What does the GAC Trumpchi logo mean?

How to Determine the Tire Date?

On one side of the tire, there is usually a molded DOT mark. The last four digits of this mark provide information about the production date, consisting of four digits "AABB". The first two digits "AA" indicate the week of the year, while the last two digits "BB" represent the year. Here are the specific steps to determine the tire date: 1. First, locate the U.S. Department of Transportation (DOT) number on the tire sidewall. This number starts with "DOT" and is 10-12 digits long. If the number is not visible, it might be engraved on the inner side. Without connecting to a vehicle, you can simply turn the tire to see the number. Even if the tire is already mounted on the car, you can check the inner side with a flashlight. 2. Now, look at the last two digits of the DOT number. If possible, it's best to write them down. These digits indicate the production year of the tire. If the last digits are "21", it means the tire was produced in 2021. 3. Next, look at the two digits before the last two digits. These digits represent the production week. If the digits are "09", it means the tire was produced in the 9th week of that year.

3

2

Share

Can a Hairdryer Be Used Instead of a Heat Gun for Film Application?

It is not advisable to use a hairdryer if a heat gun is not available for film application. A household hairdryer is unlikely to work because it cannot reach the required temperature, and its heat output is inconsistent. This is especially true for the front and rear windshields, which have significant curvature. It is recommended to have the film applied professionally at a shop. Below is a supplementary introduction to the film application method: 1. Glass and Vehicle Cleaning: Before applying the film, the car should be parked in a relatively sealed, dust-free environment for cleaning. The glass must be thoroughly cleaned with cleaning powder, ensuring no stubborn stains are left, as debris can affect the film's adhesion. 2. Cutting the Film to Size: Cut the film to match the size of the glass. You can spray some water on the glass surface and then adhere a plastic film of a certain thickness to the window. Trace the edges to create a template, ensuring the template is slightly larger than the glass. 3. Heat Shaping the Film: Also known as thermal shaping, this step ensures the film fits the glass more precisely. Poor execution can lead to bubbles and an unattractive finish. 4. Trimming and Scraping the Film: Trimming is the most delicate part of the entire process. After the film is heat-shaped, use a utility knife to carefully trim excess material along the glass edges. The pressure applied is crucial—too much force may scratch the glass, while too little may not cut through the film.

12

4

Share

How to Deal with a Leaking Car Water Pump?

Car water pump leaks are generally caused by damaged seals inside, and it is recommended to replace the water pump with a new one. If the water pump leaks, it will cause a reduction in coolant, leading to an increase in engine temperature; a faulty water pump that does not circulate will result in excessive radiator temperature, non-circulating cooling water, and ineffective cooling fans. Below is relevant information about car water pumps: 1. If the water pump leaks, it will cause a reduction in coolant, leading to an increase in engine temperature; a faulty water pump that does not circulate will result in excessive radiator temperature, non-circulating cooling water, and ineffective cooling fans. In severe cases, the cooling water may evaporate immediately, causing the engine temperature to rise excessively. At this point, pressing the accelerator will feel weak, and the engine may overheat. 2. If the water pump is not functioning properly, the coolant cannot circulate within the engine for heat exchange, and the engine heat cannot be dissipated, which will also cause the engine temperature to rise. If the water pump is damaged and not working, it can cause the engine to overheat (i.e., boiling water). If not addressed promptly, it can lead to engine seizure. Excessive engine temperature will reduce the lubricating ability of the engine oil, leading to increased wear of engine components. If the temperature rises to a certain level, it can cause severe failures such as cylinder scoring or bearing seizure, ultimately resulting in engine failure and scrapping.

13

5

Share

Is It Necessary to Rotate Front and Rear Tires for Small Cars?

