What does the exclamation mark in the triangle on the dashboard mean?

How to Cancel the Maintenance Warning Light?

To cancel the maintenance reminder, follow these steps: Open the "Settings" on the dashboard, then select "Vehicle Settings", followed by "Maintenance Mileage", and finally choose "Clear". Below are the detailed items for car maintenance: 1. Replacement: Replace engine oil and oil filter. 2. Inspection and Refill: Check and refill the auxiliary tank water level, check and refill the windshield washer tank, check and refill the tire pressure for all four wheels. 3. Cleaning: Perform an engine cleaning. Here is extended information about car maintenance intervals and main contents: 1. 5000 km: After driving 5000 km, replace the engine oil and oil filter. 2. 10000 km: After driving 10000 km, replace the engine oil, oil filter, air filter, and fuel filter. 3. 15000 km: After driving 15000 km, replace the engine oil, oil filter, and cabin air filter. 4. 20000 km: After driving 20000 km, replace the engine oil, oil filter, air filter, and fuel filter. 5. 25000 km: After driving 25000 km, replace the engine oil and oil filter.

12

4

Share

What Causes the Car to Pull to One Side When Braking?

Reasons for the car pulling to one side when braking: The braking force on the left and right sides is uneven. If this occurs, it is necessary to have it adjusted at a professional facility. The car's braking system is crucial as it affects the vehicle's driving safety and stability. The braking system mainly consists of a vacuum booster pump, master brake cylinder, brake caliper, brake pads, and brake discs. Below are the maintenance methods for the braking system: 1. Use professional brake disc cleaner: Before use, shake the liquid in the can thoroughly. Spray directly onto the area to be cleaned until dust and oil stains are completely removed. Wipe clean with a clean towel, leaving no dust or residue. 2. Use professional brake caliper slide pin lubricant: Wear a single-finger glove and apply the product evenly on the surface of the brake caliper slide pin and inside the slide pin groove. Do not mix with other mineral-based lubricating oils. 3. Use professional high-temperature resistant brake pad protector: Wear a single-finger glove and apply the product evenly on the back of the brake pads and inside the sliding grooves at both ends of the brake pads. 4. Use professional high-temperature anti-seize lubricant: Wear a single-finger glove and apply the product evenly on each tire bolt and the metal contact surfaces between the wheel rim and hub.

7

0

Share

How many days after painting can you wash the car?

In good weather, one week is sufficient; in cloudy weather, 15 days are recommended. Below is expanded information on precautions during the painting process: 1. Gun Adjustment: Before spraying, the spray gun and related equipment should be clean and in proper working condition. Check whether the spray gun produces the ideal spray pattern. An ideal spray pattern should be symmetrical, with evenly distributed atomized particles, clear edges, and only a minimal amount of overspray beyond the edges. Lower atomization pressure helps achieve the correct, uniform spray pattern, reducing bounce-back and overspray. 2. Holding the Gun: The correct spraying path should remain perpendicular to the workpiece surface. Depending on the angle of the surface being painted, the distance between the spray gun and the surface is generally 15~30 cm. To obtain a wetter, darker, and thicker coating, the distance can be closer; for a drier, lighter, and thinner coating, the distance can be farther. 3. Gun Movement: Gun movement includes the angle of the spray gun relative to the surface and the speed of the spray gun. The spray gun should be kept at a right angle to the surface and moved parallel. The movement speed of the spray gun is typically adjusted between 30~60 cm/s and should remain constant. If the spray gun is tilted and moved in an arc or at variable speeds, it will result in uneven paint thickness and may cause streaks and spots.

12

4

Share

Should You Engage the Handbrake First or Shift to P First When Parking an Automatic Transmission Car?

