What is the 0-100 km/h acceleration time for the Mazda Atenza 2.0L?

How to Attach Temporary License Plates to a Vehicle?

Temporary license plates should be attached to the vehicle as follows: one plate should be affixed to the lower left or right corner of the front windshield inside the vehicle, in a position that does not obstruct the driver's view. The other plate should be affixed to the lower left corner of the rear windshield inside the vehicle. For passenger vehicles that have not yet been registered (excluding cargo vehicles, including sedans, etc.) and need to be driven temporarily on the road, both temporary license plates must be displayed simultaneously. The temporary license plate, also known as a temporary vehicle movement permit, is a paper license issued by the vehicle management department of the public security bureau for newly purchased vehicles before formal registration. Typically, the validity period of a temporary license plate does not exceed thirty days.

13

5

Share

How long should the engine run if the car hasn't been driven for a long time?

If the car hasn't been driven for a long time, the engine should run for about 10 minutes. It's recommended to start the car once a week and let it idle for 10 minutes to keep all parts moving and prevent rust, which is beneficial for the vehicle. Even when parked and unused, the car battery will self-discharge. Prolonged inactivity may lead to sulfide formation on the battery surface, affecting charging efficiency, and in extreme cases, could cause complete battery failure. Drivers can occasionally take the car for a short drive to extend battery life, which not only facilitates faster charging but also reduces wear on chassis components.

13

1

Share

What does DSP in a car mean?

DSP in a car stands for Digital Signal Processor, which is a digital audio signal processing device. It first converts multi-channel input analog signals into digital signals, then applies a series of tunable algorithm processing to the digital signals to meet application requirements such as improving sound quality, matrix mixing, noise cancellation, echo cancellation, and feedback elimination. Finally, it outputs multi-channel analog signals through digital-to-analog conversion. Due to the limited space in cars with multiple speakers in non-ideal positions, irregular cabin shapes, strong glass reflections, and significant acoustic defects - combined with speaker frequency response limitations, enclosure materials and spatial constraints - the sound reaching human ears can have serious deviations. Therefore, digital audio signal processing becomes necessary to correct these defects through digital technology.

5

2

Share

What is a Hands-Free Trunk?

Hands-free trunk allows you to open the trunk without using your hands. Simply sweep your foot under the rear bumper where the sensor is located, and the trunk will open automatically. To close the trunk, the operation method is the same as opening it. The sensor for the hands-free trunk is a device that receives signals or stimuli and responds, capable of converting the measured physical or chemical quantity into another corresponding output. It is used in automation control, security equipment, etc. When using a hands-free trunk, the following precautions should be noted: 1. Ensure the remote key is carried with you, the battery is sufficiently charged, and perform a light kicking motion under the sensor on the left side of the rear bumper; 2. If this function is used too frequently, it may enter a protection mode and will require some time to recover.

12

4

Share

What are the reasons for loud noise when stepping on the car accelerator?

Car accelerator noise is loud because: the engine loses power, and the internal valves of the engine are blocked. The accelerator, also known as the throttle or air valve, refers to the control device that regulates the engine's power (thrust). In piston-type aircraft engines, the accelerator controls the throttle opening of the carburetor to regulate the cylinder's filling amount, thereby determining the engine's output power. In gas turbine engines, the accelerator controls the metered fuel flow of the fuel regulator, thus determining the thrust generated by the engine. The accelerator position is controlled by the pilot in the cockpit through the throttle lever, which is transmitted to the carburetor or fuel regulator on the engine via control system components such as pushrods, rocker arms, torque tubes, cables, pulleys, and sector gears.

11

3

Share

Which is More Fuel-Efficient Between 95 and 92?

95 gasoline is slightly more fuel-efficient than 92 gasoline. Here are the relevant details: 1. Stronger Power Output: 95 gasoline provides stronger power output when burned, allowing the car to travel a longer distance. Additionally, 92 gasoline has relatively poorer anti-knock performance compared to 95 gasoline, making it more prone to knocking, which ultimately leads to higher fuel consumption. 2. Differences: In essence, there isn't a significant difference between 92 and 95 gasoline. The only difference lies in the octane rating. 95 gasoline consists of 95% isooctane and 5% n-heptane, while 92 gasoline is composed of 92% isooctane and 8% n-heptane. A higher octane rating means better anti-knock performance, and of course, a higher price. Moreover, 95 gasoline burns more easily than 92 gasoline in terms of stability, resulting in greater power output.

10

2

Share

What is the 0-100 km/h acceleration time for the Mazda Atenza 2.0L?

How to Attach Temporary License Plates to a Vehicle?

How long should the engine run if the car hasn't been driven for a long time?

What does DSP in a car mean?

What is a Hands-Free Trunk?

What are the reasons for loud noise when stepping on the car accelerator?

Which is More Fuel-Efficient Between 95 and 92?

What to Do When There's a Squeaking Sound While Braking?

How Many Cylinders Does the New Excelle Engine Have?

What grade of gasoline should a Focus use?

What does the prompt 'Please repair power steering, drive with caution' mean?