···
Log in / Register

What does it mean when a car detects pressure loss?

4 Answers
Bailey
08/26/25 4:30am

When a car detects pressure loss, it could be due to two main reasons: either there is a leak in the car's tire, or the tire pressure is insufficient, leading to the pressure loss. When the tire pressure is too low, the following precautions should be taken while inflating the tires: 1. Safety during inflation: Always use a pressure gauge to check the pressure to avoid over-inflation, which could cause the tire to burst. 2. Inflate after cooling down: After stopping the vehicle, wait for the tires to cool down before inflating, as driving increases tire temperature, affecting the pressure. 3. Check the valve: If the valve and valve core are not properly aligned, or if there are any protrusions, depressions, or other defects, it may hinder inflation and pressure measurement. 4. Ensure clean air during inflation: The air being pumped into the tire should not contain moisture or oil, as this could damage the inner tube rubber.

Was this review help?
1
1
Share
LaAmara
09/08/25 5:53am

I remember last week while driving, the dashboard suddenly displayed a pressure loss warning, which made me nervous, so I quickly pulled over to check. I found a nail stuck in the right rear tire, causing the air pressure to gradually drop. Usually, this situation occurs when the tire is punctured by a foreign object or the valve core ages and leaks, especially after being parked on gravel roads for extended periods. I've also experienced days with significant temperature changes—high summer temperatures increase air pressure, while sudden drops in winter can cause the system to give false alarms. If not addressed promptly, the tire may wear unevenly or even blow out. I immediately used the spare tire as a temporary replacement and drove to a nearby repair shop to get the tire patched. Regularly checking tire pressure and the sealing performance of the wheel hubs greatly reduces such incidents. Now, before every long trip, I measure the pressure to ensure it's balanced. In short, recognizing pressure loss is a crucial warning—never ignore it. Safe driving is more important than anything else.

Was this review help?
17
2
Share
Expand All
AliceLynn
10/22/25 5:58am

Last time my car's system alerted me to pressure loss, which really delayed my commute. There are quite a few reasons for this, such as slow leaks due to tiny cracks from tire aging, or poor sealing caused by wheel rim deformation, which are common issues. False alarms can also be triggered if the sensor itself is dirty or malfunctioning. I checked the data, and if the pressure is more than 20% below the recommended level, it needs to be addressed. Otherwise, not only does fuel consumption skyrocket, affecting your wallet, but handling stability also decreases, increasing the risk of accidents. It's best to promptly use a pressure gauge to measure each tire's pressure and calibrate it within the recommended range. Continuing to drive after an alarm poses even greater risks, as the tire may overheat and deform, doubling repair costs. Developing a habit of checking tire pressure monthly is ideal, and extra attention should be paid to temperature changes in winter.

Was this review help?
6
5
Share
Expand All
RileyMarie
12/05/25 6:21am

When the car reports a pressure loss, the first thought is a leak in the tire. It could be caused by a nail puncture or aging valve leading to slow leakage, requiring a stop to check the tire pressure. The sensor might also malfunction and give a false alarm, but don't take it lightly. Quick response ensures safety, otherwise, driving becomes unstable and fuel consumption increases. Patching or replacing the tire can solve the issue, seek professional help if necessary.

Was this review help?
10
4
Share
Expand All
More Forum Discussions

How to Use Auto Start-Stop with a Manual Transmission?

When the auto start-stop system shuts off the engine, quickly shift to P gear, then you can release the brake pedal, and the engine will remain off. Here are some precautions: 1. Following traffic: In congested urban areas where frequent stop-and-go driving is required, the engine may vibrate slightly upon restarting, which can affect driving comfort. In such cases, you can temporarily disable the system by pressing the button with the capital letter 'A' surrounded by an incomplete circle. 2. Driving through water: As we all know, water entering the engine can cause severe damage. Since auto start-stop improves fuel economy by shutting off the engine, it's crucial to disable this feature when driving through deep water to prevent accidental engine shutdown, which could lead to water intake and engine damage.
19
2
Share

Can You Switch Between No Load, Medium Load, and Heavy Load While Driving?

