What Does Li Auto's Lifetime Warranty Cover?

Why is the rearview mirror adjustment button not working?

The reasons why the rearview mirror adjustment button is not working are as follows: 1. Poor button contact: This means the adjustment button fails to function in the up, down, left, or right directions. In this case, first check the switch. Generally, cleaning it will restore normal operation. Since disassembling the entire control panel is difficult, it is recommended to go directly to an auto repair shop or 4S store and let professionals clean it. 2. Misalignment of the white screw inside the mirror: The phenomenon is that when adjusting, the motor has working sounds and a working state, but the adjustment fails. Solution: Simply reset the white screw. 3. Damaged motor gears or wiring harness issues: In this case, you can only go to a 4S store or auto repair shop and let professionals inspect it first.

18

4

Share

What Causes Weak Trunk Hydraulic Rods?

Weak trunk hydraulics may be due to ineffective support rods in the car's trunk. Below are specific methods for opening a car trunk: 1. Remote Key from Outside: The most common way to open the trunk from outside is via the remote key. Simply press the trunk icon button (usually showing a raised car rear) on the key fob to release the trunk. Some models without a dedicated trunk button can be opened by pressing the general unlock key. 2. Interior Control Switch: Interior controls include button-type and lever-type mechanisms. Button locations vary by manufacturer and model, typically found on the steering wheel's left side or dashboard area. For example, the Sagitar's trunk button is usually on the door panel. Some models use a lever instead of a button, generally positioned below the driver's seat left side or steering wheel's lower left area.

17

0

Share

Where is the OBD port on the Peugeot 301?

The OBD port of the Peugeot 301 is located at the lower left side of the steering wheel, and you need to remove the interior trim panel on the lower left side of the steering wheel to see it. Here is the relevant introduction: 1. How OBD works: The OBD system continuously monitors whether the vehicle's exhaust exceeds the standard from the engine's operating conditions. Once it exceeds the standard, it will immediately issue a warning. When the system fails, the fault (MIL) light or the Check-Engine warning light will come on, and the Powertrain Control Module (PCM) will store the fault information in the memory. The fault code can be read from the PCM through a certain procedure. 2. OBD interface: It is generally a 16-pin female interface, and the interface is trapezoidal. Some models have a protective cover on the OBD port. The common OBD interfaces are black, white or blue.

19

0

Share

Is it necessary to turn on the AC when defogging while driving in summer rain?

It is not always necessary to turn on the AC when defogging while driving in summer rain, because under normal circumstances, both the cold air and warm air in the car can help eliminate fog. The formation of fog is caused by moisture and temperature. After turning on the front windshield defogging function, it will gradually dry out, but this process takes a relatively long time. Correct usage of the car's A/C button: Automatic air conditioning: You need to set the temperature in advance, and then it will automatically turn the A/C switch on or off based on the light sensor and temperature sensor to maintain a constant temperature inside the car, ensuring comfort. Manual air conditioning: You need to manually adjust the air vent’s airflow and temperature, as well as manually press the A/C switch button. Generally, it is difficult to maintain a constant temperature inside the car, so frequent manual adjustments are required to ensure comfort.

3

2

Share

What Causes the BYD Engine Warning Light to Illuminate?

