wiper; after removal, install the new wiper in the reverse order. If only replacing the rubber blade, for beam blade wipers, which consist of a rubber blade and a steel strip, simply pull out the steel strip, replace it with a new rubber blade, and reinstall it in its original position.
7
1
Share

How to Turn on the Cold Air in Qashqai?

To turn on the cold air in Qashqai, you need to press the "A/C" button and adjust the temperature to the desired level. Below is an introduction to the Qashqai's air conditioning system: 1. Dehumidification and Defogging: Set the ventilation mode to front defroster (FRONT), adjust the fan speed, and turn on the "A/C" button. Note: To quickly defrost the outer surface of the windshield, adjust the temperature and fan speed to the maximum position. 2. Air Conditioning Ventilation: Set the air conditioning to the external circulation mode, and adjust the ventilation mode, fan speed, and temperature. The A/C button activates the compressor. Turning on the A/C can dehumidify the incoming air, drying it to reduce the humidity of the air blown into the cabin, improving defogging efficiency and preventing fogging.
19
0
Share

Where is the air conditioning filter located in the Jeep Renegade?

The air conditioning filter in the Jeep Renegade is located behind the glove compartment on the passenger side. Below are the steps to replace the air conditioning filter in the Renegade: 1. Typically, the air conditioning filter is installed inside the glove compartment on the passenger side. To replace it, first open the glove compartment cover. Locate the fixing clip on the right side of the glove compartment and pull it outward with force. 2. Remove the fixing clip of the glove compartment cover to detach it. Then, squeeze both sides of the glove compartment toward the center with both hands, and the glove compartment can be taken off. 3. Once the glove compartment is removed, you will see the air conditioning filter cover. Press the fixing clips on both sides of the cover firmly, and the cover can be taken off. 4. Pull the old air conditioning filter outward, insert the new air conditioning filter, and reassemble everything in the reverse order of disassembly to restore it to its original position.
6
0
Share

Is the Prado the same as the Land Cruiser Prado?

Prado is the same as Land Cruiser Prado. Here are the relevant details about the Prado: 1. The name 'Prado' originated from the Chinese transliteration of Toyota PRADO when it was first imported into China. Now that it is exported worldwide, the name has been standardized to the English version, PRADO. 2. Toyota initially gave its cars in China names that were close to Chinese, but due to globalization, they have now adopted direct English translations. For example, Lexus was previously known as Lingzhi, Corolla as Huaguan, Prado as Badao, Camry as Jiamei, and Land Cruiser as Lude Xunyangjian. 3. Toyota Badao and Prado are the same vehicle. TOYOTA made this decision to reshape the brand image of its famous cars and better integrate into the Chinese market, as well as to eliminate the negative impact of the previous 'Badao' advertisement that offended the national sentiments of the Chinese people.
7
5
Share

Where to Reactivate a Fallen-off ETC?

According to the ETC device instructions, unauthorized removal of the ETC electronic tag (OBU), OBU device power failure, or detachment/loosening of the ETC electronic tag may cause the ETC electronic tag to become invalid. Below is the reactivation process for ETC: 1. Insert and remove the ETC card twice consecutively until the electronic tag screen displays "Bluetooth On". If "Tag Invalid" appears when inserting and removing the card twice without the electronic tag attached, this is normal and does not affect activation. Alternatively, you can directly press the button on the top of the electronic tag to enable Bluetooth. 2. Turn on Bluetooth on your phone, open the app mini-program (please download the corresponding mobile app based on the brand of the electronic tag, usually with a download QR code on the electronic tag), and enter the device activation interface. 3. Then click "Device Connection", select the device model to be connected, and wait patiently for the "Connection Successful" prompt. 4. After successful connection, follow the prompts to verify and upload a photo of the vehicle's front to complete activation. Wait for a review period of 3-5 days; after approval, you can use it normally.
16
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.