What does it mean when the front bumper of a car is not aligned with the pole line?

1 Answers
JaylaDella
07/29/25 8:53pm
The meaning of the front bumper of a car not being aligned with the pole line is that the owner's car bumper is not parked on the designated parking line as required, but is parked too far from the parking line, and if the distance does not exceed 50 centimeters, 20 points will be deducted. The introduction of the fixed-point parking bumper not reaching the yellow line is as follows: Introduction 1: After the vehicle stops, if the front bumper is not aligned with the pole line and exceeds 50 centimeters either forward or backward, it is considered a failure. Introduction 2: After the vehicle stops, if the front bumper is not aligned with the pole line but does not exceed 50 centimeters either forward or backward, 20 points will be deducted. Introduction 3: After the vehicle stops, if the body is more than 30 centimeters away from the roadside line, 20 points will be deducted. Introduction 4: After the vehicle stops, if the wheels run over the outer yellow line, it is considered a failure, and if they run over the inner white line, 10 points will be deducted. Introduction 5: If the car stalls once, 10 points will be deducted, and if it rolls back 30 centimeters, it is considered a failure.
Was this review help?
5
2
Share
More Forum Discussions

What is the reason for no air coming out from the driver's side of the car air conditioner?

No air coming out from the driver's side of the car air conditioner may be due to damage or failure to open the air duct separator valve, or incorrect air outlet mode settings. Below is more information about car air conditioners: 1. Cooling principle: When the car air conditioner is cooling, the compressor clutch engages, causing the engine to drive the compressor. The compressor continuously compresses the refrigerant and delivers it to the evaporator. Inside the evaporator, the refrigerant expands and absorbs heat, cooling the evaporator which in turn cools the air blown by the blower. 2. Heating principle: When the car air conditioner is heating, high-temperature coolant from the engine passes through the heater core. At this time, the air blown by the blower also passes through the heater core, allowing warm air to be blown out from the air conditioner vents.
8
5
Share

How Often Should You Replace Your Car's Air Filter?

It is recommended to replace the air filter every 1-2 years or every 10,000 kilometers. Below is a detailed introduction to car air filters: 1. Application Scope: An air filter is a type of filter primarily used for air filtration in engineering vehicles, cars, agricultural vehicles, laboratories, sterile operating rooms, and various precision operation rooms. 2. Impact of No Filtration: When the engine is running, it needs to intake a large amount of air. If the air is not filtered, the suspended dust in the air can be drawn into the cylinders, accelerating the wear of the piston group and cylinders. Larger particles entering between the piston and cylinder can cause severe "cylinder scoring," especially in dry and sandy working environments. 3. Function: The air filter is installed in front of the carburetor or intake pipe to filter out dust and sand particles from the air, ensuring that sufficient and clean air enters the cylinders.
1
0
Share

What is the difference between fully synthetic oil and semi-synthetic oil?

Synthetic oil and semi-synthetic oil differ in the following aspects: 1. Base oil composition: Fully synthetic oil is blended from Group III, IV, and V base oils, while semi-synthetic oil uses Group III base oil. 2. Replacement intervals: Fully synthetic oil has a service life of one year or 10,000 kilometers, whereas semi-synthetic oil requires replacement every six months or 7,500 kilometers. Engine oil, also known as motor lubricant, consists of base oil and additives. The base oil is the primary component of lubricating oil, determining its fundamental properties, while additives compensate for and enhance the performance limitations of the base oil. Its functions include: 1. Reducing friction and high temperatures; 2. Cooling and temperature reduction; 3. Cleaning and purification; 4. Shock absorption and cushioning; 5. Rust and corrosion prevention.
2
0
Share

Where is the best place to connect the power cable of a dash cam?

The power supply for a dash cam is generally connected to the cigarette lighter socket, which is the simplest and most convenient setup. Another option is to connect it to the ACC power in the fuse box, though this method is more complicated. Dash cams usually come with built-in and external power interfaces. The built-in power is typically a lithium battery, while the external power is usually supplied through the cigarette lighter. Relevant information about dash cams is as follows: 1. Introduction: A dash cam is a device that records images, sounds, and other related information during vehicle travel. 2. Function: After installing a dash cam, it can record the entire driving process's video images and sounds, providing evidence for traffic accidents.
11
3
Share

How often should the transmission fluid of the Changan Alsvin V7 be changed?

The transmission fluid of the Changan Alsvin V7 should be changed approximately every 60,000 kilometers. Required amount of transmission fluid for Changan Alsvin V7: For the manual transmission of the Changan Alsvin V7, 2 liters of transmission fluid are sufficient. Generally, some vehicles require 3 bottles, while others may need 4 bottles. There are markings on the dipstick; just add according to the markings. Introduction to transmission fluid: Transmission fluid, also known as gear oil, is used inside the transmission. It is a cleaning product that can clean the transmission system. Transmission fluid is divided into automatic transmission fluid (ATF) and manual transmission fluid. ATF is specifically designed for automatic transmissions, while manual transmission fluid is for manual transmissions. The quality of the transmission fluid directly affects the performance of the transmission.
15
0
Share

What does simulated class hours mean?

Simulated class hours refer to the mandatory minimum number of training hours a student must complete before being eligible to take the driving test. Below is a detailed explanation of how to accumulate hours for Subject 2: 1. Clocking in for hours: The student's ID card is used to clock in directly on the device, but this requires the student to bring their ID card every time, which can be inconvenient if forgotten. 2. Unified management by the instructor: The driving school issues each student a training hour card, which is the method adopted by most driving schools. Students clock in when they start practicing and clock out when they finish, recording the hours. The advantage of this method is that all students' training hour cards are managed uniformly by the instructor, allowing them to practice and clock in at any time.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.