What engine is in the Roewe RX5?

How to Adjust the Seat?

Methods for adjusting the seat: 1. Move the front seat forward or backward by pulling up the lever and moving the front seat. After releasing the lever, the front seat must lock into place. 2. Adjust the lumbar support by turning the lever to change the angle of the lumbar support. 3. Adjust the seat back by pressing down the lever and adjusting the seat back. After releasing the lever, the seat back must lock into place. 4. Adjust the seat height by repeatedly lifting or pressing down the lever to set the seat to the desired height. In addition to seat adjustment, the steering wheel and seat belt adjustments are also crucial. The position of the steering wheel should be adjusted based on the seat position. If the steering wheel is too close to the body, it may increase the risk of injury when the airbag deploys. If it is too far, it may lead to misoperation in emergency situations. Seats are generally divided into two types: leather seats and fabric seats.

14

3

Share

What is the stop-start fault?

stopstart is a mandatory parking warning light, which should illuminate simultaneously with one of the warning lights such as low oil pressure, low brake fluid level, or high water temperature, indicating that the engine must be stopped. This warning light is connected to the "engine oil pressure," "low brake fluid level," "coolant temperature gauge," and "electronic brake force distribution system fault" warning lights. Additional information: 1. Exhaust temperature warning light: When the exhaust temperature warning light comes on, the driver should immediately reduce speed or stop the vehicle. Once the exhaust temperature decreases, the warning light will automatically turn off (however, a fuse-type exhaust temperature warning light will remain on if not adjusted or repaired. If the exhaust temperature warning light does not turn off, the cause should be identified and the fault resolved before continuing to drive. 2. Brake warning light: The brake warning light is red and features a "!" symbol inside a circle. If the red brake warning light illuminates, it indicates the following conditions in the braking system: severe wear of the brake pads, low brake fluid level, etc.

16

3

Share

Why does the Sylphy lack power during acceleration?

Here are the possible reasons for the Sylphy's lack of power during acceleration: 1. Fuel system malfunction: Throttle carbon deposits mainly affect idle instability and have little impact on engine acceleration performance. A clogged or waterlogged air filter reduces air intake, leading to an overly rich fuel mixture, incomplete combustion, and poor acceleration, often accompanied by severe black smoke from the exhaust pipe. Fuel pipe cracks or loose joints causing air leaks, along with insufficient fuel pump pressure, result in poor fuel delivery and affect acceleration power. 2. Electrical system malfunction: Issues with the mass airflow sensor can reduce air intake, causing the fuel mixture to be either too rich or too lean, affecting acceleration performance. Damage to individual cylinder spark plugs (i.e., misfiring) also impacts acceleration. Other issues include leaking ignition wires. Overheating or a faulty temperature sensor similarly affects acceleration performance. 3. Mechanical malfunction: Wear and tear on engine valves, cylinder liners, pistons, and rings can lead to insufficient cylinder pressure. Excessive intake valve clearance or insufficient exhaust valve clearance can also be contributing factors.

15

4

Share

What Causes Abnormal Noises from the Car Chassis?

Possible causes of abnormal noises from the car chassis are as follows: 1. Noises during vehicle startup are generally due to suspension system faults, or may be caused by loose or damaged engine mounts. 2. Noises during vehicle steering may be due to faults in the steering system or suspension system. During steering, the vehicle's tilt causes deformation in the suspension system, which also participates in the movement. 3. Noises during driving on good road conditions may be due to faults in the braking system components, such as loose or worn parts, out-of-round brake drums, or uneven brake discs. 4. Issues with the bearings connecting moving and stationary parts. If it's a bearing problem, the driver can identify it by applying slight braking; if the noise remains unchanged during uniform motion with braking, it indicates a bearing issue. 5. Noises during driving on poor road conditions are mostly due to suspension system problems, or may be caused by loose braking system components.

7

2

Share

What does it mean when the rear car flashes high and low beams alternately?

The rear car flashing high and low beams alternately is a signal to the front car owner to indicate an intention to overtake, requesting the front car owner to pay attention and yield. Meaning of alternating high and low beams: Alternating between high and low beams is used for nighttime encounters with oncoming traffic, as an overtaking signal, or to switch between high and low beams to serve as a warning. Usage of alternating high and low beams: High beams should be turned on in poor lighting conditions, such as on highways or rural roads. In well-lit conditions, or when encountering oncoming traffic, following another vehicle, pedestrians, or non-motorized vehicles, switch to low beams. This is especially necessary on urban roads with streetlights. It is particularly important to flash the lights when overtaking large trucks, as they have large blind spots and high chassis. Repeated flashing is needed to alert the truck driver and ensure safety before overtaking.

19

2

Share

How many points are deducted for crossing a yellow line?

Generally, driving over a single yellow line results in a traffic penalty of 3 points deducted. Crossing a yellow line is a violation of traffic rules. Yellow lines are divided into single yellow lines and double yellow lines, neither of which allows vehicles to drive over or cross the line. If violated and recorded by traffic police or cameras, a traffic penalty of 3 points will be imposed. Below is an introduction to the traffic rules regarding yellow lines: 1. Solid lines strictly prohibit crossing: Whether it's a single or double yellow line, as long as it's a solid line, crossing is strictly prohibited, such as for overtaking, turning, or making a U-turn. Under normal driving conditions, there should be no reason to cross the line. 2. Dashed lines allow U-turns: Whether it's a single or double yellow line, as long as it's a dashed line, overtaking or making a U-turn is permitted under safe conditions.

15

5

Share

What engine is in the Roewe RX5?

How to Adjust the Seat?

What is the stop-start fault?

Why does the Sylphy lack power during acceleration?

What Causes Abnormal Noises from the Car Chassis?

What does it mean when the rear car flashes high and low beams alternately?

How many points are deducted for crossing a yellow line?

What does 'nokey' displayed on the car mean?

Which Car Brand Has a Diamond Logo?

What Causes High Idle Speed in Small Cars?

Where is NIO's electric SUV produced?