What does the engine auto start-stop system mean?

1 Answers
DelMadelyn
07/30/25 8:39am
Engine auto start-stop system: A system that automatically shuts off the engine when the vehicle comes to a temporary stop (such as waiting at a red light) during driving, and automatically restarts the engine when it's time to move forward again. Advantages and disadvantages of the engine auto start-stop function: 1. Advantages: It can reduce unnecessary fuel consumption, lower emissions, and improve fuel economy. In urban traffic when waiting for traffic signals or during traffic jams, it can minimize engine idling time. Additionally, after the engine shuts off, its power supply can replace the belt pulley to provide operating power for the engine cooling fan and in-car air conditioning. 2. Disadvantages: It requires more durable starters and batteries. Conventional starter designs allow for high operating currents but are intended for very short usage periods. Repeated use of the starter can easily cause overheating and damage. Therefore, starters with auto start-stop functionality must be significantly more durable than regular starters.
Was this review help?
10
3
Share
More Forum Discussions

What are the reasons for the windshield wiper not spraying water?

Specific reasons for the windshield wiper not spraying washer fluid: 1. Pipe blockage: Frequent driving on unpaved roads can cause tiny dust particles to enter the spray holes of the wiper. Over time, the dried dust can block the spray holes, preventing the wiper from spraying water. Simply insert a brush into the wiper spray holes to clean out the dust or attached dirt, and turn on the wiper spray switch while cleaning. 2. Water level too low: The washer fluid container for the wiper is designed in the engine compartment. If the water level is too low, it will also prevent water from spraying. In this case, just add water to the washer fluid container.
11
2
Share

Is There a Difference Between Good and Bad Brake Fluid?

Here are the differences between good and bad brake fluid: 1. Taste: Genuine brake fluid has a slightly sweet smell, while fake brake fluid smells foul, with an alcohol-like odor. 2. State: Genuine brake fluid is yellow, resembling honey diluted with water, and feels warm to the touch; fake brake fluid is made by mixing water and alcohol, so it appears clear. Using fake brake fluid in a vehicle can cause brake failure while driving, leading to serious consequences. Below are the reasons for brake fluid leakage: 1. Brake hose rupture: The brake hose connects the brake pump and the brake caliper. When the brake pedal is pressed, brake fluid is transmitted through the hose to the caliper piston, which then pushes the brake pads to squeeze the brake disc, creating the braking effect. If the brake hose ruptures, oil leakage will inevitably occur, affecting the vehicle's braking performance. Therefore, timely repairs are essential. 2. Damaged sealing ring: Brake fluid is highly corrosive. Although sealing rings are resistant, they can age slightly over time, reducing their sealing effectiveness and leading to oil leakage. Simply replacing the sealing ring can resolve this issue. 3. Loose or damaged hose screw: The hose screw is used to seal the brake fluid inside the hose. If the screw is damaged, oil leakage will naturally occur. If it is only loose, tightening it will suffice.
8
2
Share

Do You Need to Press the Clutch When Braking?

When the vehicle speed is slow, you can first press the clutch to reduce speed, then press the brake to reach a safe distance. Here is the relevant content introduction: 1. State: When the vehicle speed is fast, pressing the clutch first will put the car in a neutral coasting state. 2. Hazard: This will reduce the lifespan of the brake discs, so you should press the brake first. Here is extended information about the replacement time of the car clutch: 1. Basis: The replacement of the clutch disc is not based on time but on mileage. 2. Mileage: Generally, a car needs to replace the clutch disc at around 100,000 kilometers. 3. Personal habits: The replacement mileage of the clutch disc is related to personal usage habits.
17
5
Share

How Long Can Headlight Restoration Last?

Headlight restoration can last for two to three years. Here is the relevant information: 1. Headlight composition: The headlight cover is injection-molded from polycarbonate or polymethyl methacrylate plastic. Whether it's halogen, xenon, or LED lights, they all generate a significant amount of heat when illuminated. This heat accelerates the aging of the plastic, causing the cover to lose its clarity and transparency, even turning dull and yellow, which directly affects the lighting effect. 2. Causes of headlight wear: Car headlights are a crucial component. After prolonged use, you may notice that the light emitted becomes dim and yellow, with reduced brightness, especially in halogen headlights, where this is more pronounced. There are two main reasons for the decrease in light brightness: first, external factors like windblown sand and gravel leave scratches and dust on the cover; second, the heat generated by the bulb inside causes the plastic cover to age and turn yellow.
7
0
Share

How to align the two points on the 465 camshaft?

465 camshaft two-point alignment steps are as follows: 1. Rotate the crankshaft to position the No.1 cylinder piston at the compression top dead center, aligning the timing marks on the camshaft and crankshaft sprockets. 2. When the No.4 cylinder piston is at top dead center, the timing marks should align, with both the intake and exhaust valves of the No.4 cylinder in the closed position. 3. Remove the bolt from the camshaft sprocket, then take off the timing chain and camshaft sprocket. 4. Install the timing chain onto the camshaft sprocket, secure the sprocket so the chain hangs down, and align the timing marks on the camshaft and crankshaft sprockets. Align the locating pin holes on the sprocket with those on the camshaft, then mount the sprocket onto the camshaft. 5. Lubricate the timing sprocket and chain with engine oil, rotate the crankshaft two full turns, and check if the engine timing marks are aligned. If the timing marks do not align, repeat the above steps to redo the operation.
8
4
Share

What are the basic essentials of learning to drive?

Learning to drive requires mastering the use of gear shifting, clutch, and brakes. Here are some tips on the essentials of learning to drive: 1. Gear Shifting: When shifting gears, you must progress from lower to higher gears one by one, without skipping any. Shift up as speed increases. However, when downshifting from higher to lower gears, you can skip gears based on speed, such as shifting directly from 5th to 2nd or 3rd gear. 2. Clutch and Brakes: The left foot controls the clutch, while the right foot manages the brake and throttle. Since the brake and throttle are mutually exclusive, it's best to control them with one foot. When braking, do it progressively, using inertial braking.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.