What is Jack Ma's new energy car called?

What is the original gear position for Mercedes-Benz gear shift?

Mercedes-Benz gear shift operation method: The original position is the N gear (neutral). The following are the precautions for driving a Mercedes-Benz: 1. Normal roads: There are no special requirements for the car's gear position. You can drive normally by keeping it in D gear. 2. Parking: When the engine stops running, you need to shift to P gear, indicating that the car is no longer in use. Some cars require shifting to P gear to remove the key. 3. Reversing: After stepping on the brake and stopping the car from moving forward, you can shift to R gear. Gently releasing the brake will allow the car to reverse. 4. Waiting while parked: Or when driving on congested roads, you can shift to N gear. 5. Highways: Or when overtaking at high speed, you can shift to S gear. S gear is the car's sport mode, allowing free gear changes like D gear. You can also choose S gear when climbing hills, as this gear provides maximum torque output and acceleration.

15

4

Share

Can I shift directly from D to P when parking?

It is not recommended to shift directly from D to P when parking. The correct method for parking an automatic transmission vehicle is as follows: 1. Press the brake pedal to come to a complete stop; 2. Shift the gear from D to N; 3. Engage the parking brake and turn off the engine; 4. Release the foot brake (but keep the power on) to ensure the vehicle is completely stationary under the parking brake's effect; 5. Press the foot brake again and shift the gear from N to P; 6. Release the foot brake; 7. Turn the key back to the off position and remove it. The procedure for starting an automatic transmission vehicle is: 1. Without pressing the foot brake, press the start button twice to initiate the vehicle's computer system self-check (for at least six seconds); 2. Press the foot brake and push the start/stop button to ignite the engine; 3. Release the foot brake and allow the engine to warm up while stationary; 4. Press the foot brake, release the parking brake, and shift the gear from P to D; 5. Gradually release the foot brake to start moving; 6. Depending on road conditions, smoothly press the accelerator pedal to increase speed.

10

1

Share

Which turn signal should be turned on when exiting the highway?

When a motor vehicle exits the highway, the right turn signal should be activated to enter the deceleration lane, and then the vehicle should slow down before exiting. When exiting the highway, pay attention to the intersection warning signs, divert the vehicle from the main lane into the deceleration lane to reduce speed, and then enter the general road via the ramp. Additional information about automotive lights is as follows: 1. Headlights: The main purpose of headlights is to illuminate the road and objects ahead to ensure driving safety. They can also be used as a signal for overtaking at night by alternating between high and low beams. Headlights are installed on both sides of the front of the car, with 2 or 4 units per vehicle. The bulb power is 45~60W for high beams and 25~55W for low beams. 2. Fog lights: Fog lights are installed near the headlights or slightly lower. They are used in low visibility conditions such as fog, snow, heavy rain, or dust to illuminate the road and provide signals to oncoming vehicles. The light is mostly yellow because yellow light has a longer wavelength and good fog-penetrating performance. The bulb power is generally 35W.

2

0

Share

Can the Tiida's wipers be manually lifted?

Tiida's wipers can be manually lifted. Below are some precautions for using wipers: 1. Maintain cleanliness: When there are streak marks on the glass surface, the wiper blades may be dirty. You can sprinkle alcohol on a towel and wipe the surface of the wiper blades. Cleaning them once a month can improve the working efficiency of the wipers. 2. Check the rubber: If the wipers make unusual noises while operating, the rubber blades may be aged or cracked. If the wear is not severe, you can use sandpaper to smooth out rough spots on the surface. 3. Avoid sunlight: Park the car in a shaded area where it is not exposed to sunlight, such as a garage. Summer is particularly harsh on cars. Wiper blades are made of rubber, and exposure to sunlight will only accelerate their aging. 4. Refill fluid: Adding plain water directly to the windshield washer fluid reservoir is not conducive to the maintenance of the windshield and wiper blades in the long run. To ensure the longevity of the components, always use proper windshield washer fluid. Refill the washer fluid in time to be prepared for unexpected needs.

13

2

Share

How fast do you drive on the highway?

There is no unified regulation, as speed limits vary on different highways. Even on the same highway, speed limits may differ in different sections. Starting from the left lane, the general speed limits are as follows: First lane: 100-120 km/h (usually dedicated to passenger cars); Second lane: 80-100 km/h; Third lane: 60-100 km/h. Here are other regulations: 1. Drive according to the rules: The national speed limit does not exceed 120 km/h, but highways may set special speed limits based on specific conditions, such as posting speed limit signs of 110, 100, or 90 km/h. In such cases, drivers must adhere to the posted speed limits. 2. Drive according to the lane speed requirements: On highways, the maximum speed for small passenger vehicles must not exceed 120 km/h, for other motor vehicles 100 km/h, and for motorcycles 80 km/h. If there are two lanes in the same direction, the minimum speed for the left lane is 100 km/h; if there are three or more lanes, the minimum speed for the leftmost lane is 110 km/h, and for the middle lane 90 km/h. If the speed limit indicated by road signs differs from the above lane speed regulations, drivers must follow the speed limit indicated by the road signs.

16

5

Share

What are the steps for removing iron particles from car body?

The steps for removing iron particles from car body are: 1. Use a cloth dipped in bathroom cleaner and wipe back and forth on the rusty areas; 2. Choose transparent, non-sticky engine oil, dip it on a cloth, and wipe the rusty parts; 3. You can add some acidic substances, such as dilute hydrochloric acid or oxalic acid, but be careful not to use excessive amounts to avoid secondary corrosion; 4. Use a car paint iron particle remover, which can quickly dissolve iron particles and oxidation layers on the paint surface. Iron particles on the car paint surface will adhere to the car surface as water evaporates, and after oxidation, they will turn into yellowish-brown rust spots. The iron particles will continuously spread and oxidize the surrounding paint, eventually penetrating the surface layer of the paint and reaching the primer, directly oxidizing the metal or, due to high speed or high temperature from the engine, softening the paint and allowing the particles to embed. Once iron particles fuse into the car paint, the damage progresses from the surface inward, gradually causing the paint to lose its luster, discolor, and form 'psoriasis-like' spots, making maintenance very difficult. In severe cases, the paint may peel or flake off, becoming irreparable.

15

1

Share

What is Jack Ma's new energy car called?

What is the original gear position for Mercedes-Benz gear shift?

Can I shift directly from D to P when parking?

Which turn signal should be turned on when exiting the highway?

Can the Tiida's wipers be manually lifted?

How fast do you drive on the highway?

What are the steps for removing iron particles from car body?

What is the difference between the Reiz S and V?

Under what circumstances can one not obtain a driver's license?

Why Does the Brake Make Noise at Low Speed?

How to Determine if a Six-Wire Electronic Throttle is Faulty?