What does starting the car mean?

1 Answers
DelOscar
07/30/25 3:28am
Starting the car is the fundamental technique and experience for driving safety. Steps for starting the car: Engage the handbrake (to prevent sliding); insert the key; turn on the power and perform a self-check for 5 seconds; press the foot brake; shift from P to N gear; start the engine and warm up for 15 seconds (during this time, fasten the seatbelt and adjust the rearview mirror); shift into D gear; release the handbrake; slowly release the foot brake; start moving. Precautions for starting the car: Carefully inspect the surroundings of the vehicle, paying attention to any obstacles under the car or around the body. Cold starts require warming up the engine, with the warm-up time depending on the temperature; generally, it is sufficient to start when the idle speed returns to normal. Always remember to fasten the seatbelt and check if the driver's seat and rearview mirror positions are appropriate; adjust them if necessary.
Was this review help?
20
1
Share
More Forum Discussions

Can You Downshift Directly from Fifth Gear to Second Gear in a Manual Transmission?

Manual transmission downshifting can be done directly from fifth gear to second gear. Manual Transmission Downshifting Techniques First gear is used for speeds of 0 to 15 km/h, typically for starting the car or climbing hills; second gear is for 15 to 20 km/h, often used when turning; third gear is for 20 to 40 km/h, suitable for passing through intersections; fourth gear is for 40 to 60 km/h, and fifth gear is for speeds above 60 km/h. Manual Transmission Precautions: Whether upshifting or downshifting, it is not necessary to follow a strict order. However, it is crucial to ensure that the gear matches the speed to avoid damaging the transmission.
12
4
Share

How to Set Cruise Control on Civic?

Here are the steps to set cruise control on Civic: 1. Press the main button on the left. 2. When it is safe to do so, accelerate to over 40 km/h and press the SET button once to activate cruise control. 3. After entering cruise control mode, you can adjust the speed using the up and down buttons. 4. To cancel cruise control, either press the brake or the cancel button on the right. Always ensure safety before activating cruise control. It is recommended to use it only on highways with light traffic. Additionally, the system requires the car speed to exceed 40 km/h to activate.
2
1
Share

Can Kawasaki Motorcycles Go on the Highway?

Under normal circumstances, Kawasaki motorcycles can go on the highway. Here are the details: Legal regulations: The "Implementation Regulations of the Road Traffic Safety Law of the People's Republic of China" stipulate the following: Highways must indicate the speed limits for lanes, with the maximum speed not exceeding 120 kilometers per hour and the minimum speed not less than 60 kilometers per hour. Motorcycles must not exceed 80 kilometers per hour. Precautions: When riding a motorcycle on the highway, the driver must wear a helmet; the motorcycle must have a displacement of 125cc or more; motorcycles cannot carry passengers, only the driver is allowed; the speed on the highway must be greater than 60 or less than 80 kilometers per hour; motorcycles must ride on the right side of the highway.
20
1
Share

What Are the Main Raw Materials of Brake Pads?

The main raw materials of brake pads are adhesives, reinforcing fibers, fillers, and friction modifiers. Below is a detailed introduction about them: 1. Adhesives include resins and rubber powders: Their function is to liquefy and then solidify at high temperatures, turning the brake pad from powder into a solid block. 2. Reinforcing fibers serve as the skeleton of the brake pad: These include aramid fibers, steel wool fibers, copper fibers, mineral fibers, ceramic fibers, potassium titanate whiskers, etc. 3. Fillers: Different raw materials of brake pads have varying mesh sizes and diameters, requiring certain gaps to be filled. 4. Friction modifiers increase friction: These are materials harder than the brake disc, such as aluminum oxide, zirconium silicate, brown corundum, etc.
14
1
Share

What are the components of the engine block assembly?

The engine block assembly mainly consists of the cylinder head, cylinder head cover, cylinder gasket, cylinder block, main bearing cap, and oil pan. Definition of the engine block assembly: The engine block assembly serves as the framework of the engine, providing the mounting base for the crankshaft connecting rod mechanism, valve train, and other major components of the engine's various systems. Classification of the engine block assembly: Features of dry cylinder liners: The outer wall does not directly contact the cooling water. Wall thickness ranges from 1 to 3mm. They offer good strength and rigidity but are more complex to manufacture, difficult to disassemble, and have poor heat dissipation. Features of wet cylinder liners: The outer wall directly contacts the cooling water. Wall thickness ranges from 5 to 9mm. They provide excellent heat dissipation, uniform cooling, and easier manufacturing. However, their strength and rigidity are inferior to dry liners, and they are prone to water leakage.
6
1
Share

What does driving illusion include?

Driving illusions include light illusion, slope illusion, distance illusion, and curvature illusion. Light illusion: Strong sunlight mixed with the shade of trees on both sides of the road, alternating between bright and dark, can easily dazzle the eyes, creating a light illusion that leads to operational errors. In addition to sunlight, the glare from reflective objects, the strong light from high beams during night driving, and the glare from oncoming vehicles can all make it difficult for the driver's vision to adapt momentarily, causing a light illusion. Distance illusion: While driving on the road, drivers may sometimes misjudge the length of oncoming vehicles, the distance between vehicles during a meeting, or the following distance, leading to insufficient meeting distance or too close a following distance, resulting in accidents. When meeting another vehicle, no matter how great the speed difference between the two vehicles is, the meeting point always seems to be at the midpoint between the two vehicles.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.