What Does the Transmission Lever Mean?

What is the fuel grade for the BMW 3 Series?

The fuel grade for the BMW 3 Series is 95 octane. This grade of gasoline burns fully, is less prone to carbon deposits, and provides quick acceleration response. 95 octane gasoline consists of 95% isooctane and 3% n-heptane. High-compression engines should use high-octane gasoline; using low-octane gasoline in a high-compression engine can cause abnormal combustion, leading to knocking, increased fuel consumption, and reduced driving power. Taking the BMW 3 Series 320i as an example: in terms of body dimensions, its length, width, and height are 4719mm, 1827mm, and 1459mm respectively, with a wheelbase of 2851mm. In terms of power, the BMW 3 Series 320i is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 156 PS, a maximum power of 115 kW, and a maximum torque of 250 Nm.

7

5

Share

Can You Stop Directly in Fourth Gear with a Manual Transmission?

You can stop directly in fourth gear with a manual transmission by following these steps: 1. Press the brake pedal, slow down, then press the clutch while continuing to brake; 2. After stopping, shift to neutral, engage the handbrake, and release the clutch and brake to complete the stop. The correct method to start a manual transmission car is: 1. Fully depress the clutch with your left foot; 2. Shift the gear lever into first gear; 3. Turn on the left turn signal and honk the horn; 4. Release the handbrake and gently lift the clutch with your left foot; 5. Lightly press the accelerator with the ball of your right foot. Precautions for driving a manual transmission car include: 1. Shift gears frequently according to speed; 2. Avoid prolonged semi-clutch engagement; 3. Do not shift gears without fully disengaging the clutch; 4. Do not drive with the handbrake engaged; 5. Exercise caution when driving over bumps or potholes.

8

4

Share

Where is the fuel tank cap button for the BYD Song?

The fuel tank cap switch for the BYD Song is located at the lower left side of the driver's compartment. There is a pull cover marked with a fuel pump symbol; lifting this cover will open the fuel cap. Additional information about automotive fuel tanks is as follows: 1. The automotive fuel tank is the full name of the car's fuel container. 2. Automotive fuel tanks are categorized by material: iron tanks and aluminum alloy tanks. With the development of various new materials, the rust prevention issue of iron fuel tanks has become the most significant quality concern, especially in today's environmentally conscious era. 3. For heavy-duty trucks: During the promotion of National IV and V vehicles, the quality of fuel in China has become a critical issue affecting the advancement of new models, with the quality of the fuel tank being a key focus. 4. Aluminum alloy fuel tanks not only meet strength requirements but also offer significant advantages in corrosion resistance compared to iron and other new materials, making them the preferred choice for large buses and heavy-duty trucks that consume large amounts of fuel and require high fuel quality. Automotive fuel tanks are also categorized by function into standard tanks and heated tanks.

20

3

Share

Does the Bentley Bentayga PHEV comply with China VI emission standards?

Bentley Bentayga PHEV complies with China VI emission standards. China VI refers to the strict control of pollutant emission limits. Under the exclusion of working conditions and test influences, the carbon monoxide emissions of gasoline vehicles are reduced by 50%, the total hydrocarbon and non-methane hydrocarbon emission limits are reduced by 50%, and the nitrogen oxide emission limits are tightened by 42%. The Bentley Bentayga PHEV is a mid-to-large luxury SUV under the Bentley brand, equipped with a 3.0-liter V6 turbocharged engine, delivering a maximum power of 250 kW and a maximum torque of 450 Nm. The matched electric motor has a maximum power of 94 kW and a maximum torque of 350 Nm, paired with an 8-speed automatic transmission. In terms of suspension, the Bentley Bentayga PHEV uses a double-wishbone independent suspension at the front and a multi-link independent suspension at the rear.

17

3

Share

What are the components of a lubrication system?

Lubrication system consists of three major components: oil supply device, filtration device, and instrumentation & signaling device. Oil supply device: Includes oil pump, oil passages, oil pipes, pressure relief valve, etc., which enables oil to circulate in the system at a certain pressure and flow rate. Filtration device: Comprises oil strainer, coarse filter, fine filter, bypass valve (clogging indicator), capable of removing various impurities from the oil. Instrumentation & signaling device: Includes clogging indicator, pressure sensor, oil pressure alarm, warning light and pressure gauge, etc., allowing the driver to monitor the working status of the lubrication system at any time. Working principle of lubrication system: The main oil pump draws lubricating oil from the engine oil pan, then flows the oil into the oil cooler. The cooled oil passes through the oil filter and enters the main oil pipe at the lower part of the engine block, reaching various lubrication points under pressure. Function of lubrication system: During engine operation, it continuously delivers sufficient quantity of clean oil at appropriate temperature to all transmission component friction surfaces, forming an oil film between surfaces to achieve liquid friction. This reduces frictional resistance, lowers power consumption, decreases component wear, thereby improving engine reliability and durability.

19

0

Share

What is the fuel consumption of the Mercedes-Benz S-Class?

The Ministry of Industry and Information Technology (MIIT) has announced that the comprehensive fuel consumption of the Mercedes-Benz S-Class ranges between 7 to 9.2 liters per 100 kilometers. Below are the relevant details: There are two main factors that affect fuel consumption: 1. Engine displacement: The Mercedes-Benz S-Class is equipped with either a 2.0T or a 3.0 engine. Engine displacement is a direct factor influencing a car's fuel consumption. Generally, the larger the engine displacement, the higher the fuel consumption. 2. Drive configuration: Cars can have either two-wheel drive (2WD) or four-wheel drive (4WD), and engines can be front-mounted or rear-mounted. These differences also impact fuel consumption. For models with the same displacement, 4WD versions will always consume more fuel than 2WD versions. About Mercedes-Benz: The currently available Mercedes-Benz S-Class models include the 2018 and 2019 versions, launched in August 2018 and September 2019, respectively, and are available in both China V and China VI emission standards. Based on body structure, they can be divided into sedan and hardtop coupe versions. The 4WD versions feature a front-engine, four-wheel-drive configuration with full-time 4WD and a multi-plate clutch central differential. The dimensions of the current Mercedes-Benz S-Class models are 5259mm in length, 1899mm in width, and 1497mm in height, with a wheelbase of 3165mm.

15

4

Share

What Does the Transmission Lever Mean?

What is the fuel grade for the BMW 3 Series?

Can You Stop Directly in Fourth Gear with a Manual Transmission?

Where is the fuel tank cap button for the BYD Song?

Does the Bentley Bentayga PHEV comply with China VI emission standards?

What are the components of a lubrication system?

What is the fuel consumption of the Mercedes-Benz S-Class?

What Causes a Sudden Loss of Power in a Car Battery?

What car is blsuauto?

Why are the tail lights of Ford Focus on?

Where Does the Car Air Conditioner Drain Water From?