What Happens When Engine Oil Decreases?

What are the scoring rules for the reverse parking in Subject 2?

Subject 2 reverse parking scoring rules. To better observe the situation at the bottom of the left rearview mirror, it is recommended to adjust the left rearview mirror to the highest position before reversing, so that the left bottom line of the parking space can be seen in time. The biggest trick for Subject 2 is to slow down the vehicle speed, always apply a little brake, and maintain a calm mindset. Additional information is as follows: 1. Candidates should note: Candidates need to be aware that each test item starts when the vehicle passes the starting dotted line and the computer announces the test begins; the test ends when the vehicle passes the ending dotted line and the test score is announced (any disqualifying mistakes during the test will immediately end the test). 2. Midway stops or crossing lines: Mistakes such as stopping midway or crossing lines in the section between the ending dotted line of the previous test and the starting dotted line of the next test will not be counted in the score.

4

5

Share

Is the Audi Q5L a domestically produced vehicle?

Audi Q5L is a domestically produced vehicle, manufactured by FAW-Volkswagen Audi. Below is relevant information about the Audi Q5L: 1. Body dimensions: The Audi Q5L measures 4765 mm in length, 1893 mm in width, 1659 mm in height, with a wheelbase of 2908 mm. 2. Powertrain: It is equipped with two engines, one being a low-power version 2.0-liter turbocharged engine, and the other a high-power version 2.0-liter turbocharged engine. The low-power version 2.0-liter turbocharged engine has a maximum power of 140 kW and a maximum torque of 320 Nm, paired with a 7-speed dual-clutch transmission. The high-power version 2.0-liter turbocharged engine delivers a maximum power of 185 kW and a maximum torque of 370 Nm, also matched with a 7-speed dual-clutch transmission.

3

0

Share

How many items are there in B2 subject 3?

According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses", the road test items for B2 subject 3 include: preparation before getting on the car, starting, driving straight, shifting gears, changing lanes, parking by the roadside, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and driving at night. According to the annex of the "Regulations on the Application and Use of Motor Vehicle Driving Licenses": B2 driving license holders can drive heavy and medium-duty trucks; heavy and medium-duty special operation vehicles. Other permitted driving models include: C1, C2, C3, C4, M. Notes for B2 subject 3: Starting: Close the door, fasten the seat belt, turn on the left turn signal, shift to 2nd gear, honk three times, observe the left rearview mirror, slowly release the clutch, accelerate, and release the parking brake to start, no rolling back; Going straight through intersections: Speed should not exceed 30 or be below 20, no crossing the yellow line; Bus stops: Speed should not exceed 30 or be below 20, no crossing the yellow line; Turning right at intersections: Turn on the left turn signal 3 seconds in advance, speed should not exceed 30 or be below 20, no crossing the line; Changing lanes: Turn on the left turn signal 3 seconds in advance, speed should not exceed 30 or be below 20, no crossing the edge line; Overtaking: Turn on the left turn signal 3 seconds in advance, speed should not exceed 30 or be below 20, no crossing the edge line; Turning left at intersections: Turn on the left turn signal 3 seconds in advance, speed should not exceed 30 or be below 20, no crossing the line; Passing school zones: Speed should not exceed 30 or be below 20, no crossing the line, no honking; Driving straight: Shift to 5th gear when speed exceeds 40, speed should be above 40, no crossing the line; Accelerating: Shift to 5th gear when speed exceeds 40, speed should be above 40, no crossing the line; Making U-turns: Choose a suitable section, turn on the right turn signal, move to the far right lane, stop, turn on the left turn signal, shift to 2nd gear, two advances and one reverse to make a U-turn, no rolling back; Parking by the roadside: Turn on the right turn signal for 3 seconds, then park by the roadside, the right wheel should not be more than 30 cm from the roadside line, pull the parking brake, shift to neutral. B2 subject 3 scoring standards: The following situations will result in immediate failure: Not using the seat belt as required; Blocking or turning off the in-car audio and video monitoring equipment; Not following the examiner's instructions; Rolling back more than 30 cm when starting; Using a gear that does not match the speed for a long time, causing the engine speed to be too high or too low; Failing to shift gears twice in a row while driving; Coasting in neutral while driving; Not following traffic lights, signs, or markings; Not driving at the required speed; Driving over the solid center line or edge line of the lane; Driving over the lane dividing line for a long time (more than 15 seconds); Changing two or more lanes in a row; Parking in no-parking zones such as pedestrian crossings or grid lines; The examinee does not attend the exam at the scheduled time; The following situations will result in a 10-point deduction: Rolling back when starting, but less than 30 cm; Shifting to the wrong gear when starting or driving; Not using or incorrectly using the turn signal before starting, turning, changing lanes, overtaking, or parking; Turning the steering wheel less than 3 seconds after turning on the turn signal before starting, turning, changing lanes, overtaking, or parking; Stalling the engine once due to improper operation. Preparation before getting on the car: Not checking the vehicle's exterior and surroundings by walking around the car counterclockwise will result in failure. The following situations during starting will result in immediate failure: Starting with insufficient brake pressure; Starting with the door not fully closed; Not shifting to neutral when starting the engine; Starting without releasing the parking brake and not correcting it in time; The following situations will result in a 10-point deduction: Starting without releasing the parking brake but correcting it in time; Not releasing the starter switch in time after the engine starts. Shifting gears: Not shifting gears smoothly as instructed will result in failure; Vehicle speed not matching the gear will result in a 10-point deduction. Parking by the roadside: After parking, the vehicle body exceeding the right edge line of the road or the pedestrian crossing line will result in failure; Not closing the door after getting off will result in failure; After parking, the distance between the vehicle body and the right edge line of the road or the sidewalk edge being more than 30 cm will result in a 10-point deduction; Not pulling the parking brake after parking will result in a 10-point deduction; Releasing the brake pedal before pulling the parking brake will result in a 10-point deduction; Not turning off the engine before getting off will result in a 5-point deduction. Going straight through intersections, turning left at intersections, turning right at intersections: Not slowing down or stopping to observe as required will result in failure. Passing pedestrian crossings, school zones, bus stops: Not slowing down as required will result in failure.