Can You Switch Between No Load, Medium Load, and Heavy Load While Driving? Yes, you can switch between no load, medium load, and heavy load while driving. Below are the relevant introductions for no load, medium load, and heavy load: 1. Maximum RPM: In no-load mode, the engine will limit the maximum RPM, and the power output is only about 30% of the rated power. In medium-load mode, the output is about 60%, while in heavy-load mode, the full power can be output. 2. Electronic Control Unit: During no-load and heavy-load conditions, the electronic control unit will automatically limit the engine's torque and RPM based on different working conditions, ensuring the engine operates within the specified torque and RPM range, thereby reducing additional power consumption and achieving fuel savings for the entire vehicle.
17
0
Share

Is there a fee for an immediate retake of Subject 2?

An immediate retake of Subject 2 falls under the category of free retakes, so no fee is required. Below is relevant information about the Subject 2 examination: 1. Examination and Retake: Each subject of the driving test allows one examination attempt, with one free retake for those who fail. If the candidate does not attend the retake or fails the retake, the examination process ends, and the applicant must reschedule the examination. However, Subject 2 examinations must be rescheduled at least ten days later. 2. Re-registration after Five Failures: Within the validity period of the driving skill examination permit, the number of scheduled attempts for the Subject 2 road driving skill examination must not exceed five. If the fifth scheduled examination is still failed, the results of other previously passed subjects will be invalidated.
8
3
Share

How Much Fuel Should Be Added for Optimal Vehicle Performance?

Automobile fuel tank rated capacity should be controlled at 95% of the maximum safe capacity. Below is relevant information about vehicle refueling: 1. Maximum and reasonable fuel tank capacity: Generally, the capacity marked on ordinary fuel tanks is not the maximum volume but the maximum reasonable volume. For example, if a fuel tank is marked as 60L, it may actually hold around 70L when completely filled. Adding 60L represents a reasonable range that provides sufficient space for fuel expansion caused by temperature increases, thereby ensuring fuel tank safety during usage. 2. Safe fuel tank standards: Since refueling quantity cannot be determined based on the tank's rated capacity (automobile fuel tanks are containers, not measuring instruments), they cannot serve as verification of measurement accuracy. According to mandatory national standards, the rated capacity of automobile fuel tanks should be maintained at 95% of their maximum safe capacity.
17
3
Share

What are the issues if the car is not turned off while refueling?

Forgetting to turn off the engine while refueling generally does not cause adverse consequences to the vehicle, but it does pose certain potential hazards. The following are the risks of refueling without turning off the engine: 1. Electrical leakage leading to explosion: Not turning off the engine while refueling does not damage the vehicle's components. However, with the engine running at high temperatures and the vehicle's electrical systems still active, any electrical leakage that produces a spark could lead to an explosion at the gas station. 2. High exhaust pipe temperature: During vehicle operation, the exhaust pipe continues to emit exhaust gases. On one hand, the exhaust pipe remains very hot, and on the other hand, the exhaust gases may carry sparks, creating a safety hazard. Of course, gas stations strictly prohibit staff from pointing the fuel nozzle towards the exhaust pipe.
20
2
Share

What Causes Jerking and Battery Light Flashing When Accelerating?

In manual transmission vehicles, improper coordination between the throttle and clutch, along with high speed and low gear, can cause the engine to rev higher, leading to engine braking and resulting in jerking sensations. Conversely, low speed with high gear can also cause jerking and may even stall the engine. If the engine speed can be maintained around 2,000 RPM while driving, the jerking sensation becomes less noticeable. Other reasons for jerking include: 1. Upshift Jerking: The transmission's response speed is not fast enough, and the upshift speed cannot keep up with the throttle input, causing a jerking sensation during gear shifts. 2. Downshift Jerking: Due to the intervention of the energy recovery system, once the driver releases the throttle pedal or presses the brake pedal, the generator immediately starts working, adding load to the engine. This affects the engine speed, causing it to become out of sync with the clutch plate speed, resulting in a jerking sensation.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.