What is the 0-100 km/h acceleration time of the Lamando?

How to Drive a Tiptronic Car Up a Steep Slope?

Tiptronic cars should use manual mode when starting on a slope. Start in first gear, then shift to second gear while climbing for optimal fuel efficiency. The specific operation steps are as follows: 1. Depress the brake pedal. 2. Press the start button. 3. Move the automatic gear lever to the D/S position to enter manual mode. 4. Push the gear lever forward once to increase one gear. 5. Push the gear lever forward again to reach second gear. Here's an introduction to tiptronic transmissions: A tiptronic transmission is essentially a type of automatic transmission that simulates manual transmission operations through an electronic control system. Its emergence gives drivers greater operational freedom, allowing them to freely choose appropriate gears and shift timing, significantly enhancing driving pleasure.

12

3

Share

What are the correct steps for using an electronic parking brake?

Correct steps for using an electronic parking brake: 1. For automatic transmission, stop the car, shift to P gear, pull the parking brake, and turn off the engine. 2. For manual transmission, press the clutch, stop the car, shift to neutral, pull the parking brake, and turn off the engine. The electronic parking brake is a technology that achieves parking braking through electronic control, both of which rely on the friction generated between the brake disc and brake pads to achieve parking braking control. The only difference is that the control method has changed from the previous mechanical handbrake lever to an electronic button. Compared with the traditional manual mechanical parking brake system, the electronic parking brake system has the following advantages: 1. The parking brake handle is eliminated in the cabin, providing more design space for the overall interior styling. 2. The parking brake is replaced by a button, which is simple and labor-saving, reducing the driver's operational intensity.

3

1

Share

How to Deal with Scratches on a White Car?

Scratches on a white car can be categorized into three types: minor scratches, noticeable scratches that haven't damaged the paint, and scratches that have penetrated the primer. The corresponding solutions for these three scenarios are as follows: 1. Minor Scratches: If the scratches are not severe, toothpaste can be used to remove them. The fine particles in toothpaste gradually polish away the visible scratches when rubbed gently. 2. Noticeable Scratches Without Paint Damage: For deeper scratches, a touch-up pen or nail polish can be applied. It's important to choose the correct color, as uneven application may affect the appearance. 3. Scratches That Have Penetrated the Primer: For more severe scratches, colored putty can be used for repair. Since the primer lies directly above the steel panel, prompt treatment is necessary to prevent rusting caused by rainwater or other contaminants. Colored putty can effectively repair the damage. Use sandpaper on the scratched area without unnecessarily enlarging it, focusing on thoroughly cleaning off any dirt. Apply the putty carefully to ensure it fully fills the scratch. Finally, apply a compound and wax to finish the repair.

19

4

Share

What to Do When Urea is Not Consumed and Torque is Limited?

The methods to address the issue of urea not being consumed and torque being limited are as follows: 1. Check whether the post-processing wiring harness and sensors are properly connected, and make adjustments or repairs if any issues are found. 2. Inspect the urea pipeline for any leaks or abnormalities, and replace it promptly if necessary. 3. Verify the normal operation of the urea pump; if any malfunction is detected, promptly investigate the cause of the fault. 4. Examine the urea nozzle to ensure it is functioning correctly; if the nozzle is clogged or fails to open properly, clean or replace it immediately. When a vehicle does not consume urea, the problem often involves not just one fault code but a series of fault codes, requiring systematic troubleshooting. A service station diagnostic tool can be used to check the relevant codes. If the vehicle does not use urea or uses products of insufficient purity or inferior quality, the engine's torque output will be limited. Additionally, inferior-quality urea can contaminate the catalyst in the SCR catalytic reaction tank, leading to severe consequences. Therefore, it is essential to use high-quality urea products. If it is found that the vehicle is not consuming urea, timely maintenance should be performed.

16

0

Share

What Causes Excessive High Pressure in Automotive Air Conditioning Gauges?

The causes and solutions for excessive high pressure in automotive air conditioning gauges are as follows: 1. Air in the system. The system should be completely evacuated and refrigerant should be refilled. 2. System blockage. This is often caused by a blocked or malfunctioning expansion valve. The solution is to replace the expansion valve. 3. Excessive refrigerant. Symptoms include the exhaust port feeling "hot" to the touch and the suction port feeling "warm" to the touch. Normally, these areas should feel "cool" to the touch, and the compressor may occasionally produce liquid hammering sounds. The solution is to completely evacuate the system and refill the refrigerant to the correct amount. 4. Poor condenser cooling. Symptoms include the section of the pipeline from the condenser outlet to the expansion valve inlet feeling "hot" to the touch. Normally, this section should feel "warm" to the touch. The solution is to clean the condenser and radiator grille of any debris, and replace them if necessary. 5. Expansion valve failure. Symptoms include the low-pressure pipe having excessive condensation or frost. The solution is to check if the expansion valve is installed correctly. If it is, replace the expansion valve. 6. Other faults. These may include cooling fan failure, engine overheating, or excessive or insufficient lubricating oil.

13

4

Share

How many points will be deducted for driving on the highway alone with a C1 license less than one year?

Driving on the highway with a C1 license less than one year will not result in point deduction and is allowed, but the prerequisite is that the driver must be accompanied by a driver who has held a corresponding or higher-level driving license for more than three years. Otherwise, if caught driving alone on the highway, a fine will be imposed, and the driver will be ordered to exit the highway at the nearest exit. For those preparing to enter the highway, they will be educated and advised to turn back. The accompanying driver should sit in the front passenger seat to guide the probationary driver. If there is no accompanying driver or the accompanying driver does not meet the requirements, a fine of 200 yuan will be imposed. C1 Driving License: The C1 driving license is one of the codes for motor vehicle driving licenses. The scope of the C1 driving license includes small and micro passenger vehicles, light and micro cargo vehicles; light, small, and micro special operation vehicles; and small passenger vehicles with a seating capacity of less than or equal to 9 people. C1 License Test: The test subjects include four items: traffic regulations and related knowledge, field driving, road driving, and safe and civilized driving common sense.

9

4

Share

What is the 0-100 km/h acceleration time of the Lamando?

How to Drive a Tiptronic Car Up a Steep Slope?

What are the correct steps for using an electronic parking brake?

How to Deal with Scratches on a White Car?

What to Do When Urea is Not Consumed and Torque is Limited?

What Causes Excessive High Pressure in Automotive Air Conditioning Gauges?

How many points will be deducted for driving on the highway alone with a C1 license less than one year?

Which Gear is Most Suitable for Climbing Hills?

How to Replace a Beam Wiper Blade?

Does the car air conditioner consume the same amount of fuel at different settings?

What to Do When the Manual Transmission Reverse Gear Won't Engage?