For automatic transmissions, shift to P first and then engage the handbrake. Here is some relevant information about automatic transmissions: 1. Transmission Types: There are primarily two types of automatic transmissions used in cars. One is the stepped automatic transmission, and the other is the continuously variable transmission (CVT). The most commonly used in passenger cars is the mechanical CVT, which utilizes a V-shaped metal belt or chain to transmit torque between the driving and driven pulleys in their V-shaped grooves. This type of transmission is typically used in smaller vehicles. 2. Operational Characteristics: When driving a modern automatic transmission car, the driver only needs to control the accelerator pedal. The computer analyzes signals from sensors that detect the engine throttle opening and vehicle speed, automatically controlling the transmission or shifting it into different gears. Generally, automatic transmissions result in some power loss from the engine. The biggest advantage of automatic transmission vehicles is convenience, especially in traffic jams. The benefits are even more pronounced when stuck in traffic on a steep incline. Automatic transmission cars are becoming increasingly popular. From the perspective of advanced automotive development countries, most vehicles are transitioning to fully automatic transmissions. The trend in automotive development is for automatic transmissions to replace manual transmissions as the primary choice for daily driving.

16

2

Share

Is It Normal for Car Headlights to Get Hot?

Car headlights getting hot is normal. When the headlights are turned on, the current passing through the filament generates a significant amount of heat, which is why the headlights become hot. Below is an introduction to car headlights: Reasons for car headlights getting hot: When the headlights are turned on, the current passing through the filament generates a large amount of heat, causing the filament to reach a high temperature and emit light. The light emitted by the filament contains infrared components, most of which pass through the bulb's glass and radiate into the surrounding environment, while a small portion is absorbed by the glass. When you touch the headlight cover glass, it will feel very hot. If the headlight is damaged, it is usually replaced with a similar type. Some cars are equipped with High-Intensity Discharge (HID) headlights, which generate high-density light through a high-voltage arc discharge produced by a pre-designed electronic system. Check the headlight lens for cracks. Although surface cracks do not affect the headlight's illumination performance, moisture can seep into the headlight along the cracks, reducing the bulb's lifespan. Introduction to headlight maintenance: If moisture enters the headlight, it will reduce the bulb's lifespan. Therefore, it is important to check the headlight's sealing. If the sealing ring between the lens and the reflector is damaged, replace it promptly. For semi-sealed headlights, if the reflector turns black or the light intensity decreases, it should be replaced.

14

4

Share

What Causes Car Windows to Fail to Open?

Car windows may fail to open due to damaged window lift motors or poor contact in the electrical control wiring harness. Below is relevant information about car windows: Reasons for car window lift failure: To protect the power supply circuit, most window lift motors are equipped with an overheating protection mechanism. If components overheat for any reason, the motor will enter a protection state, causing the window to stop functioning. The door window guide channel is an often-overlooked detail. Over time, dust can accumulate in the guide channel, increasing resistance and potentially making it difficult for the window to rise. Solutions for car window lift failure: Clean the window lift channel by inserting a chopstick wrapped in a towel into the guide channel. Adjust the number of towel layers based on the channel's width to ensure proper thickness. Move the towel-wrapped chopstick up and down vigorously to clean the channel, periodically removing the towel to wash off accumulated dirt until no more dirt is removed. Perform initialization for each window. The initialization method typically involves turning on the ignition switch, pulling and holding the switch to raise the window, continuing to hold for more than 3 seconds after the window reaches the top, releasing the switch and immediately pressing and holding it to lower the window to the bottom for more than 3 seconds, then pulling and holding the switch again to raise the window for more than 3 seconds after it reaches the top. Once initialization is complete, the window should regain its original functionality.

10

5

Share

What does the exclamation mark in the triangle on the dashboard mean?

How to Cancel the Maintenance Warning Light?

What Causes the Car to Pull to One Side When Braking?

How many days after painting can you wash the car?

Should You Engage the Handbrake First or Shift to P First When Parking an Automatic Transmission Car?

Is It Normal for Car Headlights to Get Hot?

What Causes Car Windows to Fail to Open?

In which year was the MINI born?

Where is the panoramic sunroof drain outlet located?

How to Check the Fuel Level of a Motorcycle?

What to Do When Your Car Gets Towed?