What does 'stop' mean in a car?

1 Answers
VictoriaLynn
07/29/25 6:03pm
The 'stop' light in a car refers to the mandatory stop warning light. When this light illuminates, the engine must be shut down immediately. Here are the details: The 'stop' warning light is not an independent indicator—it is interconnected with the engine oil pressure warning, low brake fluid level warning, coolant temperature gauge, and electronic brake force distribution system fault warnings. The dashboard also features indicators for coolant temperature, oil pressure, air pressure, engine status, and cabin conditions. If any of these systems encounter an issue, the 'stop' light will activate. For instance, if the engine overheats during operation, triggering the coolant temperature warning light, the 'stop' light will also illuminate to alert the driver of an engine malfunction. Additionally, the dashboard includes a yellow warning light alongside the red 'stop' light—yellow indicates a general fault, while red signifies a severe malfunction.
Was this review help?
5
4
Share
More Forum Discussions

Does Replacing the Rear Bumper Beam Cause Depreciation?

From the perspective of used cars, replacing the bumper does have an impact on the vehicle, but it is not significant. Bumper replacement falls under physical depreciation, as there is a clear distinction between original and replaced parts. However, simply replacing the bumper does not greatly affect the overall performance of the vehicle, so its impact on depreciation is minimal. Relevant information about the car's bumper beam is as follows: 1. Introduction One: The role of the bumper beam is to transmit impact force during severe collisions and to protect the car body and some components from damage during minor collisions. The bumper beam is crucial for a car, but it is not considered a structural component because it is connected to the car body via bolts. 2. Introduction Two: Both the front and rear of a car have bumper beams, though some cars may lack a rear bumper beam. During minor collisions, the front bumper beam protects the radiator, condenser, engine, etc., while the rear bumper beam safeguards important areas like the trunk floor and rear panel. The bumper beam is bolted to the car's longitudinal beams, with energy-absorbing boxes located at the connection points between the bumper beam and the longitudinal beams.
8
1
Share

How long does it take for non-motor vehicle violation records to be deleted?

Non-motor vehicle violation records will be permanently deleted within three to five working days after payment. Here are the details: 1. Hazards: Running red lights at will, vehicles avoiding non-motor vehicles, causing road traffic congestion. Occupying motor vehicle lanes, motor vehicles cutting in are illegal driving behaviors of non-motor vehicles, leading to traffic congestion and accidents. Non-motor vehicle owners are easily injured, and the consequences are unpredictable. Non-motor vehicles going against the traffic, vehicles driving on the right side are the most basic traffic knowledge. Disrupting road traffic order and posing safety hazards to normally driving vehicles. 2. Application: Handling violations requires documents, the original and duplicate of the violating vehicle's driving license, the original and duplicate of the driver's license, cash or a bank card designated by the traffic police department, and processing at the business hall of the traffic management department. Personal signature is required, and ID must be presented. Methods to check violations include inquiries at traffic law enforcement stations, online inquiries at the traffic police vehicle management office, mobile app software inquiries, violation SMS reminders, and phone self-service inquiries. To handle traffic violations, the vehicle owner must personally go to the local vehicle management office to receive the penalty notice and sign it. The original and duplicate of the motor vehicle driving license, the original and duplicate of the driver's license, and cash are required.
6
5
Share

What is the lifting vehicle for repairing street lights called?

The vehicle used for repairing street lights is called a street light maintenance engineering vehicle, which belongs to the category of special vehicles. Here is more relevant information: 1. Vehicle positioning: The vehicle should be parked on firm and level ground with a slope not exceeding five degrees. 2. Requirements before leaving the cab: Engage the parking brake and lock it, set the transmission to neutral. Depress the clutch, turn on the power assist switch, then release the clutch to start the oil pump. Requirements when leaving the cab: Secure the wheels with chocks, set up warning signs, mark the work area, and alert pedestrians and vehicles to avoid the area. 3. Precautions for operating the vehicle: Start with the outrigger operation first, then return to the rotating platform, and finally operate within the work bucket. Always monitor the working condition of the vehicle, be aware of the range of the lifting arm to avoid reaching the limit, which could cause instability of the entire vehicle, leading to structural damage or personal injury. In summary, factors affecting the stability of the vehicle include the hardness and slope of the road surface, the weight of the work bucket, tire pressure, and the span of the outriggers. Therefore, observe the pressure gauge switch, and when the pointer reaches around 3Mpa, you can proceed with the next steps.
14
1
Share

What is the solution when the car starts and the doors automatically lock after the driver exits?

The solutions when the car starts and the doors automatically lock after the driver exits are: 1. Use the spare key; 2. Contact a locksmith company; 3. Break the car window. The steps to start an automatic transmission car are: 1. Turn the ignition key to the power position; 2. Press the foot brake and shift the gear from P to N; 3. Release the foot brake to start the engine; 4. Warm up the car while stationary; 5. Press the foot brake, shift the gear from N to D, and release the handbrake; 6. Slowly release the foot brake and gently press the accelerator to start smoothly. The steps to start a manual transmission car are: 1. Fully depress the clutch pedal; 2. Move the gear lever to engage 1st gear; 3. Lightly press the turn signal lever downward to activate the left turn signal, alerting vehicles in front and behind; 4. Press the horn button to alert pedestrians in front of the vehicle that you are about to start; 5. Release the vehicle's handbrake; 6. Lift the left foot slowly until the clutch reaches the semi-engaged state and the vehicle begins to vibrate slightly; 7. As the vehicle starts moving, release the clutch and gently press the accelerator.
3
2
Share

How long after canceling the subject three appointment can I make a second appointment?

You can make a second appointment the day after canceling the subject three appointment, but please note: 1. Appointment feedback: Whether the appointment is successful depends on the total number of appointments and your ranking, with the system's actual feedback being the main determinant. 2. Factors affecting the appointment: Multiple cancellations may impact the success rate of your next appointment. The content of the subject three test is as follows: 1. Road driving skills: Includes preparation for getting on the vehicle, simulated nighttime lighting test, starting, driving in a straight line, shifting gears, changing lanes, pulling over, going straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting vehicles, overtaking, making U-turns, and nighttime driving for large buses, tractors, city buses, medium-sized buses, large trucks, small cars, small automatic transmission cars, low-speed cargo trucks, and small automatic transmission passenger cars for the disabled. The test content for other permitted vehicle types is determined by the provincial traffic management departments of public security authorities. 2. Safe and civilized driving knowledge: Includes requirements for safe and civilized driving operations, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-accident handling knowledge.
17
2
Share

Where to Buy Windshield Washer Fluid?

Windshield washer fluid can generally be purchased at large supermarkets or auto parts stores. Below is some extended information about windshield washer fluid: 1. Windshield washer fluid is the common name for automotive windshield cleaning fluid. It is a consumable item in vehicle use. 2. High-quality automotive windshield washer fluid is mainly composed of water, alcohol, ethylene glycol, corrosion inhibitors, and various surfactants. 3. When the transparency of the front windshield decreases, spraying some windshield washer fluid can provide a clear and bright view. 4. Especially during night driving, dust on the glass can scatter light, making it necessary to spray windshield washer fluid to maintain the front windshield in optimal transparency.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.