What is considered a normal fuel consumption per 100 kilometers?

1 Answers
ClaireDella
07/29/25 9:29pm
There is no precise answer to what constitutes normal fuel consumption per 100 kilometers, as various factors such as vehicle model, engine displacement, road conditions, speed, driving habits, vehicle age, condition, quality, and load can all influence the final fuel consumption. Taking a 1.6L displacement family car as an example, if driven normally in urban areas without poor driving habits, a combined fuel consumption of around 7.5 liters per 100 kilometers is considered fuel-efficient. Therefore, a consumption of approximately 0.5~0.7 liters per kilometer is relatively low. If a 1.6L displacement vehicle exceeds 7.5L, its fuel consumption is relatively high. The level of a car's fuel consumption is directly related to five major factors: driving habits, the vehicle itself, road conditions, natural wind, and ambient temperature. Reasons that may increase fuel consumption include: Driving habits: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before reaching a red light can increase fuel consumption. The vehicle itself: Cars with larger displacements generally consume more fuel than those with smaller displacements because larger displacements typically require more power and thus more gasoline combustion. Heavier vehicles also consume more fuel due to the greater driving torque needed. Road conditions: Driving on unpaved roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the vehicle's resistance and fuel consumption. Low ambient temperatures: When the engine block is cold, the injected gasoline does not atomize easily, requiring more gasoline for combustion, which increases fuel consumption. Additionally, in cold weather, the engine's computer may control higher idle speeds to warm up the engine, further increasing fuel consumption.
Was this review help?
19
2
Share
More Forum Discussions

Can You Drive with a Brake Light Malfunction?

If the electronic parking brake system malfunctions, the vehicle should not continue to be driven. Below is a detailed introduction to the electronic parking brake system: 1. Compared to Lever Handbrakes: The electronic parking brake system replaces traditional mechanical levers and tire cables, substituting the conventional lever handbrake with an electronic handbrake button. It is safer than traditional lever handbrakes, as the braking effect is not influenced by the driver's force, turning the traditional lever handbrake into an easily accessible button. 2. Main Applications: The electronic parking brake system is primarily used in tractors and cargo trucks. The electronic parking brake energy-saving system is equivalent to the engine having a three-gear selection button, allowing free selection based on different road conditions and load capacities. This keeps the engine operating within the optimal fuel economy range, achieving fuel-saving effects.
18
1
Share

What is the correct way to use hazard warning lights?

The correct usage of hazard warning lights is as follows: 1. When driving in foggy conditions, due to reduced visibility, you should not only turn on the hazard warning lights but also activate the fog lights to alert other vehicles. 2. In case of vehicle breakdown or traffic accidents on the road, hazard warning lights should be turned on to warn passing vehicles for safety. On highways, failure to use lights and set up warning signs properly after a breakdown or accident will result in a 12-point penalty. 3. When towing a malfunctioning vehicle, both the towing vehicle and the towed vehicle should turn on the hazard warning lights to indicate their abnormal status. 4. When temporarily parked on the road, turn on the hazard warning lights to alert other vehicles. 5. When forming a convoy as permitted by traffic authorities, all vehicles in the convoy should activate their hazard warning lights.
18
4
Share

What are the common transmission faults of Honda CR-V?

Common transmission faults of Honda CR-V include: 1. Accumulation of dirt and impurities inside the valve body, forming blockages that prevent effective regulation of oil pressure; 2. Transmission overheating, which can degrade the quality and friction characteristics of automatic transmission fluid, leading to sludge buildup inside the transmission, causing jerking and impact. If the temperature exceeds 120 degrees, rubber sealing materials may begin to harden or hydraulic pressure may decrease. Below is more information about the 2021 Honda CR-V 240TURBO manual two-wheel-drive classic edition: 1. It is a compact 5-door, 5-seat SUV with dimensions of 4621mm in length, 1855mm in width, and 1679mm in height. 2. It has a wheelbase of 2661mm, equipped with a 6-speed manual transmission, and the engine delivers a maximum torque of 243 Nm and a maximum horsepower of 193 hp.
14
3
Share

Do You Need to Replace the Control Arm When the Control Arm Bushing is Worn Out?

Do You Need to Replace the Control Arm When the Control Arm Bushing is Worn Out. Lift the vehicle: Remove the control arm bushing, then remove both ends of the control arm. Select two corresponding size metal sleeves and install the purchased bushing. The larger ones are left and right specific, marked with (L or R). Remove the old control arm: Then proceed with disassembly to remove the screws. This is the removed bushing, which falls off with a gentle pull, indicating quality issues. It may cause drumming sounds, front and rear tire play, accelerate the wear of the small tie rod, and thus affect the stabilizer bar and shock absorber. Install the new control arm: Apply dish soap to the new control arm bushing for lubrication to facilitate installation. Other lubricants that do not corrode rubber can also be used, but engine oil should not be used.
3
5
Share

Is it necessary to install a grounding strip to remove static electricity from private cars?

It is necessary to install a grounding strip to remove static electricity from private cars. Static electricity buildup in winter can lead to hazards: Especially in winter or abnormally dry environments, static electricity cannot dissipate through the air. Installation ensures improved vehicle safety. For older vehicles with minor oil seepage, static electricity may generate sparks that pose certain life safety threats. While driving, unexpected static shocks may cause excessive fright, potentially leading to traffic accidents. Static electricity can harm human health: Accumulated static electricity in the human body can damage health, severely affecting metabolism, raising blood sugar levels, causing skin diseases, and leading to autonomic nervous system disorders, reduced immunity, and increased susceptibility to illnesses like colds. Particularly during refueling at gas stations, it may also trigger accidental incidents.
11
2
Share

Can I Switch from 95 Octane Gasoline to 92 Octane Gasoline for My Car?

Car 95 octane gasoline can be switched to 92 octane gasoline. Different compression ratios apply: Generally, cars with a compression ratio between 8.5 and 9.5 should use 92 octane gasoline; cars with a compression ratio greater than 9.5 should use 95 octane gasoline. The choice is relatively based on the fuel tank settings of the car itself. Different octane levels: The octane level of 92 octane gasoline is lower than that of 95 octane gasoline. That is, 92 octane gasoline contains 92% isooctane, while 95 octane gasoline has an octane level of 95%. Different fuel prices: The unit price of 92 octane gasoline is cheaper than that of 95 octane gasoline.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.