What does it mean when the brake light comes on while driving?

1 Answers
DelDaniela
07/29/25 11:43pm
When the brake light comes on while driving, it may indicate a fault in the braking system. However, there could also be other reasons for the brake light to illuminate. Braking system faults: If the brake warning light comes on while driving, remain calm and try to reduce your speed gradually. Then, pull over to a safe location as soon as possible to inspect the vehicle. Check if the brake fluid is low - if it is, look for possible leaks. Examine the wear level of the brake pads. Verify if the parking brake switch is properly released. It's recommended to use a diagnostic scanner for a quick and accurate identification of the fault, then systematically investigate the cause. Other causes: There are other factors that can trigger the brake system warning light, such as false alarms. When driving uphill or during hard braking, excessive slope or fluid agitation may cause the fluid level indicator to give false warnings. For such occasional alerts, simply adding an appropriate amount of brake fluid should suffice.
Was this review help?
14
1
Share
More Forum Discussions

What brand is the engine of the Changan CS55plus?

JL473ZQ7 is the engine model used in the Changan CS55plus, with a maximum horsepower of 188 hp, a maximum power of 138KW, a maximum power speed of 5500rpm, and a peak torque of 300N.m. The engine of the Changan CS55plus is a domestic engine, manufactured by a factory under Changan. For the daily maintenance of the Changan CS55plus engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, causing various problems for the engine. To avoid faults, oil should be changed regularly according to usage conditions, and the oil level should be kept moderate. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve and still bring dirt back to the lubrication area, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. When the amount is small, it remains suspended in the oil; when large, it precipitates from the oil, clogging filters and oil holes, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the normal operation of the engine but also extends the overall lifespan of the radiator and engine.
13
4
Share

What is the keyout indicator light?

keyout is the car key status indicator light. The reasons for the keyout indicator light to illuminate are as follows: 1. The smart key is out of range: The smart key is not inside the car or is too far away beyond the specified distance. When the keyout indicator light appears on the dashboard, it indicates that the smart key is not inside the car or is not within the effective range. 2. Low battery in the key: The key battery is low, causing the key signal to be too weak to be received. If the smart key is inside the car, it may be due to low battery, resulting in a weak signal that cannot be received. 3. Smart key system malfunction: There may be damage or a fault in the smart key system or wireless module.
6
5
Share

Does the High-Pressure Fuel Pump Need Replacement if It Makes Abnormal Noises?

If the fuel pump produces noises, it needs to be replaced with a new one. Below is relevant information about the fuel pump: 1. The fuel pump is a crucial component in the fuel supply system. Without the fuel pump, the engine's fuel supply would be compromised, affecting its normal operation. 2. The fuel pump is located inside the fuel tank. Some engines equipped with direct injection technology also have a high-pressure fuel pump in the engine compartment. The fuel pump draws gasoline from the fuel tank and supplies it at the required pressure. Most commonly encountered engines use either multi-point injection or direct injection.
6
2
Share

How to Fix Misaligned Rearview Mirror Gears?

Misaligned rearview mirror gears cannot be repaired and require replacement with a new folding gear set at a 4S shop. There are two main adjustment methods for rearview mirrors: 1. Exterior adjustment: This method involves manually adjusting the mirror frame or surface position while the vehicle is parked to achieve the desired viewing angle. 2. Interior adjustment: This allows drivers to adjust the rearview mirror while driving, providing convenient conditions for observing the rear view. The rearview mirror is a tool that enables drivers to directly obtain external information about the rear, side, and lower areas of the vehicle while seated in the driver's seat. It serves to facilitate driver operation, prevent traffic safety accidents, and ensure personal safety.
1
1
Share

How to Repair Rice Grain-Sized Pits on Windshield?

Windshield rice grain-sized pit repair steps are as follows: 1. Clean glass debris thoroughly: After drilling, remove all glass fragments from the pit as they may affect the repair result. 2. Inject repair fluid into the pit: Use repair tools to inject and pressurize the repair fluid into the pit until it fills completely. 3. Cure the repair fluid: Use a UV lamp to solidify the repair fluid. 4. Remove repair tools: Dismantle the tools and scrape off any residual repair fluid on the surface with a blade to complete the repair. While you can purchase tools to repair windshield rice grain-sized pits yourself, for better results, consider visiting a professional glass repair shop.
1
3
Share

What are the solutions for clutch judder?

Solutions for clutch judder are as follows: 1. Check for operational issues: Determine if there are operational problems. When the clutch is depressed and in a semi-engaged state, if the car's idle speed is unstable or the coordination between the accelerator pedal and the clutch is improper, it can cause engine judder. 2. Verify if the clutch disc was recently replaced: If the clutch disc was just replaced, this situation may occur. After the clutch disc, pressure plate, and flywheel have worn in for a period of time, it will return to normal. 3. Assess the car's performance: Some cars have unique performance characteristics, with clutch travel gaps that are either too small or too large. If not mastered skillfully, it may lead to clutch judder.
5
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.