What does it mean when Volkswagen displays 'pressure loss detected'?

1 Answers
Clay
07/30/25 1:43am
When the tire pressure monitoring system detects insufficient pressure in one or more of the vehicle's tires, it will illuminate a warning light on the dashboard along with a text alert to notify the driver. At this point, the driver should promptly adjust the tire pressure to the standard value and reset the tire pressure monitoring system to clear the warning light. Here are some common issues related to the tire pressure warning light: 1. The tire pressure monitoring system warning light remains on: If the warning light stays on after adjusting the tire pressure and performing a reset operation, it may indicate a malfunction in the tire pressure monitoring system. A common fault is low battery in the sensor electronics. 2. Warning light illuminates when heavily loaded: This occurs because the vehicle's load is too high, causing the tire pressure to exceed the preset upper limit.
Was this review help?
15
0
Share
More Forum Discussions

What does TPMS malfunction mean?

TPMS malfunction refers to a Tire Pressure Monitoring System failure. The illumination of the TPMS warning light alerts the driver to abnormal tire pressure, which may be caused by low pressure in one or more tires. When this warning light appears, the tire pressure should be checked as soon as possible. If the TPMS warning light comes on while driving, remain calm, do not panic, immediately reduce speed, avoid sharp steering and sudden braking, and then check the tire pressure. The hazards of low tire pressure include: 1. Increased friction coefficient with the road surface: leading to higher fuel consumption; 2. Causes the steering wheel to feel heavy: resulting in factors such as veering that are detrimental to driving safety; 3. Increases the movement of various parts of the tire: excessive rolling causes abnormal heat generation in the tire; 4. Reduces the functionality of the cords and rubber: leading to delamination or cord breakage, and excessive friction with the rim causing damage to the bead area and abnormal wear; 5. Multiplies the friction between the tire and the ground: causing a sharp rise in tire temperature, softening the tire, and drastically reducing its strength. High-speed driving under these conditions may lead to a tire blowout; 6. Low tire pressure increases tire body deformation: the tire sidewalls are prone to cracking, and flexing movements occur, leading to excessive heat generation, accelerating rubber aging, fatigue in the cord layers, and cord breakage, while also increasing the tire's contact area with the ground and accelerating shoulder wear.
11
1
Share

What Causes Wheel Spin When Accelerating Hard from a Standstill?

The reasons for wheel spin when accelerating hard from a standstill are: 1. Insufficient tire contact area; 2. Inadequate friction; 3. Excessive power delivery. Methods to handle wheel spin include: 1. For rear-wheel-drive vehicles: Release the accelerator pedal, steer the front wheels straight, then gently press the accelerator to resume driving in the correct direction; 2. For front-wheel-drive vehicles: Gradually release the accelerator pedal while steering in the desired direction, straighten the steering wheel, and accelerate gently. The method for starting a manual transmission car is: 1. Insert the key and turn the ignition switch to start the engine; 2. Depress the clutch pedal and shift into first gear; 3. Release the handbrake, slowly lift the clutch pedal, and apply throttle.
15
0
Share

What Causes Vehicle Body Shaking at Low Speeds?

The reasons for vehicle body shaking at low speeds are: 1. Throttle blockage, carbon buildup, or abnormal opening; 2. Carbon buildup or blockage in the fuel injector; 3. Spark plug burning or damage; 4. Use of low-quality gasoline, leading to fuel pump blockage; 5. Incomplete combustion of the air-fuel mixture in the cylinder. The methods to address vehicle body shaking at low speeds are: 1. Read fault codes or data streams to eliminate sensor faults; 2. Check if the exhaust gas recirculation (EGR) valve has issues; 3. Inspect spark plugs, high-voltage wires, ignition coils, fuel injectors, timing marks, fuel pump pressure, and cylinder pressure; 4. Check if the idle speed control motor has problems, and clean the throttle and idle speed control motor.
4
3
Share

Does the Volkswagen Lavida need underbody armor?

Volkswagen Lavida does not require underbody armor. Underbody armor can provide rust and corrosion protection, safeguard the chassis during rainy or snowy weather, and reduce noise. The Volkswagen Lavida is a compact 4-door, 5-seater sedan with body dimensions of 4670mm in length, 1806mm in width, and 1474mm in height, with a wheelbase of 2688mm. It is equipped with a 1.4T turbocharged engine and a 7-speed dual-clutch transmission, delivering a maximum power of 110 kW and a maximum torque of 250 Nm. The drivetrain is front-wheel drive, with a front suspension using MacPherson strut independent suspension and a rear suspension employing a torsion beam non-independent suspension.
18
0
Share

What Causes CVT Shaking at Low Speeds?

CVT jerking at low speeds may be due to the transmission fluid inside the CVT not having reached normal operating temperature, or it could be caused by the CVT transmission fluid not being replaced for an extended period. How CVT Transmission Works: The transmission internally consists of only two pulleys and a steel belt. The steel belt of this transmission can move on the pulleys, allowing the transmission to vary speed and torque. Advantages of CVT Transmission: The advantages of CVT transmission include simple structure, compact size, fewer components, low manufacturing cost, lightweight, and smooth shifting.
16
5
Share

Does Car Air Conditioning Refrigerant Recharge Require Vacuuming?

Car air conditioning refrigerant recharge requires vacuuming. The steps for refrigerant recharge are: 1. System vacuuming, close the manual valves on the pressure gauge and the high and low pressure manual valves; 2. Connect one end of the hose to the injection valve connector of the refrigerant tank; 3. Open the refrigerant tank, loosen the nut of the pressure gauge hose, allow some gas to escape, then close it; 4. Open the high-pressure side valve and invert the tank; 5. Inject the specified amount of liquid refrigerant, then close the refrigerant injection valve and the high-pressure manual valve. Car air conditioning is used to adjust and control the temperature, humidity, air cleanliness, and air flow inside the car compartment to an optimal state. Its components include the refrigeration system, heating system, air purification device, and control system.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.