···
Log in / Register

What does the 'Study to Reduce Points' feature in Traffic Management 12123 mean?

1 Answers
MacLiam
09/03/25 6:14am
There are two possibilities for the 'Study to Reduce Points' feature in Traffic Management 12123. Here are the specific introductions for these two: 1. Passing the exam: Motor vehicle drivers participate in road traffic safety laws, regulations, and related knowledge learning organized by the traffic management department of the public security organ and pass the exam. 2. Participating in activities: Participating in traffic safety public welfare activities at the place where the motor vehicle driving license was issued and meeting the relevant requirements can apply for a reduction in traffic violation points. 'Study to Reduce Points' is a convenient traffic management measure uniformly deployed by the Traffic Management Bureau of the Ministry of Public Security. Starting from March 1, Chongqing took the lead in piloting the implementation nationwide. After the measure is introduced, it will be promoted for a long time. Drivers can reasonably arrange time to participate in 'Study to Reduce Points' according to their current point situation, avoiding a large number of people applying for online learning at the same time, which may cause network system lag and affect the learning experience.
Was this review help?
18
0
Share
More Forum Discussions

Direction of the Connecting Rod Bearing Notch?

The direction of the connecting rod bearing notch is actually towards the oil pump, primarily serving to lubricate the engine connecting rod. The connecting rod bearing is divided into two parts: the upper bearing and the lower bearing, installed at the connection point between the connecting rod and the crankshaft, thus providing wear resistance, support, and transmission functions. More details about the connecting rod bearing are as follows: 1. Detail one: The inner cylindrical surface of the upper connecting rod bearing is circumferentially equipped with an oil groove of reasonable arc length, and the bearing wall at the oil groove section is provided with an oil passage hole, which is the notch mentioned in this article. Additionally, assembly can be guided by the position of the locating lip. Bearings without a locating lip can be used on connecting rods with a locating lip, but the reverse is not possible. 2. Detail two: When assembling the connecting rod bearing, do not reverse the direction, as this can cause varying degrees of impact. Furthermore, the screws must reach the corresponding torque, but avoid over-tightening, as this can lead to excessive stress on the bolts, not only causing internal thread stripping but also potentially deforming the bolts.
18
4
Share

Does Kunlun Star Gasoline Compound Additive Harm the Car?

Kunlun Star Gasoline Compound Additive does not harm the car. Kunlun Star Gasoline Compound Additive is a cleaning-type detergent, also known as Kunlun Fuel Additive/Fuel System Cleaner. Its main component is high-molecular surface-active substances, and as long as it is a genuine high-quality product, it works very well. The functions of Kunlun Star Gasoline Compound Additive are as follows: 1. Function One: Improve combustion efficiency and reduce fuel consumption. The gasoline compound additive can generate tiny nano-clusters during combustion, which detonate before or during combustion, producing steam with a cleaning effect. It helps decompose and break down deposits in the combustion chamber, controls carbon buildup, reduces vehicle exhaust emissions, keeps the engine in optimal condition, makes the combustion chamber cleaner, and ensures more complete combustion, thereby improving fuel economy. 2. Function Two: Rust removal and prevention. The gasoline compound additive can form a protective film on the fuel system and engine cylinder surfaces, providing protection to reduce corrosion and damage caused by low-quality gasoline to the engine and fuel system, extending the engine's service life.
3
2
Share

Do I need to press the brake after pulling the handbrake and shifting to P gear?

After pulling the handbrake and shifting to P gear, you do not need to press the brake. You only need to pull the handbrake. When parking, you still need to pull the handbrake after shifting to P gear. The P gear is just a parking gear and does not function as a handbrake. When the gear shift lever is in this position, the parking lock mechanism locks the transmission output shaft. The relevant introduction about the handbrake is as follows: 1. Introduction one: The professional term for the handbrake is auxiliary brake. Its principle is different from that of the brake. It uses a steel wire cable connected to the rear brake shoe to brake the car. 2. Introduction two: Long-term use of the handbrake will cause plastic deformation of the steel wire. Since this deformation is irreversible, long-term use will reduce its effectiveness, and the travel of the handbrake will also increase. There is also a return spring used in conjunction with the handbrake. 3. Introduction three: When the handbrake is pulled for braking, the spring is stretched. When the handbrake is released, the spring returns to its original length. Long-term use of the handbrake will also cause corresponding deformation of the spring.
4
2
Share

Should You Press the Button When Pulling Up the Handbrake?

When pulling up the handbrake, it is generally not necessary to press the handbrake button. Pressing it reduces gear friction slightly and avoids the sound of gear scraping. For durability, it is advisable to press the button while pulling, though pulling without pressing is also possible since the handbrake gear is unidirectional, albeit with some noise. Here are some related details about the handbrake: 1. Detail One: The primary function of the handbrake is to control the speed of the rear wheels, but its braking effect is minimal at high speeds. 2. Detail Two: If the driver pulls the handbrake while driving at high speed, it can easily cause the rear wheels to lock up, the cable to snap, leading to side skidding or even rollover. 3. Detail Three: Additionally, during sharp turns or driving in rainy, snowy, or icy conditions, avoid abruptly using the handbrake, as this can cause the ABS system to fail, with the rear wheels losing all rotation signals, increasing the risk of veering or fishtailing.
19
4
Share

What does a bored engine mean?

A bored engine refers to increasing the diameter of the engine cylinders proportionally to create larger cylinders than the original ones, thereby increasing the combustion volume. This process enhances displacement and boosts power. However, bored engines are generally not recommended as they tend to accelerate wear. Here are some details about car engines: 1. Introduction one: The car engine is the machine that provides power to the car, acting as the heart of the vehicle. It affects the car's power, fuel efficiency, and environmental performance. Depending on the power source, car engines can be categorized into diesel engines, gasoline engines, electric motors for electric vehicles, and hybrid systems, among others. 2. Introduction two: Common gasoline and diesel engines are both types of reciprocating piston internal combustion engines, which convert the chemical energy of fuel into the mechanical energy of piston movement to output power. Gasoline engines have higher rotational speeds, are lighter, produce less noise, are easier to start, and have lower manufacturing costs. Diesel engines, on the other hand, have higher compression ratios, greater thermal efficiency, and better fuel economy and emission performance compared to gasoline engines.
19
1
Share

Is Rallye Power Engine Oil a Big Brand?

Rallye Power Engine Oil is a premium high-end brand under Yumin. The product quality of Rallye Power Engine Oil is reliable and stable, with aesthetically pleasing designs, environmentally friendly and energy-saving materials, and a high market share. It is well-loved by a wide range of customers, making Rallye Power Engine Oil an excellent choice. Introduction 1: Engine oil, also known as engine lubricant, is hailed as the "blood" of a car. It serves to lubricate, clean, cool, seal, reduce friction, prevent rust, and protect against corrosion in the engine. Introduction 2: The engine is the heart of a car. Inside the engine, there are many metal surfaces that move against each other in friction. These components operate at high speeds and in harsh environments, with working temperatures reaching 400 to 600 degrees Celsius. Under such extreme conditions, only qualified lubricating oil can reduce wear on engine parts and extend their service life.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.