What is senova?

What does it mean when a Geely Emgrand displays a sensor malfunction?

For a Geely Emgrand sensor malfunction, replacement or repair according to the relevant service manual is required. Automotive sensors are input devices for the vehicle's computer system. They convert various operational conditions of the car, such as speed, temperature of various mediums, and engine operating conditions, into electrical signals for the computer, enabling the engine to operate in its optimal state. The testing methods for automotive sensors are as follows: 1. Unplug the connector, turn the key to the second position, and use a voltmeter to measure and confirm that the power line has voltage output. 2. Use the meter to identify the ground wire. With the voltage setting, connect one probe to the confirmed power line and the other probe to the remaining two wires. The wire that shows voltage is the ground wire, and the remaining one is the signal wire. 3. Now, turn off the key, disconnect the signal wire, plug back the connector, start the engine, and measure the voltage between the signal wire and the ground wire. There should be a signal voltage output, which should be less than the supply voltage. If there is no voltage, the sensor is likely faulty. 4. While performing the above steps, also check the condition of the signal teeth on the camshaft, ensure there are no obstructions between the camshaft sensor and the signal teeth, and verify that the gap is normal.

9

3

Share

Can a newly purchased car be driven on the road immediately?

A newly purchased car cannot be driven on the road without a license plate. If driven, it will be impounded by traffic police and a fine of 200 yuan will be imposed. Any vehicle driven on the road without a license plate will be stopped by traffic police. Even when driving a new car home, you must first obtain a temporary license plate. It is best to apply for a temporary license plate before driving a new car on the road. According to traffic laws, unregistered motor vehicles without official license plates that need to be driven temporarily must obtain temporary permits. According to Article 95 of the Road Traffic Safety Law, motor vehicles driven on the road without license plates, inspection qualification marks, insurance marks, or without carrying the vehicle registration certificate or driver's license will be impounded by traffic management authorities. The authorities will notify the parties to provide the corresponding permits, marks, or complete the necessary procedures, and may impose penalties in accordance with Article 90 of this law. If the parties provide the corresponding permits, marks, or complete the necessary procedures, the vehicle should be promptly returned. Intentionally covering, damaging, or improperly installing license plates will result in penalties according to Article 90 of this law.

17

3

Share

Can Private Cars Carry Passengers for Hire?

No. Private cars carrying passengers for hire will be ordered to cease operations by the road transport management agencies at or above the county level; if there are illegal gains, such gains will be confiscated and a fine ranging from 2 to 10 times the illegal gains will be imposed. The following is an introduction to illegal operations: Road Passenger Transport Operations: Refers to the activity of transporting passengers or goods on roads using transportation vehicles. Road transport activities can be divided into commercial road transport and non-commercial road transport based on whether they are profit-oriented. Commercial Road Transport: Commercial road transport, also known as road transport operations, mainly refers to road transport that provides services to the public, involves fee settlements, or obtains remuneration. During commercial road transport, various settlement methods are used, including not only separate settlement of freight charges but also combined settlement of freight charges and loading/unloading fees with the price of goods, freight charges and loading/unloading fees with project costs, and freight charges with service fees or contract fees, among others.

11

4

Share

What is the Speed Ratio of Pulleys?

The calculation formula for pulley speed: Assuming the diameter and speed of the motor pulley (driving pulley) are d1 and n1, and the diameter and speed of the driven pulley are d2 and n2, the mechanical transmission principle yields the pulley speed calculation formula: d2/d1 = n1/n2 = i; that is, d2 = d1 × (n1/n2). Below are related introductions: Definition: Pulleys belong to the category of hub-like components, generally relatively large in size, and are primarily manufactured through casting or forging in terms of production processes. Larger-sized designs typically employ casting methods, with materials usually being cast iron (which has good casting properties), and rarely cast steel (as steel has poor casting properties). Representation: It is denoted by the symbol "n"; its international standard unit is r/s (revolutions per second) or r/min (revolutions per minute), and it is also represented as RPM (revolutions per minute, mainly used in Japan and Europe). When the unit is r/s, the value is equal to the frequency, i.e., n = f = 1/T, where T is the period of circular motion.

