What is the 0-100 km/h acceleration time of the Lynk & Co 03+?

1 Answers
EmmanuelFitz
07/29/25 7:43am
The 0-100 km/h acceleration time of the Lynk & Co 03+ is 6.28 seconds. The Lynk & Co 03+ is equipped with a JLH3G15TD engine, featuring a 1.5T turbocharged engine paired with a 6-speed manual transmission. This engine delivers a maximum power of 115 kW and a peak torque of 245 Nm, incorporating direct fuel injection technology and utilizing an aluminum alloy cylinder head and block. The Lynk & Co 03+ has dimensions of 4639 mm in length, 1840 mm in width, and 1472 mm in height, with a wheelbase of 2730 mm. It adopts a front-engine, front-wheel-drive layout, with a MacPherson strut front suspension and a multi-link independent rear suspension.
Was this review help?
15
4
Share
More Forum Discussions

Is the BMW Mini stable at high speeds?

Mini performs very stably at high speeds with excellent handling. Here is the relevant introduction of Mini: 1. Positioning: Mini is a car brand launched by the British Motor Corporation and later acquired by BMW. It is a globally popular and highly distinctive small hatchback, introduced by the British Motor Corporation (BMC) on August 26, 1959. Over more than half a century, Mini has achieved tremendous success. 2. Power: The BMW Mini is equipped with a 1.6L naturally aspirated engine and a 1.6L turbocharged engine, both of which require gasoline with an octane rating of 95 or higher, delivering maximum horsepower of 120 and 184 respectively. The 1.6L naturally aspirated engine has a maximum output power of 90 kW and can achieve a maximum torque of 160 Nm.
15
3
Share

How to Install the Screws on a License Plate?

Below are the installation instructions for the fastening screws: 1. After receiving the license plate, there is usually a pack of fastening screws included. Open it and check if the screws are sufficient. According to relevant regulations, the vehicle license plate must be installed with 4 screws on both the front and rear, totaling 8 holes. 2. Take out the license plate screws and insert them into the anti-theft caps while rotating (be careful not to screw them in the wrong direction). 3. Position the license plate correctly, align the screws with the four gaps on the bumper, and secure them with a cross-head screwdriver. Since these screws cannot be removed once tightened, do not tighten them too much initially. Wait until all four screws are in place before tightening each one separately. 4. After tightening, cover the anti-theft caps and press them gently into place.
4
5
Share

What does it mean when a BMW electric coolant pump is missing?

It means the electronic water pump has entered power-off protection mode, usually due to a fault in the pump circuit or the pump itself. Here is relevant information about BMW's electronic water pump: 1. Concept: The electronic water pump uses piezoelectric materials as the power device, achieving complete electronic control from operation to drive. It employs an electronic integrated system to fully control liquid transmission, realizing adjustability and precision in liquid transfer - a new type of water pump. 2. Consequences of damage: A faulty electronic water pump in BMW will directly cause the engine temperature to become excessively high, may even prevent the engine from starting, and the dashboard will display a warning light.
17
3
Share

How to Deal with Resonance and Gurgling Noise Caused by Timing Belt?

Adjust the tensioner pulley, install balancing weights, and replace the engine mounts. Below are some solutions for the resonance and gurgling noise issue: 1. Symptom: A gurgling sound can be heard inside the cabin when the engine is idling. 2. Analysis: During idling, the tensioner pulley pointer swings left and right, indicating the need to adjust the belt tension. This causes the belt to vibrate and produce a gurgling sound, which may vary in intensity depending on the vehicle model and belt tension. 3. Solution: At the vibration point between the two pulleys at the top, gently press a screwdriver or wrench against the belt while idling. Additionally, install an extra pulley between the two pulleys to counteract the vibration.
13
2
Share

What Are the Hazards of Crystal Coating for New Cars?

Once a new car undergoes crystal coating, if the coating is discontinued after its validity period expires, the loss of protection will accelerate the aging process of the car paint, causing it to become dull and lose its brightness. Below is a detailed introduction to automotive crystal coating: 1. Concept: Crystal coating is a hard protective layer specifically designed for the care of key areas such as car paint, glass, tires, rims, engines, and interiors. Its main components include polysiloxane, polysilazane, and inorganic silicon. 2. Function: Crystal coating forms a robust fiber network on the car paint surface, filling in microscopic pores invisible to the naked eye, thereby achieving a mirror-like effect. It adds a thin diamond-hard shell to the paint surface, further enhancing the hardness of the paint beyond the original coating and protecting it from damage.
3
0
Share

Where can I print an ETC invoice?

To print an ETC invoice, you can log in to the Electronic Invoice Service Platform for Toll Roads or download the PiaoGen APP, and follow the on-screen instructions to issue an electronic invoice yourself. Relevant information about ETC is as follows: 1. Introduction: ETC is an Electronic Toll Collection system for automatic charging on highways or bridges. 2. Working Principle: The ETC system operates through dedicated short-range communication between the on-board ETC electronic tag installed on the vehicle and the ETC microwave antenna on the toll station lane. It uses computer networking technology to perform back-end settlement processing with the bank, achieving the purpose of vehicles passing through highway or bridge toll stations without stopping to pay the fees.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.