What does motorcycle CVT mean?

1 Answers
Perry
07/25/25 1:38am
Motorcycle CVT (Continuously Variable Transmission) has no gears and uses an automatic centrifugal clutch. It changes the transmission ratio by adjusting the diameters of the front and rear pulleys. This type of transmission has no fixed steps and is entirely controlled by throttle, engine speed, and pulley diameter changes. Definition of stepped transmission: Automatic disengagement still means the clutch is in an automatic disengaged state, while stepped transmission incorporates gear shifting. This combination significantly improves working efficiency compared to scooter transmission forms, enhancing power while reducing fuel consumption, though it still has drawbacks. Definition of multi-speed transmission: This type of transmission still consists of a clutch and gear shifting, except that the clutch is no longer automatically disengaged but manually disengaged instead.
Was this review help?
8
4
Share
More Forum Discussions

Can National V Vehicles Be Licensed?

If the city has already implemented the National VI emission standards, then new National V vehicles cannot be licensed. The following is an introduction to the National VI emission standards: The National VI Motor Vehicle Pollutant Emission Standards are established to prevent environmental pollution caused by exhaust emissions from compression-ignition and gas-fueled spark-ignition engine vehicles, protect the ecological environment, and safeguard human health. Extended content: 1. The difference between National VI and National V vehicles lies in their emission standards: The National VI emission standards are more stringent than the National V standards, with an increase of 40% to 50% over National V, making them the strictest emission standards currently. 2. The National VI emission standards are divided into two phases: National VIa and National VIb. National VIa is a transitional phase based on the National V standards with further improvements, while National VIb represents the true National VI standard.
9
4
Share

How to Change Engine Oil by Yourself?

The method to change engine oil by yourself is: 1. First, purchase the recommended engine oil type as per the manual. Before changing, let the engine run for a while to warm up the oil, which helps in completely draining the old oil. 2. Turn off the engine, open the oil filler cap, remove the drain plug at the oil pan to drain all the oil. 3. Tighten the drain plug. Replace the oil filter, then you can add new oil. Fill to the appropriate level on the oil dipstick. Additional information: 1. Engine oil, also known as engine lubricant, serves to lubricate and reduce friction, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption for the engine. 2. Engine oil consists of base oil and additives. The base oil is the main component of the lubricant, determining its basic properties, while additives compensate for and improve the shortcomings of the base oil, imparting new characteristics, making them an essential part of the lubricant.
3
1
Share

What is the difference between a central circle and a grid line?

The differences between a central circle and a grid line are as follows: 1. Difference: A grid line is a large yellow grid area where long-term parking is not allowed; a central circle is a small white circular or square (diamond-shaped) area in the middle of an intersection, generally assisting vehicles in turning, and controlling the vehicle's position within the central circle without crossing the line. 2. Road traffic markings: (1) Lines, solid or dashed lines marked on the road surface, curbs, or vertical surfaces; (2) Character markings, text, numbers, and various graphic symbols marked on the road surface; (3) Raised pavement markers, fixed on the road surface, serving as marking blocks, used on highways or other roads to mark centerlines, lane dividers, edge lines, and also to mark curves, entrance/exit ramps, guide lines, road narrowing, and road obstacles.
1
4
Share

What Causes the Front Wheels to Squeak When Turning?

Abnormal noises from tires during turns commonly occur in front wheels, primarily due to the following reasons: 1. Specific causes: Excessive accumulation of foreign objects on the left and right front wheel mudguards or sound insulation pads. When the car turns, the tires interfere with these objects, producing abnormal sounds. Long-term buildup of mud and debris on mudguards causes interference with tires. The noise disappears after cleaning. Loose fastening screws on mudguards or sound insulation pads cause them to lift, leading to interference and friction with front wheels during turns, resulting in abnormal sounds. It is necessary to inspect the fastening condition of mudguards and sound insulation pads and eliminate factors such as looseness or lifting. 2. Precautions: Tire noise is a very serious issue. The source of the noise should be promptly identified and resolved as soon as possible. Otherwise, it may cause abnormal tire wear and affect driving safety.
15
2
Share

What is the name of the window film that cannot be seen through from the outside?

The window film that cannot be seen through from the outside is called one-way mirror window film. Here are the relevant details: 1. Definition of one-way mirror film: One-way mirror film (also known as one-way film, mirror film, etc.) refers to a film attached to glass that gives the glass a high reflectivity to visible light. One-way mirror film can achieve an effect where, when the outside is brighter than the inside, the one-way mirror glass resembles an ordinary mirror, with the inside scene not visible from the outside, but the outdoor scene visible from the inside. Nowadays, one-way mirror film is commonly used in movies. 2. Advantages of window film: a. Heat insulation and temperature retention; b. Safety and explosion-proof; c. UV protection; d. Anti-glare; e. Easily creates a private space; f. Enhances visual effects; g. High-temperature resistance and fireproofing.
1
4
Share

Can an out-of-province driver's license be renewed in Beijing?

Renewing a driver's license in a different location is possible. The methods for renewing a driver's license in a different location are as follows: Method 1: Apply for renewal at the local vehicle management office in person. The driver should bring the required materials to the vehicle management office where the driver's license was originally issued. The office will process the renewal within one working day upon approval. Method 2: Apply for renewal online via the "Traffic Management 12123" app. Specific steps: Download the "Traffic Management 12123" app, then select Service Center — License Renewal Service — Fill in the information (follow the prompts). The new license is usually delivered by mail. Method 3: Visit a "Police-Medical-Post" service point at a postal office to complete the renewal process, which takes about half an hour from registration to medical examination and new license production. However, this service is currently only available in a few cities, such as Hangzhou. Required materials for renewal include: Two copies of ID card, two recent 1-inch color photos without hats, original ID card, original driver's license, and a medical examination certificate from a county-level or above hospital (free medical examination is also available at the vehicle management office).
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.