Sensor malfunctions, vehicle maintenance issues, fuel quality problems, poor combustion of the air-fuel mixture, engine intake issues, turbocharging problems, exhaust system faults, and anti-theft system failures are the primary reasons for the engine warning light to illuminate. Additionally, during vehicle startup, the car performs a self-diagnostic check on the engine system. Normally, the warning light should turn off after the self-check is completed. If it remains lit for an extended period, it is advisable to promptly visit a service center for professional assistance to diagnose and eliminate potential safety hazards. Below is a detailed explanation of each potential fault: Sensor Issues: Sensors include those for coolant temperature, crankshaft position, air flow, intake air temperature, and oxygen levels. When these sensors are damaged, have poor connections, or experience signal interruptions, the vehicle's ECU cannot accurately obtain engine data, triggering the engine warning light. In such cases, it is essential to seek professional inspection at a service center to promptly address safety concerns. Maintenance Issues: Poor engine maintenance is one of the most common causes of the engine warning light illuminating. Vehicles have specific maintenance schedules, and failure to adhere to them, combined with poor driving habits, can increase the engine's operational burden, eventually causing the warning light to activate as a reminder of a fault. Fuel Quality Issues: This refers to both fuel and engine oil. Vehicles typically require fuel of a specific grade, and engine oil can be semi-synthetic or fully synthetic. Manufacturers usually recommend the appropriate fuel grade and oil type. If the owner fails to use the recommended specifications, prolonged use can lead to engine wear, triggering the warning light. Always use the correct fuel grade and suitable engine oil as specified for the vehicle. Poor Combustion of Air-Fuel Mixture: Faulty spark plugs, ignition coils, fuel pumps, or clogged fuel lines can result in poor combustion of the air-fuel mixture. This can lead to engine carbon buildup or knocking, which the oxygen sensors detect and report to the ECU, causing the warning light to illuminate as a warning. Intake Issues: Proper air intake is crucial for engine combustion. The air filter plays a vital role in this process. If the air filter is dirty or not cleaned regularly, it can obstruct airflow, potentially leading to blockages and, in severe cases, triggering the engine warning light. Turbocharging Issues: Problems with the intake boost pipes or turbocharger can also cause the engine warning light to illuminate. The most common issue is turbocharger damage, often accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Exhaust System Issues: Faults in the rear oxygen sensor, catalytic converter, exhaust camshaft, or bearings can trigger the warning light. The catalytic converter is particularly prone to failure due to factors such as the use of leaded gasoline, lead- or silicon-based oil additives, physical damage, or fuel system malfunctions. Anti-Theft System: If the electronic anti-theft system malfunctions or if there is a mismatch between the anti-theft controller and the engine ECU, the engine may not operate correctly, and the warning light may illuminate. Solutions for an Illuminated Engine Warning Light: If the engine warning light is on and the vehicle cannot start, this may indicate a fuel pump or ignition component failure. It is recommended to call for assistance immediately. If the warning light is on but the vehicle is drivable, yet exhibits severe shaking or loss of acceleration, pull over safely and call for roadside assistance. If the warning light is on but no abnormalities are observed while driving, it may indicate a faulty sensor. In this case, the vehicle can be driven cautiously at low speeds, but it is best to visit a repair shop as soon as possible to address the issue.

1

5

Share

How to Replace the Key Battery for DS6?

Method to replace the key battery for DS6: 1. Press the button on the electronic key to release the mechanical key; 2. Insert a screwdriver into the small notch at the top covered by the mechanical key, gently pry upwards, and the electronic key will separate; 3. At this point, the battery will be visible. Remove the old battery and replace it with a new one; 4. Snap the two parts back together, press the edges to restore the clips to their original position; 5. Insert the mechanical key back into the electronic key to lock it. In terms of body dimensions, the DS6 measures 4553 mm in length, 1858 mm in width, and 1600 mm in height, with a wheelbase of 2732 mm. For safety configurations, the DS6 comes standard with ABS, EBD, EBA, ASR, ESP, front and side airbags, side curtain airbags, tire pressure monitoring, and other practical features.

3

0

Share

What Does Li Auto's Lifetime Warranty Cover?

Why is the rearview mirror adjustment button not working?

What Causes Weak Trunk Hydraulic Rods?

Where is the OBD port on the Peugeot 301?

Is it necessary to turn on the AC when defogging while driving in summer rain?

What Causes the BYD Engine Warning Light to Illuminate?

How to Replace the Key Battery for DS6?

What is the situation when the Envision navigation has no network?

What does 'used car transfer included' mean?

What tires are used on the Hongqi H5?

How to Deal with White Scratches on a Car?