What does the engine icon on the car dashboard indicate as a fault?

1 Answers
BeckettDella
07/24/25 4:35am
When the engine icon appears on the car dashboard, it indicates an engine fault. Below are specific details about the engine icon displayed on the dashboard: 1. In a normal vehicle, when the key is turned to the ON position, the engine fault light on the dashboard will illuminate and automatically turn off after the car starts. 2. If the engine icon remains lit after the vehicle starts, it signifies an engine fault. 3. The engine fault signal is issued by the ECU (Engine Control Unit), which controls all electronic components of the engine, including the electronic throttle, fuel injectors, alternator, fuel pump, etc., covering various systems such as intake, exhaust, fuel, ignition, and timing.
Was this review help?
20
1
Share
More Forum Discussions

What tires should be replaced for the BMW M4?

For the BMW M4, the original tire brand is Michelin. There are two front tire sizes: 275/35R19 and 275/40R18, and two rear tire sizes: 285/30R20 and 285/35R19. Michelin was founded in 1889 in Clermont-Ferrand, France, and is one of the world's top three tire manufacturers. It currently operates across five continents with R&D centers in Europe, North America, and Asia. For the BMW M4 tires in daily use, pay attention to the following points: Regularly inspect the tire surface for defects such as cracks or deformations. Due to wear from driving, the tread grooves gradually become shallower. If the tread is worn flat, it will lose its drainage and anti-slip functions, significantly reducing the car's performance. Small cracks may seem minor but can lead to tire blowouts at high speeds. Additionally, promptly remove pebbles lodged in the grooves. Park on level ground whenever possible. Avoid parking on roads with thick, sharp, or pointed stones. Do not park near or in contact with petroleum products, acids, or other materials that can degrade rubber. After parking, avoid turning the steering wheel, as this accelerates tire wear. Do not splash water to cool overheated tires. In hot weather or during high-speed driving, tires can overheat, increasing air pressure. In such cases, stop to allow the tires to cool naturally. Never release air to reduce pressure or splash water to cool them, as this can cause abnormal aging of the tread rubber. Avoid sudden braking. Minimize frequent or hard braking to prevent accelerated tread wear caused by dragging between the tires and the road surface.
19
0
Share

What is the normal temperature range for car engine coolant?

Driving with engine coolant temperature between 85 to 95 degrees Celsius is normal. It's recommended to check the temperature gauge on the dashboard, ensuring the temperature indicator doesn't enter the red zone. The engine's cooling system is designed to maintain optimal operating temperatures, which enhances engine power output while reducing wear and fuel consumption. Both excessively high and low temperatures can adversely affect engine performance. Precautions for coolant usage include: 1. Regularly check coolant level and top up immediately if below minimum; 2. Inspect for turbidity or sediment - replace if contamination is found; 3. Never mix different coolant colors as formulations vary by vehicle model; 4. Before winter, measure the coolant's freezing point to prevent solidification.
13
2
Share

Which BMW model is the G20?

BMW G20 is the 7th generation of the BMW 3 Series, with G20 being the chassis code for this generation. The BMW G20 is built on the CLAR platform, which is BMW's advanced modular architecture. Models like the BMW 5 Series, 7 Series, 8 Series, X3, and the new Z4 are all built on this platform. The dimensions of the BMW G20 are 4709mm in length, 1827mm in width, and 1442mm in height, with a wheelbase of 2851mm. This car is equipped with two engine options: a 1.5T and a 3.0T, all paired with an 8-speed automatic transmission. The 3.0T engine version is further divided into high-power and low-power variants.
18
4
Share

How many kilometers should the brake pads of the Baojun 510 be replaced?

The front brake pads of the Baojun 510 need to be replaced approximately every 30,000 to 50,000 kilometers. The method for replacing the brake pads of the Baojun 510 is as follows: 1. Release the handbrake and loosen the hub screws of the wheel that needs the brake replacement (note: loosen them, do not completely remove them). Use a jack to lift the car properly. 2. Remove the tire. Before working on the brakes, spray the brake system with specialized brake cleaner to prevent powder from entering the respiratory tract and affecting health. 3. Remove the screws of the brake caliper. 4. Hang the brake caliper with a rope to avoid damaging the brake lines. Then remove the old brake pads. 5. Use a C-clamp to push the brake piston back to the innermost position. Install the new brake pads. 6. Reinstall the brake caliper and tighten the caliper screws to the required torque. Reinstall the tire and slightly tighten the hub screws. 7. Lower the jack and fully tighten the hub screws.
5
1
Share

Is the Bin Yue a Three-Cylinder?

Geely Bin Yue is a three-cylinder car, but besides the models equipped with the 1.5T three-cylinder engine, there are also models that use the 1.4T inline four-cylinder engine. Here is more information about the Geely Bin Yue: 1. The Geely Bin Yue is the first model built on Geely's new BMA global modular architecture, positioned as a compact SUV with a more youthful overall design, and equipped with L2 autonomous driving assistance technology. In terms of body dimensions, its length, width, and height are 4330×1800×1609 mm, with a wheelbase of 2600 mm. 2. The Geely Bin Yue is powered by the G-Power 260T (1.5TD) high-performance engine, co-developed with Volvo, delivering a maximum power of 177 ps/5500 rpm and a peak torque of 255 N·m/1500-4000 rpm, surpassing the performance of a 2.5L naturally aspirated engine.
13
4
Share

What is the engine model of the Volkswagen Polo?

The Volkswagen Polo is primarily equipped with two turbocharged engines: the 1.2L TSI and 1.6L TDI, as well as naturally aspirated gasoline engines in 1.2L and 1.4L displacements. Here is more information about the Volkswagen Polo: 1. The Volkswagen Polo was introduced in 1975. Over the next 30 years, it underwent five generations of product evolution, with total production exceeding 7 million units, and it long held the top position in sales of economical small cars in Germany. 2. The new Shanghai Volkswagen Polo was officially launched on May 25, 2014. The new Polo is powered by the EA211 series of engines, still offering naturally aspirated engines in 1.4L and 1.6L displacements. Although the displacement remains unchanged, the new engines provide stronger power, with maximum outputs of 66kW and 81kW, respectively, along with improved fuel economy.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.