What engine is used in the BYD G3R?

1 Answers
McAnthony
07/29/25 10:45pm
The BYD G3R is equipped with two types of engines: a 1.5-liter naturally aspirated engine and a 1.8-liter naturally aspirated engine. The 1.5-liter naturally aspirated engine delivers a maximum power of 109 horsepower and a maximum torque of 144 Nm, with the maximum power achieved at 5,800 rpm and the maximum torque at 4,800 rpm. The 1.8-liter naturally aspirated engine produces a maximum power of 122 horsepower and a maximum torque of 160 Nm, with the maximum power reached at 6,000 rpm and the maximum torque between 3,700 to 4,200 rpm. This engine is paired with a CVT transmission.
Was this review help?
19
1
Share
More Forum Discussions

What are the disadvantages of adding OBD one-touch window lift?

obd one-touch window lift disadvantage is that when the first window of the car has reached the closed state within 5 seconds, the controller cannot determine the disconnected state and will continue to supply power to the window motor, causing the motor to operate under overload conditions for a long time. Introduction to automotive OBD: Automotive OBD refers to the On-Board Diagnostics system, and the OBD interface in a car is located below the left side of the steering wheel. Function of automotive OBD: The main function is to monitor the operating condition of the engine. During operation, the engine burns fuel and produces exhaust gases. The On-Board Diagnostics system continuously monitors whether the vehicle's exhaust emissions exceed the standard. Once the vehicle's exhaust emissions exceed the standard, the OBD warning light will immediately sound an alarm. The On-Board Diagnostics system can not only detect vehicle exhaust indicators but also monitor the engine, catalytic converter, particulate filter, oxygen sensor, emission control system, fuel system, etc., to identify potential safety hazards in the vehicle at any time and ensure the vehicle's safety performance.
6
4
Share

Why Doesn't the Manual Transmission Automatically Return to Neutral?

During driving, manual transmissions generally do not need to return to neutral, as this can affect the vehicle's transmission. Gear Positions: Vehicle gear positions typically consist of D (Drive), R (Reverse), P (Park), N (Neutral), and S (Sport) modes. Among these, D is for forward driving, R is for reversing, P is for parking, N is neutral, and S is the sport mode (available in models equipped with a sport mode). Precautions for Gear Usage: The vehicle must come to a complete stop before shifting into P (Park) mode; otherwise, the mechanical parts of the automatic transmission may be damaged. When the vehicle is parked and not in use, engaging P mode mechanically locks the wheels, and using the handbrake in conjunction can prevent rolling. Damage may occur otherwise.
13
5
Share

Does the owner need to accompany the tow truck?

Does the owner need to accompany the tow truck? Introduction to tow trucks: A tow truck, also known as a tractor, is a large truck or semi-trailer that uses tools to tow between the cab and the trailer. The cab can detach from the original trailer and tow other trailers, and the trailer can also detach from the original cab and be towed by other cabs. The front part with driving capability is called the tractor, and the rear part without driving capability is called the trailer, which is pulled by the tractor. Regulations during towing: The towed vehicle must not carry any passengers other than the driver and must not tow another trailer. The width of the towed vehicle must not exceed the width of the towing vehicle.
13
0
Share

What Causes a Sudden Loss of Speed in a Motorcycle?

There are several reasons why a motorcycle may suddenly lose acceleration. Clogged Air Filter: Once the air filter is clogged, the engine's air intake is restricted, leading to incomplete combustion and reduced combustion efficiency, which inevitably affects acceleration performance. Fuel System Not Cleaned for a Long Time: Both fuel injection systems and carburetors require regular cleaning, with carburetors needing more frequent cleaning. Ignition System Issues: If there is a noticeable jerking sensation while riding, there is an 80% chance the problem lies in the ignition system. The most common components to fail in the ignition system are the ignition coil, high-voltage coil, and connecting wires. Engine Problems: Valve leakage, worn piston rings, and aging cylinders can all cause the engine to lose acceleration power. This is mainly due to decreased cylinder pressure, which alters the engine's combustion state, resulting in poor acceleration performance.
12
5
Share

What Causes the Motorcycle Rear Wheel to Not Move?

Reason is that the motorcycle is in gear, you need to shift out of gear to freely push the motorcycle. Additional Information: Motorcycle Power: The main power source of a motorcycle comes from the engine, where the movement of the crankshaft and piston generates power, and the crankshaft transmits this power to the clutch. Motorcycle Maintenance Methods: Regularly lubricate the motorcycle's chain; clean the front and rear wheels to prevent mud, plastic bags, and other debris from getting tangled; avoid carrying excessively heavy loads to prevent shortening the motorcycle's lifespan; clean the exhaust pipe to avoid clogging; wash the motorcycle regularly; use synthetic oil for lubrication, as synthetic oil provides better lubrication than regular oil; when washing the motorcycle, try to avoid water entering the horn and other electronic components.
15
5
Share

What is a Blown Cylinder Head Gasket?

Reasons for a blown cylinder head gasket: Improper driving: Incorrect driving techniques, such as frequent sudden acceleration or prolonged high-speed driving, can cause excessive pressure that accelerates the erosion of the cylinder head gasket. Poor quality: Low-quality cylinder head gaskets with uneven thickness, air pockets in the sealing edges, uneven asbestos distribution, or loose edges; warped cylinder heads. Excessive deviation in the cylinder block flatness, loose individual cylinder bolts, or bolts stretched and plastically deformed can all lead to poor sealing. Engine overload: Operating the engine under heavy load for extended periods or frequent detonation can result in high temperature and pressure within the cylinders, leading to the erosion of the cylinder head gasket.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.