What does the supercharger HX50W mean?

1 Answers
LeDaisy
07/29/25 10:16pm
The "H" in the supercharger HX50W stands for HOLSET, "X" represents Wuxi, "50" indicates the size of the supercharger, and "W" denotes the bypass valve of the supercharger. The function of the supercharger: A supercharger, also known as an engine intake supercharger, compresses the air before it enters the engine cylinders to increase air density, allowing more air to fill the cylinders and thereby enhancing engine power. Engines equipped with superchargers not only deliver greater power output but also improve the altitude performance of the engine. The principle of the supercharger: It utilizes the high-temperature exhaust gas (700-900°C) discharged from the engine to drive the turbine in the turbocharger to rotate. The turbine shaft then drives the impeller in the compressor to rotate at high speed, compressing the air centrifugally and increasing the intake air density of the engine to 2-3 atmospheres. This allows more fuel to be injected into the engine, achieving the effect of improving the engine's specific power.
Was this review help?
7
0
Share
More Forum Discussions

What are the causes of Nissan Teana stepper motor failure?

Nissan Teana stepper motor failure may be caused by insufficient voltage, incorrect or loose connection of automotive shielding wires, or damage to the driver. In terms of appearance: The Teana features a full LED headlight assembly with a slender design, incorporating the iconic boomerang pattern inside the headlights. The continuous waistline extends from the headlight assembly all the way to the taillight assembly, giving the car body an exceptionally elongated appearance. In terms of power: The new Teana continues to offer a 2.0-liter naturally aspirated engine and a 2.0-liter turbocharged engine, both utilizing the same VC-Turbo technology as the Infiniti QX50. The maximum power outputs are 156 horsepower and 243 horsepower, with maximum torques of 197 Nm and 371 Nm, respectively.
12
5
Share

What is the resistance value of the Mercedes-Benz Sprinter fuel level sender?

The resistance value of the Mercedes-Benz Sprinter fuel level sender is around 100 ohms. Introduction to the car fuel level sender: The float in the fuel tank is a fuel level sensor, which is a sensing device for the fuel level. The fuel level sender and the fuel gauge together form the car's fuel level detection system. Composition of the fuel level sender: The car's fuel tank has a float connected by a thin metal rod. The float is usually made of foam plastic, and the end of the metal rod is attached to a variable resistor. A resistor is a device used to impede the flow of electric current. The greater the resistance, the smaller the current that passes through. In the fuel tank, the variable resistor consists of a piece of resistive material with one end grounded. A wiper arm connected to the fuel gauge slides along the resistive material, thereby conducting current from the fuel gauge to the resistor.
18
5
Share

What is the emission standard of the Envision?

The emission standard of the Envision is China 6. Appearance: The Envision has a length of 4686 mm, a width of 1839 mm, and a height of 1691 mm, with a wheelbase of 2750 mm. Power: The Envision is equipped with two engines: a 1.5-liter turbocharged engine and a 2.0-liter turbocharged engine. Configuration: The Envision uses a MacPherson independent suspension for the front and a multi-link independent suspension for the rear. The multi-link suspension enhances the vehicle's handling and ride comfort. It is an improved version of the double-wishbone suspension, where the two wishbones are replaced with separate links.
6
1
Share

What is the ground clearance of the GAC Trumpchi M8 chassis?

The ground clearance of the GAC Trumpchi M8 chassis is approximately 200 millimeters. Introduction to vehicle minimum ground clearance: Vehicle minimum ground clearance, also known as chassis height, is defined as the distance from the lowest point of the car's chassis to the ground when the vehicle is fully loaded. The ground clearance data reflects the vehicle's ability to pass through complex terrains. In previous standards, there were certain regulations for minimum ground clearance, usually between 150 and 160 millimeters, but this standard has now been abolished. Impact of minimum ground clearance: The minimum ground clearance of ordinary cars is generally within the range of 11-15 centimeters. For this parameter, the greater the ground clearance (generally referring to more than 13 centimeters), the better the passing performance of the car, but the worse the high-speed stability; the smaller the ground clearance (less than 110 millimeters), the better the high-speed stability, but the worse the passing performance. Nowadays, there is an automatic adjustment function for ground clearance, which is only available in cars equipped with air suspension, and can well meet the needs of different road surfaces.
12
5
Share

Where is the motor relay for the Mercedes-Benz C200 located?

The motor relay for the Mercedes-Benz C200 is located in the control cabinet or control box. Exterior of the Mercedes-Benz C200: The front face of the Mercedes-Benz C200 is stylish and fashionable, with the headlights incorporating warm-toned light sources, creating a very elegant visual effect. Performance of the Mercedes-Benz C200: The Mercedes-Benz C200 is a front-engine, all-wheel-drive version, equipped with the M274 920 four-cylinder 2.0 direct-injection turbocharged engine, with a maximum power output of 184 kW and a maximum torque of 300 Nm. It can sustain maximum torque output from 1200 rpm up to 4000 rpm. It is paired with a 7-speed AT automatic transmission.
7
2
Share

Will flashing S4 software on an Audi A4L affect the warranty?

Flashing S4 software on an Audi A4L will not affect the warranty. Maintenance cycle: Authorized dealerships determine the vehicle maintenance cycle based on local driving conditions. For certain components, the maintenance cycle may differ from the intervals recommended in the official manual. Maintenance precautions: If the local environment is harsh or road conditions are poor, the maintenance cycle should be appropriately shortened, especially for the air filter element and cabin air filter element. Additionally, ensure the correct specifications and high-quality fluids are used. The replacement of brake pads, wiper blades, batteries, tires, etc., depends on wear and tear, so regular inspections are essential. Maintenance items: Primarily include engine oil and oil filter replacement, cabin air filter replacement as needed, battery inspection, brake pedal and parking brake check, brake pads and brake disc inspection, brake fluid and clutch fluid check, tire and tire pressure inspection, and inspection of lights, horn, wipers, and washer jets.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.