4

1

Share

Can You Drive a Lynk & Co Without the Car Key?

My personal understanding is that the complete statement should be: To drive the vehicle, the key must be inside the car to complete the engine start-up. After the engine is started, the key can be removed from the vehicle, at which point there will be a warning that the key is not in the car, but this does not affect the vehicle's operation. If the App is used to remotely unlock the doors and start the engine, you can enter the car, and the engine will operate normally with the air conditioning and lighting systems functional, but you cannot shift gears, thus making it impossible to drive the vehicle. Therefore, the conclusion is as follows: The key must be inside the car and detected by the system to obtain permission to shift gears and to drive the vehicle. Using the App to open the door and start the engine does not allow gear shifting because there is no valid authorization confirming the key's presence inside the car.....

18

4

Share

What does the B gear mean?

B gear refers to engine braking. The B gear on a car is a rarely seen gear position, which generally appears on Japanese cars. Toyota's hybrid models are equipped with the B gear, such as the Toyota Corolla, Toyota Prius, and Lexus 200h. This gear can be used when going downhill, equivalent to the L gear on a car. When driving downhill with the B gear engaged, the motor intervenes to achieve engine braking, thereby reducing the car's speed. If the car is traveling on a long downhill section, relying solely on the braking system to slow down is very dangerous. If only the braking system is used for deceleration, the car's brake discs and pads may overheat, and in severe cases, this can lead to brake failure. Many automatic transmission models are equipped with an L gear, which stands for "low," meaning low-speed gear. When driving downhill, using the L gear keeps the car's transmission in a lower gear, allowing the engine's braking effect to slow the car down.

11

4

Share

Is an Engine with Cylinder Blowout Considered Scrapped?

An engine after a cylinder blowout is essentially scrapped. Even if it can be repaired, the operational condition of the repaired engine is unlikely to return to its original level. Not only can high loads cause engine cylinder blowout, but factors like water ingress can also trigger it. However, it's certain that when an engine develops issues, such as cylinder scoring, stopping immediately and preventing the engine from continuing to operate can allow for repairs. The consequence of forcing operation is engine cylinder blowout. Relevant information is as follows: 1. Engine Cylinder Blowout: So-called engine cylinder blowout refers to the piston getting stuck in the cylinder. The cause of the failure is mostly due to the piston lacking oil cooling, overheating, expanding, and seizing in the cylinder, preventing the engine from continuing to operate. 2. Vehicle Malfunction: Engine cylinder blowout is a relatively severe type of vehicle malfunction and one of the most difficult to handle. Repairing an engine with cylinder blowout is considered a major overhaul, with higher repair costs depending on the actual extent of the damage.

2

4

Share

What Happens When Engine Oil Decreases?

What are the scoring rules for the reverse parking in Subject 2?

Is the Audi Q5L a domestically produced vehicle?

How many items are there in B2 subject 3?

Can You Drive a Lynk & Co Without the Car Key?

What does the B gear mean?

Is an Engine with Cylinder Blowout Considered Scrapped?

What is an ETCa Card?

How to Adjust Belt Misalignment?

What are the dangers of sleeping in a car with the air conditioning on?

What are the instructions for the central control buttons of the Fengjun 7?