What does the yellow OFF light on the dashboard mean?

1 Answers
DelKate
07/29/25 12:59pm
Car dashboard yellow light OFF means closed, ON means open. The OFF light on the car mainly refers to ESP OFF. ESP stands for Electronic Stability Program, which is an active safety device mainly used to prevent the vehicle from skidding and fishtailing. If the ESP OFF light on the car dashboard lights up, it means that the vehicle's electronic stability control system is turned off or malfunctioning. If you accidentally press the ESP OFF button on the vehicle, you can turn the ESP back on by pressing it again briefly. If the ESP OFF light is on due to a system malfunction, you should send the vehicle to a 4S shop for repair in time. There are many reasons for the malfunction light to come on, such as circuit failure, sensor damage, electronic control unit signal error, battery power loss, etc. ESP is particularly sensitive to oversteer or understeer. For example, when the car turns left too sharply (oversteer) on a slippery road, it will fishtail to the right. The sensor will sense the skid and quickly brake the right front wheel to restore traction, generating an opposite torque to keep the car in the original lane. The difference between a car with ESP and one with only ABS and ASR is that ABS and ASR can only react passively, while ESP can detect and analyze the vehicle condition and correct driving errors, preventing problems before they occur.
Was this review help?
20
0
Share
More Forum Discussions

Is Replacing Valve Stem Seals Considered a Major Overhaul?

Replacing valve stem seals is not considered a major overhaul. However, if the engine cylinder head is disassembled to replace the valve stem seals, then it would be classified as a major overhaul. It is recommended that car owners use non-disassembly cylinder replacement technology to replace valve stem seals. Under any circumstances, try to avoid opening the engine cylinder head. The valve stem seals are located on the valves and are made of rubber material. After prolonged use, this component may experience reduced elasticity. Valve stem seals are typically composed of an outer frame and fluororubber vulcanized together, with a self-tightening spring or steel wire installed at the radial opening. They are used to seal the engine valve guide rods and are a type of oil seal. They prevent engine oil from entering the intake and exhaust pipes, which could lead to oil loss. Additionally, they prevent the leakage of the gasoline-air mixture and exhaust gases, as well as prevent engine oil from entering the combustion chamber.
20
2
Share

What are the Precautions for Buying and Transferring Used Cars?

Precautions for buying and transferring used cars include: 1. Annual inspection: Check the supplementary page of the vehicle license (driving license) to confirm whether the vehicle has undergone normal annual inspection. If it hasn't, the transfer procedure cannot be processed. 2. Exhaust emission certificate: Verify if there is an exhaust emission certificate. If not, not only will it need to be reissued during the next inspection, but there may also be fines, causing losses to the buyer. 3. Name change: After the vehicle is transferred, promptly update the insurance policy with the new owner's name. Otherwise, disputes with the insurance company may arise in case of an accident. 4. Sales contract: Sign a standardized sales contract during the transaction. Since there are many details to consider in used car transactions and transfers, and many aspects are easily overlooked, it is recommended that both parties sign a standardized sales contract issued by the industrial and commercial administration department to protect the legitimate rights and interests of both the buyer and the seller.
5
4
Share

What Causes the BMW 5 Series Horn Not to Work?

BMW 5 Series horn not working is likely due to a broken power circuit. You can check the circuit to see if it's clear or broken. Another possible cause is poor contact of the horn button. It is recommended that the owner go to a professional auto repair shop or 4S store for inspection. Here are the specific reasons: 1. Broken power circuit: The issue of a broken horn power circuit can be checked to see if the circuit is clear or broken. If so, just reconnect the circuit. 2. Poor contact: It may be due to poor contact of the horn button. Poor contact can also cause the horn not to work. You can check it and then repair the contact points. 3. Relay contact erosion: It may be due to relay contact erosion or excessive gap, as well as a broken magnetic coil of the horn. 4. Excessive armature air gap: It may be due to an excessive armature air gap of the horn. An excessive armature air gap can cause the horn not to work, but this can also be repaired by adjusting it properly.
5
1
Share

Will modifying the steering wheel affect the airbag?

Modifying the steering wheel will not affect the airbag. However, during removal, the steering wheel must be kept in the center position, and the clock spring must also be centered; otherwise, it may break, causing the airbag light to illuminate. The airbag control module is typically located in front of or beneath the gear shift lever. Areas marked with AIRBAG indicate the presence of an airbag. Use a diagnostic tool to scan the airbag system for faults and repair them accordingly. If no faults are detected, the diagnostic tool can directly clear any error codes. The airbag system is a passive safety protection system that, when used in conjunction with seat belts, provides effective collision protection for occupants. In the event of a collision, airbags can reduce head injuries by 25% and facial injuries by approximately 80%.
5
5
Share

What to Do When the Car Shows a Tire Pressure System Malfunction

Solutions for when the car shows a tire pressure system malfunction: First, get out of the car and check to confirm the tires are in normal condition with no signs of air leakage; Remove the key and reinsert it to restart the car; If the tire pressure monitoring still doesn't work, start the car and drive at low speed for about five to six minutes, and in most cases, the tire pressure will be displayed; Disconnect the car battery's negative terminal for a few minutes, then reconnect it, and after inserting the key and resetting the central control, the tire pressure should display normally; If the car has driven through water and the tires have taken in water, causing the tire pressure monitor's battery to short-circuit and fail to supply power normally, cleaning it thoroughly should resolve the issue; If the battery is dead, replacing it will solve the problem. Tire pressure reset method: First, turn on the ignition, press and hold the tire pressure monitoring reset button until you hear a "beep," then release it. The tire pressure monitoring system will store the current normal tire pressure data, automatically clear the previous data, and finally, the dashboard's warning light will turn off, completing the tire pressure reset.
13
3
Share

Is the Engine of the Lynk & Co 03 the Same as Volvo's?

The engine of the Lynk & Co 03 is the same as Volvo's. The engine model of the Lynk & Co 03 is JLH3G15TD, which is equipped with a 1.5T turbocharged engine and matched with a 6-speed manual transmission. This engine has a maximum power of 115kW, a maximum torque of 245Nm, a maximum power speed of 5000rpm, and a maximum torque speed range of 1450 to 4000rpm. It also features direct fuel injection technology and uses an aluminum alloy cylinder head and block. The Lynk & Co 03 has a body length, width, and height of 4639mm, 1840mm, and 1472mm respectively, with a wheelbase of 2730mm. The drive system is front-wheel drive, with a MacPherson independent suspension at the front and a multi-link independent suspension at the rear.
12
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.