What does 'push' mean on a sedan?

What Causes the Rear Wheel to Make a Rumbling Noise on Bumpy Roads?

When a car makes a "rumbling" noise during continuous bumps, it is highly likely due to the lower control arm ball joint. The grease inside the lower control arm ball joint may dry out, leading to internal wear and the creation of gaps, which ultimately results in driving noise. Below is more information about the functions of the lower control arm ball joint:1. Buffering and vibration damping. 2. Transmitting torque. 3. Maintaining vehicle stability, improving comfort and safety performance. 4. Guiding role. It works with the suspension system to adjust camber and toe-in, allowing the vehicle to achieve certain steering angles. 5. Enhancing tire grip for better handling, providing the driver with a superior control experience. 6. Bearing and transmitting loads from various directions, mitigating impacts or changes in vehicle position caused by braking, road conditions (uneven surfaces), acceleration, or steering.

10

4

Share

What does it mean when the SVS light on the dashboard is on?

The SVS light on the dashboard indicates that the engine control unit has detected an error signal from a sensor or that the sensor has exceeded its operational standards. When the ignition is turned on, the SVS indicator light will illuminate for an automatic check and then turn off after a few seconds. More detailed information is as follows: 1. If the SVS light is on, you can try to start the engine. If the engine fails to start, it might be due to an abnormal fuel pump that cannot supply fuel properly to the engine. If the engine starts, it could be a fault with another sensor. In this case, the car may still be drivable, but the issue could affect normal vehicle operation, such as increased fuel consumption or body vibrations. 2. If the SVS light is accompanied by signs like increased combustion chamber temperature or the oil pressure warning light, continuing to drive may lead to accelerated engine wear and early engine damage.

15

0

Share

Where is the Fista's engine produced?

The Fista's engine is manufactured in China. It uses the 1.6t engine from the Veloster. The Fista model is G4LD, with a maximum power of 140kw, maximum power speed of 6000 rpm, maximum torque of 265 Nm, and maximum torque speed ranging from 1500 to 4500 rpm. Here are some daily maintenance methods for the Fista's engine: Use lubricating oil of appropriate quality grade. For gasoline engines, choose SD--SF grade gasoline engine oil based on the additional devices of the intake and exhaust system and usage conditions; for diesel engines, select CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements; Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid malfunctions, change the oil regularly according to usage conditions and keep the oil level moderate; When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve and bring contaminants back to the lubrication area, accelerating engine wear and internal pollution; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, clogging the filter and oil holes, making engine lubrication difficult and causing wear; Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine's normal operation but also extends the overall lifespan of the radiator and engine.

12

3

Share

What is the emission standard for 2008 cars?

Most cars from 2008 comply with the China III emission standard, with a very small portion meeting the China IV standard. The emission standard of a car can vary depending on the brand, model, and region. More details are as follows: 1. To accurately determine the emission standard of a specific car, it is necessary to know the brand, model, and the region where it was sold. 2. The China III standard refers to the national third-phase emission standard, equivalent to the Euro III standard. It limits the content of exhaust pollutants to levels similar to Euro III, but with an additional requirement for new cars to be equipped with an OBD (On-Board Diagnostics) system. The OBD system features more detection points and systems, including oxygen sensors at both the inlet and outlet of the three-way catalytic converter.

7

1

Share

How to Solve Insufficient Power of Vehicles in Plateau Areas?

Solutions for insufficient power of vehicles in plateau areas are as follows: 1. Replace the air filter. A clean air filter ensures the quality and quantity of air intake. The plateau is already oxygen-deficient, and a dirty air filter will only worsen the plateau reaction. 2. Use high-quality fuel. Poor fuel quality leads to incomplete combustion, which becomes more severe in oxygen-thin conditions. Therefore, it is essential to refuel at reputable gas stations with gasoline that meets the required octane rating. 3. Preferably drive an off-road vehicle. Off-road vehicles generally have strong power, which can compensate for the power decline caused by oxygen deficiency. Additionally, off-road vehicles are more suitable for driving in wild conditions. Insufficient power is a significant drawback, and since environmental factors cannot be changed, switching to a more suitable vehicle becomes the best option.

2

4

Share

What are the major maintenance items for the Magotan at 60,000 kilometers?

Replace engine oil and oil filter, replace fuel filter, replace cabin air filter, replace engine air filter, replace brake fluid, replace transmission fluid, replace spark plugs. Here is more information about maintenance: 1. Maintenance intervals: First service at 5,000 kilometers, then every 10,000 kilometers thereafter. Brake fluid should be replaced every 2 years. 2. Purpose of maintenance: To ensure your vehicle always operates in optimal condition, eliminate potential hazards in advance, prevent malfunctions, slow down the deterioration process, maintain a clean appearance, extend the vehicle's service life, and reduce maintenance costs.

17

1

Share

What does 'push' mean on a sedan?

What Causes the Rear Wheel to Make a Rumbling Noise on Bumpy Roads?

What does it mean when the SVS light on the dashboard is on?

Where is the Fista's engine produced?

What is the emission standard for 2008 cars?

How to Solve Insufficient Power of Vehicles in Plateau Areas?

What are the major maintenance items for the Magotan at 60,000 kilometers?

How often should the transmission fluid be changed for the Mazda Atenza?

How to open the hood of a Kia K3?

What is the Accent car?

What are the dimensions of the Geely Xingyue?