What does 'pressure loss detected' mean?

2 Answers
LaKathryn
07/25/25 4:08am
The meaning of 'pressure loss detected' is that the tire pressure is too low, which is a warning issued by the tire pressure monitoring system. After this situation occurs, the driver should check which tire has insufficient pressure and inflate it immediately. If the tire has an air leak, it should be repaired promptly. Tires are an important component of a vehicle, being the only part that contacts the ground. They are crucial for the driving stability and safety of the vehicle. Tire pressure should neither be too high nor too low. If the pressure is too low, the tire may experience wave-like deformation during high-speed driving, increasing the risk of a blowout and reducing the tire's service life.
Was this review help?
9
1
Share
WestonFitz
08/10/25 5:17pm
A couple of days ago, I was driving home when a warning suddenly flashed on the dashboard: 'Pressure loss detected.' I was a bit confused at first, but after getting out of the car, I noticed the tire was a bit flat. Pressure loss means insufficient tire pressure, which could be caused by a leak or temperature changes. When the pressure is low, driving feels heavier on the steering wheel, and handling worsens; tires wear out much faster—I had to replace two tires last year because of this, costing me over a thousand bucks. Worse yet, if you're driving at high speeds, the tires could overheat and blow out. Once, I neglected it, and the tire pressure dropped to half, nearly causing me to skid on a wet road. Now, I always keep a portable air pump in the car. Whenever I see a warning, I stop immediately to check. The standard pressure values are listed on a sticker by the door—just inflate accordingly. Otherwise, head to a repair shop right away—don't delay. Safety first! Developing a habit of regular checks can prevent such issues.
Was this review help?
12
5
Share
Expand All
More Forum Discussions

How to Prevent Car Tire Blowouts in Summer?

There are four key points to prevent car tire blowouts in summer. Here are the relevant tips: 1. Regularly check tires for damages or bulges. Aging tire materials are prone to cracking, so drivers should develop the habit of inspecting tires to ensure safe driving. 2. Avoid splashing cold water to cool down tires in summer, as rapid cooling may cause cracks. Let tires cool naturally. 3. Tire pressure is a major factor in blowouts, so appropriately reduce tire pressure. 4. Drivers should try to avoid potholed roads, as severe impacts can damage both tires and wheel rims.
19
5
Share

How to Activate the Auto-Lock Function on the Accord?

Here are the steps to activate the auto-lock function on the Accord: 1. Open the driver's side door of the GAC Honda Accord. 2. Press the brake pedal of the GAC Honda Accord to prepare for engine start. 3. Press the one-touch start button of the GAC Honda Accord. 4. All dashboard lights of the GAC Honda Accord will illuminate, indicating the engine has started. 5. Press and hold the lock button on the driver's door of the GAC Honda Accord for more than 10 seconds to unlock. When the vehicle speed reaches the preset value (usually between 10 km/h and 20 km/h), the lock button will automatically engage to prevent accidental door opening. This is the most common auto-lock method used in many vehicle models.
16
1
Share

How Many Kilometers to Change Transmission Oil for Automatic Cars?

There is no unified standard, but generally, automatic transmission oil should be changed every 2 years or 40,000 kilometers, while manual transmission oil is typically changed every 40,000 to 60,000 kilometers. Transmission oil is a lubricant that keeps the gear system clean, ensuring the transmission operates smoothly and extending the lifespan of the transmission components. Below are the methods for changing transmission oil: 1. Gravity Drain: Similar to changing engine oil, loosen the oil pan bolt and let the transmission oil drain out by gravity. This is the simplest method, but it doesn't completely remove all the old oil due to mechanical design constraints like recesses and uneven surfaces. 2. Machine Flush: New transmission oil is added to a flushing machine, which connects to the transmission's oil lines. Under hydraulic pressure, the new oil pushes out the old oil, resulting in a cleaner oil line. The more new oil used, the cleaner the system becomes. A machine flush typically requires about 10-13 liters of transmission oil and takes approximately 40-80 minutes. 3. Oil Pan Removal: This method involves removing the oil pan for a thorough cleaning and also allows for cleaning the oil filter. However, due to the labor-intensive process, most 4S shops do not perform this method.
15
3
Share

Where is the cabin air filter located in the BAIC Senova D50?

The cabin air filter in the BAIC Senova D50 is located under the drainage trough in front of the front passenger seat. For the cabin air filter, the recommended replacement cycle is twice a year, specifically once in spring and once in autumn; the cleaning cycle is once a year, preferably in spring. Below is an introduction to the cabin air filter in the BAIC Senova D50: 1. It ensures the filter fits tightly against the housing, preventing unfiltered air from entering the cabin. 2. It separates solid impurities such as dust, pollen, and grinding particles from the air. 3. It adsorbs moisture, soot, ozone, odors, carbon oxides, SO2, CO2, etc., from the air, with strong and long-lasting moisture adsorption capabilities. 4. It prevents car windows from fogging up, ensuring clear visibility for drivers and passengers and safe driving; it provides fresh air to the cabin, preventing occupants from inhaling harmful gases and ensuring driving safety; it effectively sterilizes and deodorizes. 5. It maintains clean air in the cabin, preventing bacterial growth and creating a healthy environment; it effectively separates solid impurities such as dust, core powder, and grinding particles from the air; it effectively intercepts pollen, ensuring that drivers and passengers do not experience allergic reactions that could affect driving safety.
2
1
Share

Where are the USB ports located on the Lynk & Co 01?

The Lynk & Co 01 is equipped with a total of 5 USB ports. Among them, 2 ports are located in the front glove box, 2 ports are positioned near the rear air vents, and 1 port is situated beside the central rearview mirror. Below is some relevant information about the Lynk & Co 01: 1. The Lynk & Co 01 is a new-era SUV designed for urban young people, officially launched on November 28, 2017. 2. The Lynk & Co 01 is the first model developed by Lynk & Co based on the CMA (Compact Modular Architecture) platform. 3. The Lynk & Co 01 is the world's first passenger car to feature Bosch's latest ESP9.3 high-dynamic version.
1
2
Share

Does the Zhonghua V3 have navigation?

Zhonghua V3 comes with built-in navigation. The usage method is as follows: first, turn on the navigation button, then input the destination, select the input location as the destination, and start navigation. During the journey, follow the navigation prompts, which include red light warnings and speed limit alerts, providing the driver with a safe and stable driving experience. The upgrade method for Zhonghua V3 navigation is as follows: 1. Use a computer to download free map software packages from GPS forums online. 2. Extract the map package and modify the appropriate port and baud rate. 3. Transfer the modified map folder to the navigation device's map memory card. 4. Turn on the navigation device, set the navigation path, and complete the upgrade.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.