Tire rotation between front and rear positions is necessary as the front and rear tires wear differently, so it's important to regularly swap their positions. Generally, for front-wheel-drive vehicles, the front tires bear the majority of forces during load-bearing, acceleration, steering, and braking, leading to faster wear compared to the rear tires, with a wear ratio that can reach 2:1. Below are additional methods to extend tire lifespan: 1. Regularly check tire pressure: Inflate under-inflated tires promptly and maintain consistent pressure across all tires. Otherwise, tires with lower pressure will wear out faster, increase driving resistance, and raise fuel consumption. 2. Avoid hitting obstacles: At high speeds, impacts with potholes or other obstacles can cause severe deformation between the obstacle and the wheel rim flange, potentially breaking the tire's inner cord layers and leading to bulges where air escapes. 3. Perform regular four-wheel alignment checks and dynamic balance tests: Research shows that incorrect four-wheel alignment (e.g., camber, caster, toe) can cause uneven tire wear, significantly reducing tire lifespan. 4. Frequently remove stones or debris from tread grooves to prevent tire crown deformation: Inspect the tire sidewalls for cuts or punctures that expose the cords, and replace the tire if necessary.

11

0

Share

What Causes the Car to Always Overheat?

The reasons for frequent high-temperature alarms in a car are as follows: 1. Circuit failure causing the electronic cooling fan to stop working, reducing the radiator's heat dissipation capacity. 2. Check the operation of the electric fan. Unplug the electric fan's wiring harness and power it directly with a power line. 3. If the electric fan rotates, it indicates proper functioning; if not, it suggests damage, requiring inspection of the relay and its circuit. 4. If the fan rotates with intact and powered wiring, it indicates a damaged or failed relay. 5. If all the above checks are normal, it suggests a damaged temperature sensor or its probe. The hazards of high-temperature environments to cars are as follows: 1. When the car is running, high external temperatures slow down tire heat dissipation, making them prone to overheating and excessive pressure, leading to tire blowouts. The faster the speed, the more heat the tires generate, increasing the likelihood of blowouts. 2. The braking efficiency of the car decreases as the temperature rises. For hydraulically braked cars, brake fluid may experience vapor lock at high temperatures. 3. Under frequent braking conditions, brake fluid temperature can exceed 100°C, easily causing the rubber cup to expand and brake fluid vapor lock, leading to reduced braking efficiency and compromised driving safety.

10

0

Share

How to ventilate in the car on rainy days?

Close the windows and turn on the air conditioning's external circulation. On rainy days, if the temperature is moderate and you just want ventilation, simply turn on the fan for ventilation without pressing the air conditioning button. If it's stuffy and hot, you can press the air conditioning button. Note that it is recommended not to sleep or rest in the car. Here are additional notes on precautions for resting in the car: 1. Open the window for ventilation: Leaving a small gap can also facilitate air circulation. Whether it's a hot summer or a cold winter, this gap might be a lifesaver. 2. Turn on the car's external circulation mode: Many car owners are accustomed to using the internal circulation mode for air conditioning, which is not wrong. However, during rest, it is recommended to switch to the external circulation mode. 3. Regularly check for exhaust pipe leaks and whether the windows are sealed: If carbon monoxide from the vehicle's exhaust leaks into the car, it can gradually accumulate and increase in concentration, leading to poisoning. If the exhaust pipe is damaged, exhaust gases can more easily enter the car, increasing the risk. The same consideration applies to keeping windows closed. 4. Try to park the vehicle in an open outdoor area: Confined spaces are more likely to cause carbon monoxide buildup, and some underground parking garages inherently have poor air circulation. When resting, the vehicle should be parked in an open outdoor area to ensure fresh air circulation.

17

5

Share

What does the GAC Trumpchi logo mean?

How to Determine the Tire Date?

Can a Hairdryer Be Used Instead of a Heat Gun for Film Application?

How to Deal with a Leaking Car Water Pump?

Is It Necessary to Rotate Front and Rear Tires for Small Cars?

What Causes the Car to Always Overheat?

How to ventilate in the car on rainy days?

How to Test for Steering Pull?

Can 12580 vehicle moving service check out-of-town license plates?

What car is the SWM logo?

What is the actual fuel consumption of the Passat 330?