What engine is equipped in the BYD Surui?

1 Answers
LucilleMarie
07/25/25 3:49am
BYD Surui is equipped with a 1.5-liter naturally aspirated engine, which has a maximum power of 109 horsepower and a maximum torque of 145 N·m. It features VVL (Variable Valve Lift) technology and multi-point fuel injection technology, and uses an aluminum alloy cylinder head and block. This engine is paired with a 5-speed manual transmission. The front suspension of the BYD Surui uses a MacPherson independent suspension, while the rear suspension uses a torsion beam non-independent suspension. The BYD Surui is a compact car under the BYD brand, with dimensions of 4680mm in length, 1765mm in width, and 1490mm in height, and a wheelbase of 2660mm.
Was this review help?
16
3
Share
More Forum Discussions

Does accidentally starting the car in gear have any impact on the vehicle?

It depends on the situation. Normally, if the clutch is fully depressed, starting the car in gear won't have any impact. However, if the clutch is not depressed or not fully engaged, directly starting the car can damage the starter, brake system, and may cause the vehicle to lurch forward, increasing the risk of an accident. When starting on a steep slope, engaging the first gear is necessary to prevent the vehicle from rolling back, but the clutch must still be depressed while starting. Additional information: For manual transmission vehicles, it's recommended to depress both the clutch and brake pedals when starting. Depressing the clutch pedal while starting is equivalent to starting in neutral, as it cuts off the power transmission, and strictly speaking, it won't harm the vehicle.
8
5
Share

What Does Label Removal Mean?

It means the device is currently unavailable and needs to be reinstalled and reactivated at the original processing point or any expressway ETC service office. Here is additional information: Most ETC devices display "label removal" because users dismantled the ETC equipment to replace the battery. Recovery method: The anti-tamper lever on the back of the ETC electronic tag is essentially a reset button switch. Once the button pops out, the information stored in the ETC device will be erased, requiring reactivation to input the data again. You can try the ETC self-service activation method. If that doesn't work, you'll need to take it to an ETC service point or ETC service center for reactivation or cancellation, and replace it with a new ETC electronic tag.
7
4
Share

What Causes Excessive Transmission Oil Temperature?

Here are the reasons for excessive transmission oil temperature: Transmission oil level too high or too low: Check the oil level in the transmission oil pan and adjust the transmission oil to the specified level. Damage to the transmission pump or blockage in the oil suction line: The transmission pump controls the distribution of high-pressure oil generated by the torque converter through the transmission distribution valve to the second shaft assembly, enabling the loader to move forward and backward. Damage to the transmission pump can lead to insufficient oil supply to the transmission. With prolonged use of the loader, increased wear can cause internal leakage in the transmission pump, resulting in insufficient transmission pressure and mechanical efficiency. This can lead to poor oil supply in the suction line, preventing the oil from lubricating moving parts and increasing friction, which also causes system overheating. It is important to note that air leaks or blockages in the transmission pump suction line can also cause insufficient flow, leading to excessively high oil temperature.
3
4
Share

What Causes Transmission Gear Jumping?

Transmission gear jumping can be attributed to the following main causes: Fixing Screws: Loose fixing screws or bolts between the transmission and clutch housing. Failure of the transmission shift fork shaft self-locking mechanism. Deformation or looseness of the lower end of the gearshift lever or its ball joint. Shifting: The transmission shift fork is bent, severely worn, or its fastening screws are loose, preventing gears from engaging properly. Synchronizer: Loose, disassembled, or weakened positioning springs in the lock-pin type inertial synchronizer. Excessive wear of the lock ring teeth or the internal tapered surface thread grooves in the lock ring type synchronizer. Bearings: Excessive wear or looseness in bearings, causing gears to swing up and down instead of meshing correctly.
12
0
Share

Is Transmission Water Damage Covered by Insurance?

If you have purchased water damage insurance, damage to the car's transmission and engine due to water ingress is covered under the insurance policy. Relevant information is as follows: Additional Insurance: Water damage insurance is an additional coverage, and additional insurance for motor vehicles is an important part of motor vehicle insurance. According to China's current motor vehicle insurance clauses, the main additional coverages include theft insurance, spontaneous combustion loss insurance, water driving loss insurance, newly added equipment loss insurance, no-deductible special agreement insurance, driver accidental injury insurance, and designated repair shop insurance, among others. Insurance customers can choose to add these coverages based on their needs. Water-Induced Stalling: When a vehicle stalls due to driving through water, there is a 50% probability of engine damage; however, if the engine is restarted after stalling, the engine is certain to be damaged. Insurance companies do not cover engine damage caused by forced ignition.
14
4
Share

Will There Still Be Problems After Transmission Water Ingress Repair?

There are usually no problems after repairing a water-ingressed transmission. A properly repaired transmission will not have sequelae; those with sequelae are due to incomplete repairs. The transmission is a very important component of a vehicle, capable of changing the gear ratio and expanding the torque and speed of the driving wheels. Relevant information about the transmission is as follows: Introduction: A device that changes the speed ratio and direction of motion. It is used to alter the torque, speed, and direction of motion transmitted from the driving shaft to the driven shaft under different working conditions. A gear-driven transmission generally consists of a casing and several gear pairs. Function: During vehicle operation, to adapt to different working conditions, the driving force and speed of the vehicle need to vary within a certain range. However, the existing engine's torque and speed variation range cannot meet this requirement, hence the installation of a transmission.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.