What does the inverted triangle yield sign mean?

1 Answers
VonPenelope
07/30/25 8:31am
It indicates that vehicles should slow down and yield. Below are the specific meanings of the inverted triangle: 1. An inverted triangle with the word "Yield" inside is a yield sign, indicating that vehicles must slow down or stop to observe traffic conditions on the main road. Proceed only when it is safe and after ensuring priority for vehicles on the main road. It is usually placed at intersections of minor roads with good visibility. 2. From the driver's perspective, it appears as an inverted triangle, often accompanied by two parallel dashed lines ahead. This sign typically appears at small intersections without traffic signals but with pedestrian crossings, or on auxiliary roads near main road exits. Drivers should exercise caution, observe carefully, and yield to pedestrians crossing the road. Vehicles on auxiliary roads must yield to vehicles exiting the main road. In case of rear-end collisions or scrapes at such locations, the party required to yield will bear full responsibility.
Was this review help?
15
0
Share
More Forum Discussions

How long does it take to study for the driving license subject 2 test?

It takes about 10 to 15 days to study for the driving license subject test, including 2 hours of theoretical learning and 22 hours of practical learning. Precautions for the subject 2 test: 1. During the preparation before getting into the car, adjust the seat and fasten the seat belt before fingerprint verification, and wait for the instructions of the accompanying coach before operating; 2. Each test item in the test site is detected by GPS positioning, and the control line of each item represents the test area of the item. When the front of the vehicle passes the control line, it means the test starts; 3. Before entering the next test item each time, confirm whether there are still vehicles taking the test ahead. If there are vehicles taking the test in the front item, you must stop and wait before the yellow line of the item and must not enter. Entering rashly will result in test failure.
13
0
Share

How Many Chances Are There for Each Subject in the Driving Test?

There are 5 exam attempts for each subject in the driving test. Each subject exam includes one initial attempt and one retake. After completing the subject one exam, you must pass subjects two and three within three years. If you fail to do so, all previous exam results will be invalidated, and you will need to re-register for the subject one exam. Under the new regulations, both subjects two and three offer 5 attempts each. If you cannot pass within these 5 attempts, you must retake the subject one exam. Below is an introduction to the driving test subjects: 1. Traffic regulations and related knowledge (Subject One): The full score is 100, with 90 or above considered passing (including 90). 2. Field driving (Subject Two): Results are either pass or fail. It includes 9 mandatory test items (all without poles): reverse parking, narrow road U-turn, parallel parking, hill start, right-angle turn, curve driving, emergency braking, tunnel, and toll booth card collection. 3. Road driving (Subject Three): Conducted on actual roads or simulated environments with real vehicles. The exam is fully monitored by electronic eyes and proctored by traffic police. 4. Safe and civilized driving theory test (Subject Four): Unlike Subject One, it includes image analysis and judgment. The test consists of 50 questions, each worth 2 points. The full score is 100, with 90 or above required to pass.
15
2
Share

What are the reasons for no signal in the reverse camera when shifting to reverse gear?

The reasons for no signal in the reverse camera when shifting to reverse gear are: 1. Damage to the reverse camera probe; 2. Faulty signal wiring of the camera; 3. Malfunction of the gear position sensor. Tips for using the reverse camera include: 1. Before reversing, check the situation behind the vehicle, plan the reversing route, and avoid accelerating while reversing to control the speed; 2. Do not focus solely on the rear while reversing; observe the left and right rearview mirrors after ensuring rear safety. The reverse camera, also known as the parking assist system, reverse visual system, or onboard monitoring system, is widely used in various large, medium, and small vehicles for reversing or driving safety assistance.
4
4
Share

What is the function of a circuit breaker?

The function of a circuit breaker is to use the control of a cam to disconnect or close its contacts at specified times and points within a set period, thereby connecting and cutting off the low-voltage current in the ignition coil. This causes the secondary coil to induce a high voltage, which is then transmitted through the high-voltage line to the center electrode of the spark plug, generating a high-voltage spark to ignite the combustible mixture in the engine. The circuit breaker is a crucial component of the battery ignition system. The opening and closing of the circuit breaker contacts cut off or connect the primary circuit of the ignition coil, inducing a high voltage in the secondary coil due to electromagnetic induction. The circuit breaker periodically opens and closes the primary circuit of the ignition coil and is generally composed of contact points and a breaker cam. The contact pair of the circuit breaker is made of tungsten alloy, with one contact being fixed and the other being movable.
5
3
Share

What causes abnormal noise when starting the engine?

Possible causes of abnormal engine noise include: 1. Engine knocking: The "clanking" sound occurs when the piston skirt impacts the cylinder wall during operation, requiring replacement of the engine's four matching components; 2. Intake/exhaust system noise: Intake manifold leaks produce sounds during idle that intensify with RPM increase; 3. A "hissing" noise indicates cooling system issues causing engine overheating; 4. A "squeaking" noise suggests engine belt slippage; 5. A "clicking" noise results from engine carbon deposits.
18
5
Share

How to Reset the Maintenance Wrench Light on Hanteng X5?

Method to reset the maintenance wrench light on Hanteng X5: Insert the key into the ignition switch, press and hold the small black rod on the instrument panel, power on the car, then release the small rod on the instrument panel. The small wrench warning light is set by the manufacturer to remind the owner to perform maintenance at specified intervals. After completing the car maintenance, it is necessary to follow the procedure to reset the maintenance reminder light to turn it off. The Hanteng X5 is a compact SUV with body dimensions of 4501mm in length, 1820mm in width, and 1648mm in height, with a wheelbase of 2600mm. The Hanteng X5 is equipped with a 1.5-liter turbocharged engine across all models, paired with either a 5-speed manual transmission or a 6-speed automatic transmission.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.