What does trip A/B mean on the car dashboard?

How to Turn Off 4LO on a Prado?

Here are the methods to turn off 4LO on a Prado: 1. Method One: Switch between high-range and low-range 4WD again. During the switching process, rev the engine a few times. If it doesn’t work, lift the vehicle and firmly press the ABS sensor connectors near the front and rear wheels, as well as the 4WD transfer case connector in the middle under the vehicle. 2. Method Two: Disconnect the battery for 10 minutes, then reconnect it to see if it can reset. 3. Method Three: Take it to a repair shop to use a diagnostic tool to read the specific fault codes and then proceed with repairs. Finally, it is recommended to go to a professional repair shop for troubleshooting and repairs for better safety and reliability.

3

Share

Is the rear axle of the Qashqai an independent suspension?

The rear axle of the Qashqai is an independent suspension. Below is relevant information about the rear axle of a car: 1. The rear axle of a car refers to the axle at the rear. 2. In front-wheel-drive vehicles, the rear axle is merely a trailing axle, serving only a load-bearing function. 3. Generally, there is also a transfer case in front of the rear axle. The working principle of the rear axle is as follows: 1. The engine transmits power to the transmission, which then transfers it to the large gear plate on the rear axle (the differential). 2. The differential is an integrated unit, containing small gear plates at the top and bottom with a cross-shaped column in the middle, equipped with two small planetary gears (serving to adjust speed during turns). 3. The differential is positioned vertically, with two small circular holes on each side and sliding keys on top. During straight driving, the cross-shaped column remains stationary, while during turns, it moves to adjust the rotation speeds of the two tires, thereby enhancing the car's maneuverability during turns.

11

2

Share

What are the reasons for incomplete gear engagement in a manual transmission?

Possible reasons for incomplete gear engagement in a manual transmission include: 1. The positioning components of the gear lever's ball joint may have failed. 2. The gear lever may rotate freely around its own axis, making it impossible to control the gear position accurately. 3. The spherical working surface at the lower end of the gear lever may have worn out, preventing the gear lever from controlling the fork or the fork head's slot, leading to failure in gear engagement and disengagement. The former can usually be resolved through repairs, while the latter requires replacement of the gear lever. 4. The clutch may not be fully disengaged, even though the transmission's shifting mechanism is functioning normally. This can be resolved by adjusting the clutch or replacing its components. 5. The fork may be loose, severely bent, deformed, or worn out. While the gear lever moves into position, the fork does not, resulting in severe impact and inability to engage the gear. In such cases, the transmission cover should be opened for inspection and repair, and the fork should be replaced if necessary.

8

0

Share

What does it mean when the TRC OFF light is on?

TRC OFF light on indicates that the vehicle's traction control system is currently turned off. The Traction Control System, abbreviated as TCS, is also known as ASR or TRC. The functions of TRC are: 1. Preventing wheel spin when the vehicle is driving on slippery surfaces such as snow, ensuring smooth starting and acceleration; 2. Controlling the risk of vehicle skidding on steep slopes or rough rocky roads; 3. Applying braking force to limit wheel spin when the drive wheels slip, and ensuring smooth turning when accelerating during a turn.

17

4

Share

What size truck can a B1 driver's license drive?

B1 driver's license can drive trucks with a total mass of 4.5 tons and an approved load capacity of 1.5 tons. Because the permitted vehicle types for B1 do not include those for B2, a B1 license only allows driving light and mini trucks with a total length not exceeding 6 meters, a total mass below 4500kg (including 4500kg), and an approved load capacity below 1500KG. Here are the relevant details about the license: 1. The tonnage of low-speed trucks should not exceed 4.5t, and the designed load capacity generally should not exceed 1.5t. Trucks exceeding the load capacity of 1.5t require a B2, A1, or A2 license to drive. To summarize, the B1 license is intended for driving passenger vehicles, while the B2 license is for driving trucks, and the application threshold for B1 is higher than that for B2. 2. The B2 license can be applied for directly when initially obtaining a driver's license, while the B1 license requires holding at least a C1 license for more than three years or a B2 license for more than two years, with no record of 12 penalty points in the most recent three consecutive scoring cycles. 3. Applying for an upgraded B1 license must be done at the local vehicle management office in the applicant's registered residence. The applicant's age must be between 21 and 60 years old. For those holding a B1 driver's license, if the age exceeds 60, it will be downgraded to a C1 license.

20

2

Share

Will crossing the solid white line always be captured?

Crossing the solid white line will always be captured as the solid line lane-changing photo system uses ground-pressure magnetic induction coils. The principle of photo capture is: when the front wheels of the vehicle cross the induction coil on the ground, the first photo is taken electronically; when the rear wheels of the vehicle cross the induction coil on the ground, the second photo is taken electronically; when the vehicle passes through the intersection and crosses the induction coil on the opposite side of the ground, the third photo is taken electronically. The solid line lane-changing photo system is operational 24 hours a day, and the images and related data are retained for one week. We remind everyone not to take chances, as crossing the solid white line will not be penalized in certain special circumstances and road sections. When encountering special situations ahead, or when there is on-site command by traffic police or special rescue vehicles performing tasks, it is unreasonable to wait until the problem is resolved before proceeding. Therefore, changing lanes over the solid line in such cases will not be considered a violation.

16

3

Share

What does trip A/B mean on the car dashboard?

How to Turn Off 4LO on a Prado?

Is the rear axle of the Qashqai an independent suspension?

What are the reasons for incomplete gear engagement in a manual transmission?

What does it mean when the TRC OFF light is on?

What size truck can a B1 driver's license drive?

Will crossing the solid white line always be captured?

How many liters of transmission fluid does the Teana need?

Does the Lynk & Co 03 Have Ambient Lighting?

What are the symptoms of poor fuel quality?

Can the ETC card be removed when not in use?