What does Super Select 4WD mean?

1 Answers
Emerson
07/29/25 1:36pm
Super Select 4WD is an electronically assisted SS4-II system. Here is the relevant introduction about Super Select 4WD: 1. The Super Select 4WD system means that the vehicle can freely switch between 2H and 4H gears within a speed of 100 km/h. When in the 4H position, it is equivalent to a full-time four-wheel drive model, providing better traction and driving force. When in the 2H position, pure rear-wheel drive can improve the vehicle's fuel economy to a certain extent, giving drivers greater freedom of choice. 2. Super Select 4WD has a history of many years. Since its debut in the early 1990s, it has been successively equipped on third-generation (V73, V77, etc.) and fourth-generation (V93, V87, V97, etc.) models. The Super Select 4WD has also evolved from the first-generation purely mechanical SS4 system to the current electronically assisted SS4-II system.
Was this review help?
4
5
Share
More Forum Discussions

What to Do When the Car Has Power and Fuel but Won't Start?

When encountering a situation where the car has power and fuel but won't start, you can analyze it from the following two dimensions: 1. First, check whether the battery has power. If it doesn't, it needs to be replaced in time. 2. Check whether the gear is in the P position. Ensure the gear is in the P position when starting the car. If the car can start in D or R gear, the sudden movement of the vehicle at the moment of ignition is undoubtedly a huge safety hazard, so extra attention should be paid. 3. The battery is one of the most likely causes of the car not starting. In many cases, the sudden loss of power in the battery is due to the battery's lifespan being reached or the headlights being left on for too long.
12
2
Share

What are the reasons for air leakage in the dryer assembly?

Air leakage in the dryer assembly may be due to a faulty desiccant pressure regulator valve. Solutions: Simply weld or replace the damaged part, replace the O-ring if it is worn out, or clean the check valve and inspect the pipeline behind the dryer to locate the leak and ensure it is sealed. This will resolve the frequent air leakage issue in the dryer. Usage Notes: After prolonged use, the drying cylinder in the dryer will lose its drying function. It is recommended to replace the drying cylinder annually. Do not arbitrarily adjust the pressure adjustment screw to prevent inaccurate unloading pressure and thread damage, which could render the dryer unusable. Regularly clean the check valve and inspect the pipeline behind the dryer to locate leaks and ensure they are sealed.
3
3
Share

What is the engine shutdown procedure for the Audi A6 as per the manual?

The engine shutdown procedure for the Audi A6 as per the manual is: First, press and hold the brake pedal, then shift to N (neutral), engage the parking brake, press the engine stop button, shift to P (park), and finally release the brake pedal to complete the shutdown operation. The starting procedure for the Audi A6 is: Press and hold the brake pedal, shift to N or P, then press the start button to ignite the engine. The Audi A6 is a luxury vehicle produced by Audi, available in both sedan and station wagon variants. The vehicle dimensions are 4940mm in length, 1890mm in width, and 1470mm in height, with a wheelbase of 2924mm. It is equipped with a multitronic continuously variable manual transmission.
7
1
Share

Why does the car start to shake when driving at 120 km/h on the highway?

When the car reaches 120 km/h, it is in a high-speed driving state. The shaking that occurs at this speed can be analyzed from the following two dimensions: 1. The vibration gradually intensifies as the speed increases. 2. When vibration occurs at a certain high speed and causes the steering wheel to shake, first lift the drive axle, place safety blocks in front of the front wheels, start the engine, and gradually shift into higher gears to bring the drive wheels to the final test vibration speed. 3. If both the body and the steering wheel shake at this point, the vibration is caused by the drivetrain, as the front wheels and axle are stationary at this time. If the car does not shake at the final test vibration speed, the cause of the vibration lies in the front axle, and further diagnosis and troubleshooting are required.
18
1
Share

Is Windshield Tinting Necessary?

Yes, here are the benefits of applying window film: 1. Heat and Sun Protection: The film can block heat generated by infrared rays. 2. UV Protection: Medium and long waves of ultraviolet rays can penetrate thick glass, but applying heat-insulating film can block most UV rays. 3. Safety and Explosion Prevention: The base layer of the film is made of polyester, which is highly resistant to tearing and penetration. Combined with the adhesive layer, the film enhances the glass's strength, preventing injuries from accidental glass breakage. 4. Creating a Private Space: By choosing the appropriate type, the film ensures that the interior of the car is not visible from the outside while maintaining clear visibility from inside, preserving privacy and safety. 5. Reducing Air Conditioning Consumption: Applying heat-insulating film compensates for the loss of air conditioning cooling capacity, instantly lowering the interior temperature and achieving a certain degree of fuel savings.
16
0
Share

What is the reason why a diesel car won't start after running out of fuel and refueling?

Here are the specific reasons why a diesel car won't start after running out of fuel and refueling: 1. Electrical circuit failure: It may be due to low-voltage power interruption during driving, causing the engine to stall. 2. Electrical component failure: Usually caused by faults in the ignition coil, capacitor, or electronic ignition module. The symptom is that the engine can start initially but stalls after a while. 3. Fuel system failure: Damage to the fuel pump, fuel line rupture, clogged carburetor fuel inlet, or empty fuel tank. 4. Sensor failure: Faults in the throttle position sensor, intake air flow sensor, intake pressure sensor, crankshaft position sensor, camshaft position sensor, etc. If these sensors malfunction, it can also cause the engine to stall. 5. Other failures: Engine timing system disorder. Incorrect timing system calibration or engine valve issues.
4
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.