What does it mean when the car displays 'Service Vehicle Soon'?

1 Answers
DiMaya
07/29/25 8:18pm
Service Vehicle Soon indicates that there is a fault with the vehicle, requiring the owner to promptly inspect and repair it to avoid affecting the driving experience. This warning may also be triggered by overdue vehicle maintenance or engine issues, necessitating a check-up at a repair shop. Here is some relevant information: 1. Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the vehicle to prevent malfunctions. 2. Car maintenance mainly includes the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, and more.
Was this review help?
9
4
Share
More Forum Discussions

How many liters of engine oil should be added to the Buick Excelle?

The Buick Excelle requires approximately 4L of engine oil during an oil change. After adding the oil, you should check the oil dipstick to confirm the exact amount. Oil dipstick scale standards: To determine whether the amount of oil added is sufficient, check the oil dipstick after adding the oil. The dipstick has two marks: a maximum and a minimum. The correct oil level should not exceed the maximum mark or fall below the minimum mark; it should be between these two marks. How to check the oil level: After adding the oil, start the vehicle and then turn it off. Wait for 3 minutes before checking the oil level. This is because the oil filter is also replaced during an oil change, and the new filter initially contains no oil. After starting the vehicle, oil flows into the filter. Waiting 3 minutes allows the oil to settle back into the oil pan, ensuring a more accurate reading. Do not check the oil level on a slope, as the tilted position of the vehicle will cause the oil in the pan to tilt as well, leading to an inaccurate reading. Always ensure the dipstick is held perpendicular to the ground for the most accurate measurement.
9
5
Share

Where to Add Water to the X-Trail's Radiator?

The X-Trail's radiator is located in the engine compartment, next to the windshield washer fluid reservoir. The car radiator generally refers to the car's cooling system radiator, which is part of the engine's liquid cooling system. The radiator in the engine's liquid cooling system consists of three parts: the inlet chamber, outlet chamber, main plate, and radiator core. The method for adding water and coolant to the X-Trail's radiator is as follows: 1. With the car engine cooled down, unscrew the radiator cap, open the radiator drain valve, and drain the coolant. 2. Insert a rubber hose connected to a tap into the radiator filler port, turn on the tap, and let tap water continuously flow through the engine cooling system. During this flushing operation, keep the engine idling and continue until clear water comes out of the radiator. 3. Turn off the tap, wait for the cooling system to drain completely, then close the radiator drain valve. 4. Add coolant from the radiator filler port until the radiator is full. Unscrew the reservoir cap, add coolant up to the 'Max' mark, being careful not to exceed it. 5. Replace and tighten the radiator cap and reservoir cap. 6. Start the engine and let it idle for 2-3 minutes, then unscrew the radiator cap. At this point, as some air has been expelled from the cooling system, the coolant level will drop. Add more coolant until it reaches the 'Max' mark. 7. Securely fasten the radiator cap.
5
5
Share

What Causes the Half Shaft Oil Seal of the Prado to Leak?

The reason for the half shaft oil seal leakage in the Prado is excessive oil filling in the drive axle reducer, causing the oil level to exceed the normal height. Specific causes of half shaft oil seal leakage: Deterioration and aging of the oil seal leading to reduced sealing effectiveness. Improper installation of the oil seal, resulting in gaps. Blockage of the drive axle reducer vent hole; during driving, the oil temperature rises, pressure increases, and oil is forced out, damaging the oil seal. Poor quality or incorrect dimensions of the half shaft oil seal, or loose installation between the oil seal and the half shaft sleeve. Loose wheel hub bearings or drive axle reducer bearings causing the half shaft to shake up and down. Wear of the half shaft journal leading to poor sealing. Hazards of half shaft oil seal leakage: Oil leakage from the half shaft oil seal reduces the amount of lubricating oil in the drive axle, affecting normal lubrication and accelerating wear of components, leading to premature failure. Oil leakage from the half shaft oil seal allows lubricating oil to flow into the wheel-side reducer, raising the oil level in the wheel-side reducer, which can damage the oil seal and flow into the brake drum, resulting in poor braking performance and posing a safety risk.
12
5
Share

Where is the starter relay located in the Buick Excelle?

The starter relay of the Buick Excelle model is located in the engine compartment fuse box, at the connection point between the engine and the transmission. Introduction to relays: A relay is an electrical control device that causes a predetermined step change in the controlled quantity in the electrical output circuit when the change in the input quantity (excitation quantity) reaches the specified requirements. Function of relays: Relays establish an interactive relationship between the control system (also known as the input circuit) and the controlled system (also known as the output circuit). They are commonly used in automated control circuits, essentially acting as an "automatic switch" that uses a small current to control the operation of a larger current. Therefore, relays play roles in automatic regulation, safety protection, and circuit switching within electrical circuits.
20
0
Share

What does a white parking space line mean?

White parking space lines indicate that this is a paid parking space. In areas with white markings, you need to check roadside signs to determine if parking is actually allowed, as not all white lines on the roadside denote parking spaces. Even in paid parking zones, you cannot park at any time and must follow the instructions on roadside signs. More information about parking space lines is as follows: 1. Blue parking space lines: Indicate that this is a free parking space. However, it's important to note that there are two situations where you might be penalized: (1) Parking for more than a day or longer, as blue parking spaces prohibit vehicles from being maliciously occupied for extended periods; there are also blue dashed parking spaces that specify time-limited parking, and exceeding the time limit should be avoided. (2) Some blue-lined parking spaces may have arrows indicating the parking direction, which should also be noted. 2. Yellow parking space lines: Indicate that this is a dedicated parking space. Dedicated parking spaces are usually reserved for special vehicles, such as fire trucks. If the yellow line is a solid single line, it means "No Parking," and areas marked with yellow single solid lines or yellow curbs are not allowed for parking. If the yellow line is dashed, it means temporary parking is allowed, but long-term parking is not permitted.
11
3
Share

What Level Does SAIC's Blue Core Engine Belong To?

SAIC's Blue Core engine has been recognized as one of the "China Core" Top 10 Engines of the Year, with relatively reliable engine quality and durability. The MGE series engines are independently developed by SAIC, primarily focusing on SAIC's inline all-aluminum four-cylinder engines. The engine displacements mainly include 1.8T, 2.0T, and 2.0L. The power ranges from 120 kW to 162 kW, and the torque ranges from 200 Nm to 350 Nm. In terms of engine lifespan, the development of each engine takes into account the issue of service life. Generally, the service life of these engines can reach up to 15 years or 400,000 kilometers. SAIC's "Blue Core" 30T-MGE-Trophy high-performance turbocharged engine is built with aerospace-grade all-aluminum materials, reducing overall weight to enhance vehicle power performance while improving fuel efficiency. The engine features in-cylinder direct fuel injection technology, which ensures more uniform gasoline atomization, improves combustion efficiency, and reduces wall-wetting phenomena. The reduction in wall-wetting phenomena helps minimize carbon buildup. Additionally, the engine employs a variable displacement oil pump, which can meet the oil demands under different operating conditions, allowing the oil pump to operate at minimal power consumption, reducing friction losses, and achieving a 2% reduction in fuel consumption under NEDC conditions.
5
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.