What is the 0-100 km/h acceleration time for the CR-V?

1 Answers
Emily
07/30/25 9:54am
CR-V's 0-100 km/h acceleration time ranges from 9.0 to 10.3 seconds. The introduction and influencing factors of 0-100 km/h acceleration are as follows. Introduction to 0-100 km/h acceleration: 0-100 km/h acceleration refers to the time taken to accelerate from 0 to 100 kilometers per hour. Generally, a 1.6-liter compact car achieves a 0-100 km/h acceleration time between 11 to 13 seconds, while supercars mostly complete it in less than 3.8 seconds. Among vehicles with the same displacement, models equipped with turbocharged engines have a significant advantage in 0-100 km/h acceleration due to their more powerful output and a very wide range of maximum torque, allowing the vehicle to maximize acceleration at very low RPMs. Factors influencing 0-100 km/h acceleration: In terms of the testing environment alone, factors include temperature, humidity, wind direction, wind speed, altitude, and road surface grip. Vehicle-related aspects such as condition, fuel quality, and load also play a role. Additionally, the tester's weight, reaction time, and testing method can have some influence.
Was this review help?
15
0
Share
More Forum Discussions

What does 11 cumulative demerit points on a driver's license mean?

11 cumulative demerit points on a driver's license means that the license has accumulated 11 points (due to traffic violations) within one scoring cycle. Impact of having 11 demerit points on a driver's license: You can still drive with 11 demerit points on your license, and it doesn't significantly affect your driving. However, you should drive more carefully to avoid accumulating 12 or more points. The main impact of having 11 demerit points may be the need to pay corresponding fines. After handling the violations, the points will automatically reset to zero at the start of the next scoring cycle. Regulations on driver's license demerit points: For the first year after obtaining a driver's license (the probationary period), if you accumulate 12 or more points, your probationary driving qualification will be revoked. The driver must pass all subject exams again to regain the license. After the probationary period ends, no license replacement is required, and it automatically becomes a full license. Outside the probationary period, if you receive 12 points in a single violation or accumulate 12 points in one scoring cycle, the traffic management department of the public security organ will confiscate your driver's license. The driver must attend a seven-day course on road traffic safety laws, regulations, and related knowledge at the traffic management department of the public security organ where the license was issued or where the violation occurred within 15 days.
2
0
Share

How to reset the tire pressure for the 2020 Outlander?

2020 Outlander tire pressure reset method: First, turn on the ignition, then press and hold the tire pressure monitoring reset button until you hear a "ding" sound before releasing. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the dashboard warning light will turn off, indicating the tire pressure reset is complete. Precautions for inflating tires: Always use a pressure gauge to check the pressure to avoid over-inflation, which could cause the tire to burst. After stopping the vehicle, wait for the tires to cool down before inflating, as tire temperature rises during driving, affecting the pressure. Check the valve stem. If the valve stem and valve core do not fit smoothly, have protrusions, depressions, or other defects, it may be difficult to inflate or measure pressure. Pay attention to cleanliness when inflating. The air being pumped in should not contain moisture or oil to prevent deterioration and damage to the inner tube rubber. Do not exceed the standard pressure too much during inflation and then release air, nor should you over-inflate due to prolonged inability to inflate while traveling. Exceeding the standard pressure too much can cause excessive stretching of the cords, reducing their strength and affecting the tire's lifespan.
5
5
Share

How to Check the Ignition Coil?

Methods to check the ignition coil: 1. Set the vehicle's ignition switch to the "ON" position, then unplug the ignition coil connector. Use a multimeter to measure pin 3 on one end and the ground wire on the other; 2. Unplug the ignition coil connector, use a multimeter to measure pin 1 on one end and pin 5 of the ECU on the other, checking for any short circuits or open circuits; 3. Use a multimeter to measure whether the resistance of the sensor's primary coil is 0.9. The core components of the ignition system are the ignition coil and the switching device. Increasing the energy of the ignition coil enables the spark plug to generate sparks with sufficient energy, which is a fundamental requirement for the ignition system to adapt to the operation of modern engines.
20
0
Share

How long does the first maintenance usually take to complete?

The first maintenance usually takes 1 to 2 hours to complete. Items that need to be replaced during the first maintenance include: engine oil, oil filter, air conditioning filter, and air filter. Other items included in the first maintenance are: 1. Checking the levels of coolant, battery fluid, and windshield washer fluid; 2. Inspecting the fluid levels of the brake and clutch systems, as well as the power steering fluid reservoir; 3. Examining tire pressure and wear, and tightening screws to the specified torque. Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the vehicle, also known as car servicing. Modern car maintenance primarily includes the care of the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, and more.
1
2
Share

What is the maximum power of the Qin New Energy's electric motor?

The maximum power of the Qin New Energy's electric motor is 110 kW. It features a front-wheel drive system, with a MacPherson strut independent suspension at the front and a torsion beam non-independent suspension at the rear. The BYD Qin is a high-performance sedan under the BYD brand. The dimensions of this car are 4740 mm in length, 1770 mm in width, and 1480 mm in height, with a wheelbase of 2670 mm and a curb weight of 1630 kg. In terms of configuration, the BYD Qin is equipped with features such as electric front seat adjustment, ACC adaptive cruise control, keyless entry, one-button start, electronic parking brake, and an electric sunroof.
17
1
Share

How often should the differential gear oil be changed for the Nissan Qashqai?

Nissan Qashqai differential gear oil should be changed every 60,000 kilometers. Gear oil is generally used in gear transmission mechanisms such as vehicle steering gears, transmissions, and drive axles. The differential mainly consists of left and right half-shaft gears, two planetary gears, and a gear carrier, enabling the left and right drive wheels to rotate at different speeds. The Qashqai is a compact SUV with dimensions of 4401mm in length, 1837mm in width, and 1593mm in height, a wheelbase of 2646mm, and a fuel tank capacity of 65 liters. In terms of exterior design, the front face of the Nissan Qashqai still adopts Nissan's family-style design, with a V-shaped chrome trim running through the blackened grille, making it very eye-catching.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.