What does MT mean in manual transmission?

1 Answers
Venus
07/29/25 8:26pm
MT is the abbreviation for manual transmission. MT is also known as a mechanical transmission, which requires the driver to manually shift the gear lever (commonly known as the "gear stick") to change the gear meshing position inside the transmission, thereby altering the gear ratio to achieve speed variation. The advantages and disadvantages of manual transmission are as follows: Advantages: 1. Faster response during acceleration and overtaking (for skilled drivers); 2. High transmission efficiency; 3. Simple structure, easy to repair. Disadvantages: 1. Relatively complex operation (requires perfect coordination between the clutch and gear lever); 2. Higher driving skill requirements (improper operation can easily lead to gear dragging or stalling).
Was this review help?
12
4
Share
More Forum Discussions

What are the effects of prolonged idling on a car?

Prolonged idling of a car can have several effects: 1. If the engine idles for a long time, the throttle opening will be very small, and the fuel injector will spray a high concentration of fuel to keep the engine running. Therefore, idling itself is more likely to cause carbon deposits compared to driving or high-speed driving. Prolonged idling will definitely lead to more severe carbon deposits in the engine. 2. According to tests, idling for three minutes consumes fuel equivalent to driving one kilometer. This means that idling for two hours can consume almost 2-3 liters of fuel. 3. When the engine idles, the temperature and pressure in the cylinders are relatively low, prolonging the preparation time for fuel ignition. Additionally, the sealing of the cylinders decreases, making it easier to produce knocking sounds and shortening the engine's lifespan. 4. During prolonged idling, the engine's air-fuel mixture becomes too rich, and the exhaust gas contains low oxygen levels. The unburned mixture can ignite at the location of the three-way catalytic converter, potentially damaging it.
18
5
Share

How to Use Lincoln Cruise Control?

First, press the button on top of the cruise control switch, accelerate to over 40 km/h, then pull the cruise control lever downward for more than 2 seconds. At this point, you can release the throttle and the lever. Relevant details are as follows: 1. Usage on Highways: Do not use cruise control in special weather conditions or road sections. Generally, cruise control is used on highways and should not be used in urban areas or sections with heavy traffic. Repeatedly setting the cruise speed can increase fuel consumption and lead to dangerous accidents. Cruise control is also unsuitable for use on undulating mountain roads. 2. Intermittent Usage: Furthermore, during long-distance driving, it is best to use cruise control intermittently. Over-reliance on cruise control can easily lead to a lack of concentration. Intermittent use of cruise control can help prevent fatigue driving, and of course, remember to open the windows for ventilation to maintain focus. Therefore, cruise control must be used on appropriate road sections and at suitable speeds.
4
1
Share

How to Open the Front Hood of a Leiling Car?

The steps to open the front hood of a Leiling car: 1. Locate the hood release lever near the left door pillar inside the cabin; 2. Pull the hood release lever until you hear a click, and you'll notice the front hood slightly pops up with about a 1cm gap; 3. Lift the front hood with one hand while using the other hand to reach under the grille and pull the secondary release latch; 4. Push up the latch and prop up the hood support rod. The Leiling is a compact sedan produced by GAC Toyota, featuring a 4-door, 5-seat configuration. Its dimensions are 4640mm in length, 1780mm in width, and 1455mm in height, with a wheelbase of 2700mm. The suspension system combines MacPherson strut front suspension with an E-type multi-link rear suspension.
11
4
Share

How to Reset the Maintenance Light on a BMW X4?

BMW X4 maintenance reset steps: 1. Turn on the ignition without starting the vehicle; 2. Press the button on the left side of the instrument cluster, hold the button and switch the ignition to the on position; 3. After holding the button for 5 seconds, the maintenance status will be displayed, including the maintenance cycle, oil change service, inspection service, and remaining mileage; 4. Hold the button for another 5 seconds to enter the reset mode. During the flashing process, first release the button, press it again, and then release it to reset the mileage maintenance. The BMW X4 is a midsize SUV with a body structure of a 5-door, 5-seat crossover. The vehicle dimensions are 4763mm in length, 1926mm in width, and 1632mm in height, with a wheelbase of 2864mm. The suspension system features a double-joint spring strut front axle and a five-link rear suspension combination.
3
0
Share

What Are the Reasons for a Motorcycle Failing to Start?

The reasons for a motorcycle failing to start are as follows: Fuel system failure: Mainly caused by issues such as the fuel switch (not supplying fuel), fuel filter (clogged), carburetor (not supplying fuel or the mixture being too rich), or bent fuel pipes. Electrical circuit failure: Short circuits in the vehicle's electrical components (e.g., ignition switch, ignition coil, ignition module, or magneto failure) or open circuits caused by loose wiring harness connectors. Air pressure failure: Insufficient cylinder compression, improper air intake resistance of the air filter element, or engine intake and exhaust faults, among others. Weather conditions: Typically, it is due to excessively cold weather, which reduces the performance of the engine oil, leading to insufficient cylinder pressure.
12
2
Share

Where was the first car in China produced?

Changchun First Automobile Works assembled the first Jiefang brand truck. Below are specific details about China's first automobile: 1. History: The first batch of Jiefang trucks rolling off the production line were called CA10 models. Based on the Soviet ZIS-150 design, these vehicles weighed 3,900 kg, equipped with a 90-horsepower four-stroke six-cylinder engine, with a load capacity of 4 tons and a maximum speed of 65 km/h. After improvements, they became more suitable for China's road conditions and large-scale construction needs. 2. Process: The first batch of Jiefang trucks participated in the 1956 National Day parade, with some later exhibited at Tiananmen Square, attracting countless citizens eager to witness the debut of domestically produced vehicles. 3. Significance: The birth of the first Jiefang truck embodied the hard work of all builders and reflected the direct leadership and high-level attention from the Party Central Committee. The naming process of China's first automotive brand "Jiefang" particularly demonstrated this point.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.