What engine does the Geely Emgrand have?

Can the Buick Excelle continue to drive when the engine yellow light is on?

The engine yellow light on the Buick Excelle indicates that there is a problem with a certain part of the vehicle, but it is not too serious. You can continue to drive, but it is necessary to go for repair as soon as possible. Reasons for the Buick Excelle engine yellow light being on: Sensor issues: When sensors such as the water temperature sensor, crankshaft position sensor, air flow sensor, intake air temperature sensor, or oxygen sensor are damaged, have poor contact, or signal interruption, the car's ECU cannot accurately obtain the engine's data, which will cause the engine fault light to turn yellow and illuminate. Fuel quality issues: If the car is not filled with the corresponding model of fuel as required, it will cause engine wear over time, leading to the fault light turning on. Poor combustion of the air-fuel mixture: Engine problems such as spark plug failure, ignition coil failure, fuel pump failure, or fuel line blockage can all cause poor combustion of the air-fuel mixture in the engine. Poor combustion of the air-fuel mixture leads to engine carbon deposits or knocking problems. When detected by the engine's oxygen sensor, the fault light will illuminate as a warning.

7

5

Share

What's the reason when the car won't start?

Here are the reasons why the car won't start: 1. First, check the spark plugs. Since spark plugs are crucial to the car's ignition system, and the ignition system is key to the engine's operation, the performance of the spark plugs directly affects the overall working performance and efficiency of the vehicle. 2. Battery depletion – The symptoms include the starter motor turning but not fast enough (lacking power), and eventually, the starter motor only makes a clicking sound without turning. Low temperatures in winter or forgetting to turn off certain electrical devices can prevent the car from starting, especially when the vehicle is used for short, low-speed trips over a long period in winter, causing the battery voltage to drop below the rated value. If this happens, call the service station for assistance, jump-start the car, or temporarily start it, and then make sure to recharge the battery at the service station. 3. Fuel flow blockage – The symptom is no oil pressure in the engine's fuel supply line. This situation often occurs on extremely cold mornings due to long-term dirt buildup in the fuel lines. When temperatures are extremely low, water and debris mix and block the fuel lines, preventing the car from starting. Emergency solutions: Move the car to a warmer environment, and it should start after a while; or thoroughly clean the fuel lines to resolve the issue.

6

2

Share

What tools are needed to replace the battery in a Cadillac XT5 key?

Cadillac XT5 key battery replacement requires the use of a screwdriver and a new battery. There are two screws on the back cover of the car key. Use the screwdriver to remove the screws separately, then open the back cover to see the battery panel. Remove the old battery and install the new one. Reattach the back cover and tighten the screws. Notes on battery replacement: When replacing the battery, be careful not to damage the chip. If the chip is damaged, it will need to be reconfigured. When using the remote key in daily life, avoid repeated or long-distance remote operations, as these actions can accelerate battery consumption. Also, avoid exposing the key to water, as most car remote key casings are not waterproof. When not in use, store the remote key properly. What to do when the remote key runs out of power: You can use the mechanical key to unlock the car door. If your car is equipped with a keyless start system, there is a designated key-sensing area inside the car. After the remote key runs out of power, placing it in this designated area can still start the engine. Once the remote key is out of power, replace the battery immediately to avoid affecting normal vehicle use.

15

0

Share

What are the reasons why the Bora cannot engage reverse gear?

The Bora cannot engage reverse gear for four reasons: first, the gear is not properly engaged and is still in neutral; second, the handbrake is not released; third, the clutch is not disengaged; fourth, the synchronizer in the transmission is stuck. Main uses of reverse gear: The function of reverse gear is not simple—it allows the vehicle to move in the opposite direction, enabling backward movement, a feature indispensable for any car. In manual transmission models, reverse gear also serves as a hill-holding brake; when parking on a downhill slope, engaging reverse gear can mechanically lock the drive shaft. How to use reverse gear: For manual transmission vehicles, after coming to a complete stop, first press the clutch and brake, then engage reverse gear, followed by a slight throttle operation with partial clutch engagement. For automatic transmission vehicles, the brake pedal must be pressed, and the safety button on the gear lever must be pressed or the gear shift lever must be pushed down to engage or disengage the R (reverse) gear. Both P (park) and N (neutral) gears can be directly switched to R gear, but when switching between forward gears and R gear, it is advisable to pause at N gear to reduce the impact of reverse oil flow in the transmission during gear shifting.

17

5

Share

How to Switch Between Passat Seat Ventilation and Heating?

The Volkswagen Passat's seat ventilation and heating functions can be toggled via the buttons on the vehicle's air conditioning control panel. When the seat ventilation function is activated, the seat heating function turns off, and vice versa. These two functions cannot be operated simultaneously. The activation condition is that the vehicle needs to be powered on but does not require the engine to be running. Seat Heating Working Principle: The seat is embedded with resistance heating wires, which are sewn into the seat cover. Heating is achieved by electrifying these resistance wires, causing the seat to gradually warm up within a short time. Temperature sensors installed within the heating pads monitor changes in seat temperature, thereby controlling the power supply to the heating wires to maintain the seat heating temperature within an appropriate range. Seat Ventilation Working Principle: The seat cushion and backrest are equipped with ventilation systems that use fans to draw in air and direct it into a ventilation layer. Airflow then permeates upward through perforations on the seat surface, blowing toward the seat surface. To accommodate the fans, the internal structure of the seat must be modified. Factors such as fan noise and vibration, ventilation volume, and cooling speed must also be considered. The foam and upholstery of ventilated seats require special structures to meet ventilation needs.

6

3

Share

What is the principle of a car tire pressure detector?

Car's built-in tire pressure monitoring can be divided into two types: direct tire pressure monitoring and indirect tire pressure monitoring. Both can detect tire pressure, the difference is that the direct type can display specific tire pressure values, while the indirect type only reminds that there is a problem with the tire pressure. Here is a brief introduction to tire pressure monitoring: 1. Direct tire pressure monitoring Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire's air pressure, and use a wireless transmitter to send the pressure information from inside the tire to a central receiver module, which then displays the tire pressure data for each tire. When the tire pressure is too low or there is a leak, the system will automatically alarm. 2. Indirect tire pressure monitoring The working principle of indirect tire pressure monitoring is: when the pressure of a certain tire decreases, the weight of the vehicle will cause the rolling radius of that wheel to become smaller, resulting in its rotation speed being faster than other wheels. By comparing the difference in rotation speed between tires, the purpose of monitoring tire pressure is achieved. The indirect tire alarm system actually relies on calculating the rolling radius of the tire to monitor the pressure. Whether it is direct tire pressure monitoring or indirect tire pressure monitoring, both are very necessary for the safety of car driving.

17

4

Share

What engine does the Geely Emgrand have?

Can the Buick Excelle continue to drive when the engine yellow light is on?

What's the reason when the car won't start?

What tools are needed to replace the battery in a Cadillac XT5 key?

What are the reasons why the Bora cannot engage reverse gear?

How to Switch Between Passat Seat Ventilation and Heating?

What is the principle of a car tire pressure detector?

What are the reasons for the BYD S6 air conditioner not cooling?

Why Does a Car Drip Water After Stopping in Winter?

What are the differences between IndyCar and F1?

How to Deal with a Damaged BMW Gasoline Particulate Filter?