What engine does the BMW X4 use?

1 Answers
LeLucas
07/23/25 8:31pm
BMW X4 is equipped with a 2.0T turbocharged engine, and BMW X4 has launched one power model. This engine is divided into a high-power version and a low-power version. The maximum power of the 2.0T low-power engine is 135 kilowatts, and the maximum torque is 290 Newton-meters; the maximum power of the 2.0T high-power engine is 185 kilowatts, and the maximum torque is 350 Newton-meters. BMW X4 is a mid-size SUV launched by BMW, which provides a unique xDrive all-wheel drive system, making its performance in terms of power more outstanding. The driving mode of BMW X4 is front-engine four-wheel drive, and the four-wheel drive form is on-demand four-wheel drive. The front suspension of this car uses a double-joint spring strut front axle suspension, and the rear suspension uses a five-link rear suspension. The car's chassis has been specially tuned to reduce the car's roll during acceleration and cornering.
Was this review help?
12
3
Share
More Forum Discussions

Is a tire pressure of 2.7 too high in summer?

Summer tire pressure of 2.7 is very high. According to the international GBT2978-2008 standard, the standard tire pressure for standard tires is 2.4-2.5 bar. A pressure of 2.7 bar exceeds the maximum value of the standard tire pressure, so it is abnormal. Generally, the lower limit of the standard tire pressure for car tires is sufficient. For example, the lower limit for standard tires is 2.4 bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1 bar lower than the standard to avoid tire blowouts due to high temperatures. Hazards of excessive tire pressure: The friction and adhesion of the tire will decrease, affecting braking performance; It can cause steering wheel vibration and deviation, reducing driving comfort; Accelerates localized wear on the central tread pattern, shortening tire lifespan; Increases vehicle vibration, indirectly affecting the lifespan of other components; Causes excessive stretching and deformation of tire cords, reducing tire elasticity and increasing the load on the car during driving; Decreases puncture resistance. When encountering sharp objects like nails or glass on the road, they can easily penetrate the tire, causing internal cracks and blowouts due to impact.
3
5
Share

Is it necessary to repair a malfunctioning ESP?

ESP malfunctions require repair. During vehicle operation, the ESP system continuously monitors the driver's steering direction, speed, throttle opening, braking force, as well as the vehicle's tilt angle and roll rate through various sensors. It assesses the discrepancy between safe driving conditions and the driver's intended maneuvers. The system then adjusts engine speed and distributes braking force to individual wheels to correct oversteer or understeer. ESP significantly enhances driving stability. Key features of ESP include: 1. Real-time monitoring: ESP constantly tracks the driver's inputs, road conditions, and vehicle dynamics, sending continuous commands to the engine and braking systems. 2. Active intervention: Unlike safety technologies such as ABS which primarily intervene in the driver's actions, ESP can regulate engine output.
19
3
Share

What Causes Slow Cooling of Car Air Conditioning After Prolonged Sun Exposure?

Car air conditioning cools slowly after prolonged sun exposure due to the compressor protection device tripping. Causes and solutions for excessively high pressure and overheating: 1. Excessive refrigerant: Appropriately reduce the refrigerant amount. 2. Poor heat dissipation: Check for dirt on condenser pipes and clean the condenser. 3. Blocked pipeline system: Refer to pressure gauge readings for diagnosis and resolution, then reprocess the system. 4. Dust accumulation on evaporator or filter: Reduced airflow causes system pressure and temperature imbalance; clean the evaporator or filter. 5. Possible refrigerant deficiency: When refrigerant is insufficient, compressor exhaust temperature becomes excessively hot, causing the overload protection switch to trip.
6
3
Share

What is the cross-sectional area of car battery cables?

For small passenger vehicles, the national standard recommends pure copper cables with a cross-sectional area of 16 square millimeters. However, for large engineering vehicles, the recommended national standard is 25 square millimeters of pure copper. If the cable size falls below the recommended value, it may be difficult to jump-start the engine. With constant power and voltage, thicker cables have lower resistance, ultimately delivering greater current to the starter motor. Additional information: Precautions for using car batteries: Ensure the auxiliary battery is 12V and the negative terminal is properly grounded. Of course, all unnecessary lights and accessories should be turned off to prevent electrical accidents. Never reverse the polarity of the cables, as this may cause sparks during connection. Additionally, make sure the cables are tightly secured to both battery terminals (for full contact) to avoid sparking during the jump-start process.
19
0
Share

What are the types of car accidents?

Car accidents are classified according to their consequences as follows: 1. Minor accidents: These refer to accidents that cause minor injuries to 1 or 2 people, or involve relatively small property damage. 2. General accidents: These refer to accidents that cause serious injuries to 1 or 2 people, or minor injuries to 3 or more people, or involve average property damage. 3. Major accidents: These refer to accidents that result in the death of 1 or 2 people, or serious injuries to 3 to 10 people, or involve significant property damage. 4. Catastrophic accidents: These refer to accidents that result in the death of 3 or more people, or serious injuries to 11 or more people, or the death of 1 person along with serious injuries to 8 or more people, or the death of 2 people along with serious injuries to 5 or more people, or involve extremely large property damage.
17
2
Share

What are the three filters in the three-filter maintenance?

The three-filter maintenance refers to the maintenance of the engine oil filter, air filter, and fuel filter in a car. 1. Air filter: The function of the air filter is to filter the air before it enters the cylinder, removing impurities, dust, sand, and other foreign particles. 2. Fuel filter: The fuel filter's core is mostly made of filter paper, but some use nylon cloth or polymer materials. Its purpose is to filter out solid impurities such as iron oxide and dust, as well as water from the gasoline. This not only reduces the chance of the fuel injector being clogged by impurities but also ensures the quality of the gasoline flowing into the fuel system. 3. Engine oil filter: Its function is to remove various impurities from the engine oil to ensure the normal operation of the lubrication system.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.