19

3

Share

What Causes the Squeaking Sound When Pressing and Releasing the Clutch Pedal?

It is caused by poor lubrication, wear, looseness, or damage of the clutch release bearing. Lubricating oil needs to be added to the clutch release bearing or it should be replaced promptly. Abnormal Clutch Issues in Vehicles: Pay Attention to Clutch Slippage: If the free travel of the clutch pedal is too small, the release bearing frequently presses against the diaphragm spring, keeping the pressure plate in a semi-engaged state. Alternatively, the clutch pressure plate spring may be too soft or broken, or the screws connecting the clutch to the flywheel may be loose. Incomplete Disengagement: With the engine idling, the clutch only disengages when the clutch pedal is pressed almost to the floor. If pressing the clutch pedal makes it difficult to shift gears or causes a harsh grinding noise from the transmission, or if the vehicle starts moving without lifting the clutch pedal after shifting, these indicate incomplete clutch disengagement. Measuring the Pedal Travel: The clutch should firmly engage when the pedal is pressed to 3/4 of its travel. Otherwise, check if the travel is appropriate. Use a ruler to measure the pedal height at its highest position, then measure the height when resistance is felt upon pressing the pedal. The difference between these two values is the clutch pedal travel.

2

5

Share

Volkswagen CC 30,000 km Maintenance Items

For the Volkswagen CC's 30,000 km maintenance, replacing the engine oil and oil filter is a mandatory task. Under the high-temperature and high-pressure conditions inside the engine, the shelf life of engine oil is significantly shortened, and its performance greatly deteriorates. Over time, it fails to protect the engine effectively. The oil filter prevents impurities from mixing into the oil, which can cause oxidation, leading to the formation of sludge and clogging the oil passages. Both the engine oil and oil filter should be replaced simultaneously. The air filter should be replaced every 10,000–15,000 km, and the fuel filter every 30,000 km. 1. Engine oil and four filters. The four filters include: oil filter, air filter, fuel filter, and cabin air filter. The oil filter needs to be replaced at every maintenance service, while the air filter is recommended for replacement every 10,000–15,000 km, and the fuel filter every 30,000 km. The cabin air filter is suggested to be replaced every six months. If cost-saving is a priority, the cabin air filter can be skipped. However, the fuel filter must be replaced during the 30,000 km major maintenance. 2. Throttle body cleaning. Throttle body cleaning is unnecessary before 30,000 km. If a 4S shop or repair shop staff recommends this service at 10,000 or 20,000 km, you can directly decline. By 30,000 km, the car has typically been driven for at least a year or more. Over time, the throttle body accumulates carbon deposits at the intake due to prolonged use, leading to reduced airflow. This can cause minor idle instability, idle vibration, sluggish acceleration, and indirectly increase fuel consumption. At this point, it's advisable to inspect the throttle body, spark plugs, and other components that might contribute to these issues. 3. Spark plugs. By 30,000 km, the spark plugs are due for replacement. Although they haven't completely lost their ignition capability, their performance has significantly degraded. Poor ignition directly affects idle vibration, engine misfires, and weak acceleration. Reduced ignition performance also increases engine load, which is one of the factors contributing to higher fuel consumption. 4. Air conditioning system cleaning. Air conditioning cleaning removes dust and dirt from the AC ducts and provides a sterilizing effect. This service is optional. However, if the car has never undergone AC cleaning before 30,000 km, now is a good time to do it.

16

1

Share

What is senova?

What does it mean when a Geely Emgrand displays a sensor malfunction?

Can a newly purchased car be driven on the road immediately?

Can Private Cars Carry Passengers for Hire?

What is the Speed Ratio of Pulleys?

What Causes the Squeaking Sound When Pressing and Releasing the Clutch Pedal?

Volkswagen CC 30,000 km Maintenance Items

Can a Private Car Be Converted Back After Being Changed to a Commercial Vehicle?

Can a car wash remove glue from a car?

Is there a mandatory scrapping period for passenger cars?

What does the 'H' on small car tires mean?