What is the 0-100 km/h acceleration time of the ALPINA B3?

What are the benefits of filling car tires with nitrogen?

The benefits of filling car tires with nitrogen include: 1. Nitrogen is dry and clean, containing no water or oil; 2. As an inert gas, nitrogen does not cause oxidation to tires or corrosion to rims, thereby extending tire service life; 3. Nitrogen has low permeability in tires, maintaining stable tire pressure for extended periods, reducing the risk of blowouts and enhancing driving safety; 4. Stable tire pressure from nitrogen reduces rolling resistance, decreases fuel consumption, and minimizes tire wear; 5. Provides smoother rides on uneven roads with reduced vibration, lower noise transmission, and quieter operation. Nitrogen is chemically very stable and only reacts with hydrogen under high temperature, high pressure, and catalytic conditions to form ammonia.

6

3

Share

What are the steps for adding coolant?

Adding coolant involves the following steps: 1. Tighten the radiator drain switch and fill the radiator with coolant until it overflows. The typical coolant capacity is 4 to 5 liters. 2. Tighten the radiator filler cap. 3. Fill the engine coolant reservoir until the liquid level reaches the full mark. 4. Warm up the engine until the thermostat valve opens. 5. Turn off the engine and wait until the coolant cools down. 6. Remove the radiator filler cap and check the coolant level. Coolant, also known as antifreeze coolant, prevents the engine from freezing in winter and cools the engine when it generates high temperatures during operation, ensuring the vehicle functions properly in various environments.

15

0

Share

What are the road traffic regulations for motorcycles?

Motorcycle road traffic regulations vary in terms of different roads, speed, and safety as follows: 1. Different roads: On roads divided into motor vehicle lanes and non-motor vehicle lanes, motorcycles must drive in the motor vehicle lane, while mopeds should keep to the right within the motor vehicle lane. On roads without a centerline or division between motor vehicle and non-motor vehicle lanes, two-wheeled motorcycles and mopeds should drive on the right side of the road center. On roads without traffic signals, they should proceed under the principle of ensuring safety and smooth traffic. 2. Speed: Motor vehicles on the road must not exceed the maximum speed indicated by speed limit signs. On road sections without speed limit signs, a safe speed should be maintained. Speed should be reduced when driving at night, on dangerous road sections, or encountering sandy roads, hail, rain, snow, fog, ice, etc. 3. Safety: When driving in the same lane, the following vehicle should maintain a safe distance from the vehicle in front to allow for emergency braking. Pay attention to the situation of the vehicle ahead and avoid overtaking easily. When driving, both the driver and passengers must use seat belts as required and wear safety helmets as stipulated. For motorcycle cargo, the height from the ground must not exceed 1.5m, and the length must not exceed 0.2m beyond the vehicle body. For two-wheeled motorcycles, the cargo width must not exceed 0.15m on either side beyond the handlebars, and for three-wheeled motorcycles, the cargo width must not exceed the vehicle body. The rear seat of a motorcycle must not carry children under 12 years old, and mopeds must not carry passengers. When driving a motorcycle, hands must not leave the handlebars, and items must not be hung on the handlebars. Two-wheeled motorcycles must not carry passengers when driving on highways.

19

1

Share

What brand is the engine of the Volkswagen Lavida?

The engine of the Volkswagen Lavida is domestically produced, manufactured in China through a joint venture with German technology, and designed and developed by Shanghai Volkswagen itself. The engine model used in the Volkswagen Lavida is the EA211-DSB, with a maximum horsepower of 150 HP, a maximum power output of 110 KW, a maximum power speed range of 1750-3000 rpm, and a peak torque of 250 N.m. The vehicle's power performance is relatively smooth and has long been known for its low fuel consumption and low maintenance costs. For the daily maintenance of the Volkswagen Lavida's engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices in the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and oil filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, which can cause various problems for the engine. To avoid malfunctions, the oil should be changed periodically according to usage conditions, and the oil level should be kept moderate. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and the oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing the oil to bypass through the relief valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. In small amounts, it remains suspended in the oil; in large amounts, it precipitates, clogging the filter and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

6

3

Share

What are the new regulations for National IV motorcycles in 2021?

The new policies for National IV motorcycles in 2021 mainly include four aspects of regulations: relaxing the age restrictions for applying for a driver's license; adjusting the annual inspection time for motorcycles between 6-10 years; modifying the inspection procedures for vehicles with 7-9 seats; and making new plans for vehicles not covered by the new policies (vehicles involved in major traffic accidents and modified vehicles will still follow the regulation of annual inspections). Additional details are as follows: 1. Nationwide inspection for motorcycles: Motorcycles registered within 6 years are exempt from on-site inspections, and motorcycle inspections can be conducted nationwide. Motorcycles exempt from inspection within 6 years are also exempt from environmental inspections. For applicants who need inspections in provinces (or autonomous regions/municipalities) other than where the motorcycle is registered, the requirement for an inter-provincial inspection authorization letter is abolished. For those who have already obtained such a letter but have not yet undergone inspection, the new regulations will apply, and no further authorization letter will be required. For motorcycles exempt from inspection within 6 years, the inspection exemption mark can be applied for across different provinces (or autonomous regions/municipalities). 2. Clarification of inspection exemption periods: Vehicles registered after June 1, 2017, can enjoy the policy of three inspection exemptions. Vehicles registered between June 1, 2015, and May 31, 2017, having undergone one inspection, can enjoy two inspection exemptions. Vehicles registered between June 1, 2014, and May 31, 2015, having undergone two inspections, can enjoy one inspection exemption. Vehicles registered before May 31, 2014, will still follow the original regulations, requiring annual inspections. Note: Inspection exemption does not mean no inspection. When the annual inspection is due, motorcycle owners still need to go to the vehicle management office or its service agents to apply for the annual inspection compliance mark.

9

1

Share

What is the process for obtaining a license plate in Shanghai?

Shanghai's license plate acquisition process is as follows: 1. Document preparation: Owner's ID card and copy, original and duplicate of compulsory traffic insurance, the 4th and 1st copies of the car purchase invoice, vehicle certificate and copy; 2. Vehicle inspection; 3. Review and number selection; 4. Collecting the license plate and relevant certification documents. The vehicle license plate is a hard-plate number tag with a unified format and style as stipulated by national vehicle management regulations. It is issued by the vehicle management authority after reviewing, inspecting, and registering the vehicle applying for the plate. The vehicle registration certificate is issued by the vehicle management authority, recording the main content of the vehicle's initial registration. It is kept by the owner, carried with the vehicle, and serves as a unified format registration book for recording changes and inspections at any time.

12

4

Share

What is the 0-100 km/h acceleration time of the ALPINA B3?

What are the benefits of filling car tires with nitrogen?

What are the steps for adding coolant?

What are the road traffic regulations for motorcycles?

What brand is the engine of the Volkswagen Lavida?

What are the new regulations for National IV motorcycles in 2021?

What is the process for obtaining a license plate in Shanghai?

How to Distinguish Between National 5 and National 6 Vehicles?

What to Do When the Car Navigation System Won't Turn On?

Can a Ford Mondeo with a noisy water pump still be driven?

Where is the cabin air filter located on the Peugeot 408?