What does it mean when BMW chassis functions are restricted?

What is the National V Standard Logo?

The logo for the National V standard is the letter 'v'. Below is a partial introduction to the National V standard: 1. Standard Overview: The National V standard is equivalent to the EU's Euro 5 standard, which has been implemented in the EU since 2009. It imposes stricter limits on vehicle emissions such as nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter. Each upgrade from National I to National IV reduces single-vehicle pollution by 30% to 50%. As of January 2013, the National V standard was still in the solicitation phase. 2. Implementation Time: The National V standard was implemented nationwide on January 1, 2017, as the fifth stage of the national vehicle emission standards. Cities like Beijing, Shanghai, Nanjing, and parts of Guangdong have already begun enforcing the National V standard. Starting April 1, 2016, all imported, sold, and registered light-duty gasoline vehicles, light-duty diesel passenger vehicles, and heavy-duty diesel vehicles in the Beijing-Tianjin-Hebei region must comply with the National V emission standard.

3

Share

Does exceeding 30 days without license plate registration after vehicle transfer have any impact?

Exceeding 30 days without license plate registration after vehicle transfer has no impact. You can directly go to the destination location to complete the registration. Measures for exceeding 30 days without license plate registration after vehicle transfer: Simply go to the destination location to complete the registration. Be careful on the way there since the temporary license plate has expired—it's best to transport the vehicle by tow truck. Consequences of exceeding the registration deadline: After the vehicle is transferred, the DMV has no record of it, so it will be considered a "black car." If caught driving it on the road, you will face penalty points, fines, and certain legal liabilities. If the owner needs to carry out other transfer registration procedures, some services may be restricted. For vehicles that meet the conditions for retaining license plates (e.g., desirable "good" plates), it is not possible to keep them if the vehicle is transferred but not registered. In the event of a traffic accident, these unregistered transferred vehicles may also involve the original owner.

3

5

Share

How to Replace the Air Conditioning Filter for Besturn B50?

The air conditioning filter for Besturn B50 is located inside the front storage compartment on the passenger side. Below are the steps for replacing the air conditioning filter: 1. Open the glove box, grasp both ends with both hands, and pull upwards firmly to remove the glove box. The blower is inside, and the air conditioning filter is located within; 2. Remove the cover plate to reveal the air conditioning filter; 3. Pull out the air conditioning filter; 4. Insert the new filter, paying attention to the correct orientation. Below is additional information about car filters: When driving with the air conditioning on, the car draws in external air into the cabin. However, the air contains various particles such as dust, pollen, soot, abrasive particles, ozone, odors, nitrogen oxides, sulfur dioxide, carbon dioxide, benzene, etc. Without an air conditioning filter to remove these particles, they can enter the cabin, not only contaminating the car's air conditioning system and reducing the cooling system's performance but also causing allergic reactions, lung damage, irritation from ozone exposure, and discomfort from odors, all of which can affect driving safety.

14

0

Share

Which button is for the heater in a car?

Different cars have the heater button in different locations. Taking Volkswagen as an example, the heater button in Volkswagen cars is the temperature adjustment knob, which is a round knob. Rotate the knob to the high-temperature indicator area to deliver warm air. When turning on the heater, make sure to turn off the A/C switch. Correct usage of the car heater: 1. When driving in the morning during winter, do not turn on the heater immediately after starting the engine, as the engine is still cold and cannot produce warm air. Instead, warm up the car first and wait until the engine or coolant temperature rises before turning on the heater. 2. Another important point is not to press the A/C button when using the heater in winter, as this controls the car's air conditioning compressor. The heater utilizes residual heat from the engine cooling system and does not require the compressor to produce warm air. Pressing the A/C button while using the heater will only increase fuel consumption. 3. Additionally, prolonged use of the heater can cause fogging on the windshield. The correct approach is to direct the warm air from the heater toward the windshield. In winter, prolonged use of the heater can also cause dizziness among passengers due to poor air circulation. Therefore, slightly open the windows to allow fresh air to circulate.

3

4

Share

How to Add Windshield Washer Fluid to Audi Q5

The windshield washer fluid reservoir in the Audi Q5 is located on the rear side of the engine hood pressure strut, with its cap marked by a washer symbol as shown in the illustration. The Audi Q5's windshield washer fluid capacity is 5 liters, and it should be refilled appropriately based on the remaining amount. Windshield washer fluid is a consumable item without a fixed refill cycle, depending on the frequency of the owner's usage. The steps for adding windshield washer fluid are as follows: 1. Turn on the wiper operation switch, and the windshield washer fluid will spray from below the front windshield. 2. Continue until the spray nozzles stop spraying, then open the windshield washer fluid filler cap and add a small amount of new washer fluid. 3. Turn on the wiper operation switch again to flush out the remaining old washer fluid. 4. When no more fluid sprays out from the nozzles the second time, add approximately 4 liters of washer fluid. Finally, securely close the washer fluid cap to complete the refilling process.

11

0

Share

How to Measure the Condition of a Car Battery?

Methods for measuring the condition of an electric car battery are as follows: 1. Judging by the external packaging of the battery: (1) Check if the outer packaging is damaged or has been opened. (2) Inspect the appearance of the battery itself for any scratches or rust on the positive and negative terminal connections. (3) Check if there is an anti-counterfeit label on the battery casing, whether the production date is relatively old, if the manufacturer's information and markings are complete, and if the writing is clear and legible. 2. Testing the battery's quality during a trial run—install the freshly charged battery onto the electric vehicle, start the vehicle's power, and suddenly accelerate while riding to observe the changes in the power gauge needle: (1) If the needle drops less than half a division during acceleration, the battery is judged to be new or in good condition. (2) If the needle drops by 1 or even 2 divisions during acceleration, the battery is judged to be old or of poor quality. (3) If the needle drops by 3 or even 4 divisions during acceleration, the battery is judged to be a refurbished product from a scrapped battery masquerading as new, indicating extremely poor quality.

18

1

Share

What does it mean when BMW chassis functions are restricted?

What is the National V Standard Logo?

Does exceeding 30 days without license plate registration after vehicle transfer have any impact?

How to Replace the Air Conditioning Filter for Besturn B50?

Which button is for the heater in a car?

How to Add Windshield Washer Fluid to Audi Q5

How to Measure the Condition of a Car Battery?

What causes the jerking when accelerating at low speeds in a GL8?

What does the pressure value on the tire indicate?

What engine does the BMW M4 use?

How to Tell if a Car Has Been Flooded?