What does 'Three Pull Two' mean?

1 Answers
LeMalia
07/30/25 5:08am
'Three Pull Two' refers to a three-kilowatt controller paired with a two-kilowatt motor. The role of the controller: As the brain of an electric vehicle, the controller plays a crucial role in the vehicle. It is the core control device used to manage the motor's start, operation, direction, speed, stop, and other electronic components of the electric vehicle. It functions like the brain of the vehicle and is one of its most important parts. Composition of the controller: In simple terms, an electric vehicle controller consists of peripheral components and a main chip. The peripheral components are functional elements such as actuators and sensors, including resistors, sensors, bridge switch circuits, and other devices that assist the microcontroller or dedicated integrated circuit in completing the control process.
Was this review help?
12
3
Share
More Forum Discussions

How to Replace the Key Battery for Chery Ant?

Push the marked switch upwards from the tail of the key, and the hidden mechanical key will pop out slightly. Then, remove the mechanical key. After removing the hidden mechanical key, insert it into the hole on the right side to slightly open the back cover. Once the back cover is opened, you will see a lithium battery positioned quite deep inside. Use a tool to slide along the gaps on both sides to remove and replace the battery. When installing the new battery, ensure that the positive and negative terminals are not reversed. Close the back cover and reinsert the mechanical key.
6
3
Share

How to Remove Hardened Cement from a Car?

Mainly, hot water can react with a certain component in the cement, making it brittle. First, cover the cement spots with a towel, pour hot water over them, and wait a while for the cement to become brittle. First, you need a small spray bottle (like a gel bottle) filled with white vinegar. Spray it on the cement, wait a while, then rinse with water. Repeat a few times. You need to buy a bottle of oxalic acid, then apply it to the cement spots with a towel. Wait a few minutes, scrub with a brush, then rinse with water. The effect is good. Oxalic acid is somewhat corrosive, so safety precautions are necessary when using it.
11
3
Share

At What RPM Does the Turbocharger Kick In?

Engine starts at medium speed, and the turbocharger will activate above 1,500 RPM. Here are some precautions for using a turbocharger: 1. Avoid flooring the accelerator right after starting: Since the turbocharger relies on engine oil for cooling, the oil's fluidity is poor during a cold start. If the turbocharger operates at high speeds under these conditions, it will experience significant wear. Therefore, let the engine idle for two to three minutes first, allowing the oil to fully lubricate before revving the engine. This extends the turbo's lifespan, especially crucial in winter. 2. For manual transmission turbocharged cars, avoid lugging the engine: Lugging occurs when the gear is too high for the actual driving conditions. For example, forcing a high gear while climbing a hill or driving at low speeds, which requires high torque, can cause lugging. This can severely damage the engine and even ruin the spark plugs. 3. Avoid prolonged idling: Many drivers prefer not to turn off the engine while waiting. However, during idling, the engine and turbocharger run at low speeds, causing the gas pressure inside the turbo and compressor to drop below the bearing housing pressure. This can lead to oil leakage into the compressor and turbine, depriving the bearings of proper lubrication and cooling. Additionally, oil leaking into the compressor may enter the cylinders, disrupting the engine's normal operation. Therefore, avoid excessively long idling periods.
8
0
Share

What to Do When a Manual Transmission Car Won't Start Due to a Dead Battery?

Find someone to help push the car to get it started. Once the car reaches a certain speed, shift into gear, quickly release the clutch pedal, and press the accelerator. Once the engine starts, quickly press the clutch pedal while controlling the throttle to prevent stalling, then slowly pull over to the side. Alternatively, find another car nearby with a working battery and a set of jumper cables. Position the cars close together, open the hood, and locate the other car's battery. Connect the jumper cables to both batteries, positive to positive and negative to negative, effectively linking the two batteries in parallel.
17
0
Share

How to Remove the Battery from a Golf Key Fob?

Use a screwdriver to gently pry open the back cover of the key fob. Push it lightly and gradually remove it. Avoid using excessive force; instead, apply a bit of finesse to take off the back cover. Once the back cover is open, you can see the key compartment. The battery compartment is also secured by two clips. Pry them open one by one. Remove the battery cover, separate the chip and battery section, and then use the screwdriver to gently pry out the battery. The battery will then come out. Replace with a new battery, making sure not to reverse the positive and negative terminals. The flat side is the positive terminal, and the raised side is the negative terminal.
20
2
Share

How to Clean a Motorcycle Carburetor?

Remove the carburetor from the motorcycle, first clean the exterior of the carburetor, then disassemble and clean each major component. Main cleaning areas: the main jet, float chamber, float needle valve, etc. Thoroughly remove sediment and accumulated impurities inside the carburetor. Turn off the fuel, disconnect the fuel line. Use a 8mm or 10mm wrench (depending on the nut size) to unscrew the nuts connecting the carburetor to the engine. Then unscrew the screws connecting the carburetor to the air filter, and finally remove the throttle cable. Spray carburetor cleaner directly into each jet.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.